Honeywell FocusPRO Wi-Fi TH6000 Series User manual

FocusPROTM TH6000 Series
Programmable Thermostat
® U.S. Registered Trademark. Patents pending.
Copyright © 2006 Honeywell International Inc.
All rights reserved.
Installation
Guide
Must be installed by a trained, experienced technician
Read these instructions carefully. Failure to follow these instructions
can damage the product or cause a hazardous condition.
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502
69-1920ES
This manual covers the following models
• TH6110D: For 1 Heat/1 Cool systems
• TH6220D: For up to 2 Heat/2 Cool systems
• TH6320U: For up to 3 Heat/2 Cool systems
(Remove battery holder to find model number)
System Types
• Gas, oil, or electric heat with air
conditioning
• Warm air, hot water, high-
efficiency furnaces, heat pumps,
steam, gravity
• Heat only — two-wire systems,
three-wire zone valves (Series
20), and normally open zone
valves
• Heat only with fan
• Cool only
• 750 mV heating systems

Installation Guide
2
Wallplate installation
1. Separate wallplate from thermostat.
2. Mount wallplate as shown below.
Drill 3/16" holes for drywall. Drill 7/32" holes for plaster.
Wall anchors
Wallplate
Wire hole Mounting screws
CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before
beginning installation.
MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not
place the old control in the trash. Contact your local waste management authority for
instructions regarding recycling and proper disposal.
Pull here to remove wallplate
from new thermostat.
Remove battery holder. Insert reference card after wallplate is
mounted (see instructions, below).
It's easier to grasp the wallplate
and remove it after completely
removing the battery holder.

FocusPROTM TH6110 / TH6220 / TH6320
3
Power options
Keep wires in this
shaded area
Connect Cfor primary AC power
(optional if batteries are installed).
Insert batteries for primary
or backup power.
Remove factory-
installed jumper
only for two-
transformer
systems.
Conventional Terminals:
Rc 24VAC power from cooling
transformer
R 24VAC power from heating
transformer
W Heat relay (stage 1)
W2 Heat relay (stage 2)
Y Compressor contactor (stage 1)
Y2 Compressor contactor (stage 2)
G Fan relay
C 24VAC common. For 2 transformer
systems, use common wire from cooling
transformer.
Heat Pump Terminals:
Rc 24VAC power from cooling
transformer
R 24VAC power from heating
transformer
O/B Changeover valve
Y Compressor contactor (stage 1)
Y2 Compressor contactor (stage 2) -
TH6320U only
G Fan relay
Aux Auxiliary heat relay*
E Emergency heat relay*
L Sends output when set to Em. Heat
C 24VAC common
Wiring
Terminal designations
Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.
TH6110D
RcYWG RC
TH6110D
RcYG RC
TH6220D
Rc
YWGW2Y2 R CRcYGAuxEL RC
TH6220D
TH6320U
Rc
YWGW2Y2 R CRcYGAux
E
Y2L RC
TH6320U
TH6110D
RcYWG RC
TH6110D
RcYG RC
TH6220D
Rc
YWGW2Y2 R CRcYGAuxEL RC
TH6220D
TH6320U
Rc
YWGW2Y2 R CRcYGAux
E
Y2L RC
TH6320U
*Aux and E terminals combined on TH6320U only.

Installation Guide
4
Wiring
Wiring guide — conventional systems
Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.
NOTES
Wire specifications:
Use 18- to 22-gauge thermostat wire.
Shielded cable is not required.
[1] Power supply. Provide disconnect means and
overload protection as required.
[2] Remove jumper for 2-transformer systems.
[3] Optional 24VAC common connection.
[4] Common connection must come from cool-
ing transformer.
[5] In Installer Setup, set system type to Heat Only.
[6] In Installer Setup, set system type to 2Heat/
2Cool Conventional.
[7] In Installer Setup, set changeover valve to O
or B.
[8] In Installer Setup, set system type to 2Heat/
1Cool Heat Pump.
[9] In Installer Setup, set system type to 2Heat/
2Cool Heat Pump.
[10] In Installer Setup, set system type to 3Heat/
2Cool Heat Pump.
[11] L terminal sends a continuous output when
thermostat is set to Em. Heat. Connect to
Honeywell zoning panels to switch the panel
to Emergency Heat.
[12] Install field jumper between Aux and E if
there is no emergency heat relay.
1H/1C System
(1 transformer)
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
W Heat relay
G Fan relay
Heat-only System
Rc Power [1]
R [R+Rc joined by jumper]
C 24VAC common [3]
W Heat relay
Heat-only System
(Series 20) [5]
Rc [R+Rc joined by jumper]
R Series 20 valve terminal “R” [1]
Y Series 20 valve terminal “W”
C 24VAC common [3]
W Series 20 valve terminal “B”
Heat-only System
(normally open zone valve) [5]
Rc [R+Rc joined by jumper]
R Power [1]
Y Normally open zone valve
C 24VAC common [3]
1H/1C System
(2 transformers)
Rc Power (cooling transformer) [1, 2]
R Power (heating transformer) [1, 2]
Y Compressor contactor
C 24VAC common [3, 4]
W Heat relay
G Fan relay
Heat-only System
with Fan
Rc Power [1]
R [R+Rc joined by jumper]
C 24VAC common [3]
W Heat relay
G Fan relay
Cool-only System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
G Fan relay
2H/2C System
(1 transformer) [6]
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor (stage 1)
C 24VAC common [3]
W Heat relay (stage 1)
G Fan relay
W2 Heat relay (stage 2)
Y2 Compressor contactor (stage 2)
2H/2C System
(2 transformers) [6]
Rc Power (cooling transformer) [1, 2]
R Power (heating transformer) [1, 2]
Y Compressor contactor (stage 1)
C 24VAC common [3, 4]
W Heat relay (stage 1)
G Fan relay
W2 Heat relay (stage 2)
Y2 Compressor contactor (stage 2)
See [notes] below
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
Rc
YG R C
RcYWG R CRcWG R
C
RcYWG R C
Rc
YW RC
Rc
Y RC

FocusPROTM TH6110 / TH6220 / TH6320
5
Wiring
Wiring guide — heat pump systems
Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.
Thermostat mounting
Align the 4 tabs on the wallplate with
slots on the back of the thermostat,
then push gently until the thermostat
snaps in place.
Push excess wire back into
the wall opening.
Plug wall opening with
non-flammable insulation.
1H/1C Heat
Pump System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
O/B Changeover valve [7]
G Fan relay
2H/1C Heat
Pump System
(TH6220D only) [8]
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
O/B Changeover valve [7]
G Fan relay
Aux Auxiliary heat relay [12]
E Emergency heat relay [12]
L Sends output when set to Em. Heat [11]
2H/1C Heat
Pump System
(TH6320U only) [8]
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
O/B Changeover valve [7]
G Fan relay
Aux/E Auxiliary/Emergency heat relay
L Sends output when set to Em. Heat [11]
2H/2C Heat
Pump System
(TH6320U only) [9]
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor (stage 1)
C 24 VAC common [3]
O/B Changeover valve [7]
G Fan relay
Y2 Compressor contactor (stage 2)
L Sends output when set to Em. Heat [11]
3H/2C Heat
Pump System
(TH6320U only) [10]
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor (stage 1)
C 24VAC common [3]
O/B Changeover valve [7]
G Fan relay
Aux/E Auxiliary/Emergency heat relay
Y2 Compressor contactor (stage 2)
L Sends output when set to Em. Heat [11]
See [notes] on page 4.
RcYG RC
RcYGAuxEL RC
RcYGAux
E
L RC
RcYGY2
RcYGAux
E
L RC
Y2
L RC
RcYG RC
RcYGAuxEL RC
RcYGAux
E
L RC
RcYGY2
RcYGAux
E
L RC
Y2
L RC
RcYG RC
RcYGAuxEL RC
RcYGAux
E
L RC
RcYGY2
RcYGAux
E
L RC
Y2
L RC
RcYG RC
RcYGAuxEL RC
RcYGAux
E
L RC
RcYGY2
RcYGAux
E
L RC
Y2
L RC
RcYG RC
RcYGAuxEL RC
RcYGAux
E
L RC
RcYGY2
RcYGAux
E
L RC
Y2
L RC

Installation Guide
6
To begin, press and hold the sand FAN
buttons until the display changes.
Function
number Setting
Press s or t to change settings.
Press NEXT to advance to the next function.
Press DONE to exit and save settings.
10
Done Next
Installer setup
Follow the procedure below to configure the thermostat to match the installed
heating/cooling system, and customize feature operation as desired.
Continued on next page
Setup function Settings & options (factory default in bold)
Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.
*[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]
1System type 0 1 heat/1 cool conventional
1 1 heat/1 cool heat pump (no aux. heat)
2 Heat only — 2-wire systems, 3-wire zone valves (Series 20), and
normally open zone valves
3 Heat only with fan
4 Cool only
5 2 heat/1 cool heat pump (with aux. heat)
6 2 heat/2 cool conventional
7 2 heat/1 cool conventional
8 1 heat/2 cool conventional
9 2 heat/2 cool heat pump (no aux. heat) - TH6320U only
10 3 heat/2 cool heat pump (with aux. heat) - TH6320U only
2Changeover valve
(O/B terminal)
0 Changeover valve (O/B terminal energized in cooling)
1 Changeover valve (O/B terminal energized in heating)
3Fan control
(heating)
0 Gas or oil furnace — equipment controls fan in heating
1 Electric furnace — thermostat controls fan in heating
5Stage 1 heat cycle
rate (CPH: cycles/hour)*
5 For gas or oil furnaces of less than 90% efficiency
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
9 For electric furnaces
6Stage 2 heat cycle
rate/Auxiliary heat
cycle rate (CPH)*
5 For gas or oil furnaces of less than 90% efficiency
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
9 For electric furnaces
7Auxiliary heat cycle
rate (CPH)*
Only TH6320U
for 3H/2C Heat Pumps
5 For gas or oil furnaces of less than 90% efficiency
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
9 For electric furnaces
8Emergency heat cycle
rate (CPH)*
9 For electric emergency heat
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
5 For gas or oil furnaces of less than 90% efficiency

FocusPROTM TH6110 / TH6220 / TH6320
7
System test System status
Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.
Press s / t to turn system on/off.
Press NEXT to advance to next test.
Press DONE to terminate system test.
Test number System status
10 0
To begin, press and hold the s and t
buttons until the display changes.
Installer setup
Setup function Settings & options (factory default in bold)
Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.
9Stage 1 compressor
cycle rate (CPH)
3 Recommended for most compressors
[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]
10 Stage 2 compressor
cycle rate (CPH)
3 Recommended for most compressors
[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]
12 Manual/Auto
changeover
0 Manual changeover (Heat/Cool/Off)
1 Auto changeover (Heat/Cool/Auto/Off) **See page 8
2 Auto changeover only (Auto) **See page 8
13 Adaptive Intelligent
Recovery™
1 On**See page 8
0 Off
14 Temperature
display
0 Fahrenheit
1 Celsius
15 Compressor
protection
5 Five-minute compressor off time **See page 8
[Other options: 0, 1, 2, 3 or 4-minute off time]
16 Schedule format 0 5/2 (programmable weekdays and weekends)
1 5/1/1 (weekdays, Saturday & Sunday programmable)
27 Heat temperature
range stops
90 Max. heat temperature setting is 90° F (32° C)
[Other options: 40 �F to 89 �F (4.5 �C to 31.5 �C)]�F to 89 �F (4.5 �C to 31.5 �C)]F to 89 �F (4.5 �C to 31.5 �C)]�F (4.5 �C to 31.5 �C)]F (4.5 �C to 31.5 �C)]�C to 31.5 �C)]C to 31.5 �C)]�C)]C)]
28 Cool temperature
range stops
50 Min. cool temperature setting is 50° F (10° C)
[Other options: 51 �F to 99 �F (10.5 �C to 37 �C)]�F to 99 �F (10.5 �C to 37 �C)]F to 99 �F (10.5 �C to 37 �C)]�F (10.5 �C to 37 �C)]F (10.5 �C to 37 �C)]�C to 37 �C)]C to 37 �C)]
Installer system test
10 Heating system 0 Heat and fan turn off.
1 Stage 1 heat turns on. Fan turns on if Setup Function 1 is set to 1,
5, 9 or 10 OR Setup Function 3 is set to 1 **See page 6
2 Stage 2 heat turns on
3 Stage 3 heat turns on - TH6320U only
20 Emergency heating
system
0 Heat and fan turn off
1 Heat and fan turn on
2 Stage 2 heat turns on (auxiliary heat) - TH6220D only
30 Cooling system 0 Compressor and fan turn off
1 Compressor and fan turn on
2 Stage 2 compressor turns on
40 Fan system 0 Fan turns off
1 Fan turns on
CAUTION: Compressor protection is bypassed during testing. To prevent equipment
damage, avoid cycling the compressor quickly.

Installation Guide
® U.S. Registered Trademark.
© 2006 Honeywell International Inc.
69-1920ES M.S. 03-06
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
http://yourhome.honeywell.com
Automation and Control Solutions
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Scarborough, Ontario M1V4Z9
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
Special functions
Auto Changeover (Setup Function 12): When set to Auto, the thermostat automatically selects
heating or cooling depending on the indoor temperature. The thermostat will automatically
adjust heat and cool settings to maintain a 3-degree separation (fixed). Note: If you select Auto
Changeover Only, the System Setting on the thermostat will stay locked in the Auto position,
preventing the user from changing it to Em Heat, Heat, Cool or Off.
Adaptive Intelligent Recovery™(Setup Function 13): Allows the thermostat to “learn” how
long the furnace and air conditioner take to reach programmed temperature settings, so the
temperature is reached at the scheduled time.
Compressor Protection (Setup Function 15): Forces the compressor to wait a few minutes
before restarting, to prevent damage. During the wait time, the message Cool On or Heat On
(heat pumps only) will flash on the display.
Accessories & replacement parts
Please contact your distributor to order replacement parts.
Battery holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . Part Number 50007072-001
Cover plate assembly*. . . . . . . . . . . . . . . . . . . . . Part Number 50002883-001
12 pack of medium cover plates*. . . . . . . . . . . . Part Number 50007298-001
*Use to cover marks left by old thermostats.
Specifications
Temperature Ranges
• Heat: 40� to 90�F (4.5� to 32�C)
• Cool: 50� to 99�F (10� to 37�C)
Operating Ambient Temperature
• 32� to 120�F (0� to 48.9�C)
Shipping Temperature
• -20� to 120�F (-28.9� to 48.9�C)
Operating Relative Humidity
• 5% to 90% (non-condensing)
Physical Dimensions
• 3-9/16" H x 5-13/16" W x 1-1/2" D
91 mm H x 147 mm W x 38 mm D
Electrical Ratings
Terminal Voltage (50/60Hz) Running Current
WHeating 20-30 Vac 0.02-1.0 A
(Powerpile) 750 mV DC 100 mA DC
W2 (Aux) Heating 20-30 Vac 0.02-0.5 A
YCooling 20-30 Vac 0.02-1.0 A
Y2 Cooling 20-30 Vac 0.02-1.0 A
GFan 20-30 Vac 0.02-0.5 A
O/B Changeover 20-30 Vac 0.02-0.5 A
EEmergency heat 20-30 Vac 0.02-1.0 A
LOutput 20-30 Vac 0.02-0.5 A

Serie FocusPROTM TH6000
Termostato programable
® Marca registrada de los EE. UU. Patentes en trámite.
© 2006, Honeywell International Inc.
Todos los derechos reservados.
Guía de
instalación
Debe ser instalado por un técnico capacitado y experimentado
Lea estas instrucciones atentamente. Si no sigue estas instrucciones,
puede dañar el producto u ocasionar un riesgo.
¿Necesita asistencia?
Para obtener asistencia relacionada con este producto,
visite http://yourhome.honeywell.com o comuníquese con el número gratuito
del servicio de atención al cliente de Honeywell, llamando al 1-800-468-1502
69-1920ES
Este manual incluye los siguientes modelos:
• TH6110D: para sistemas de 1 calentador y 1 refrigerador
• TH6220D: para sistemas de 2 calentadores y 2 refrigeradores
• TH6320U: para sistemas de 3 calentadores y 2 refrigeradores
(Quite el soporte de la batería para ver el número de modelo)
Tipos de sistemas
• Sistema de calefacción de gas,
de aceite o eléctrico con aire
acondicionado
• Calefacción de aire, agua
caliente, sistemas de calefacción
de alta efectividad, bombas de
calor, vapor, gravedad
• Sólo calor: sistemas de 2 cables,
válvulas de separación de tres
cables (serie 20) y válvulas de
separación normalmente abiertas
• Sólo calor con ventilador
• Sólo frío
• Sistemas de calefacción de 750 mV

Guía de instalación
2
Instalación de la placa para pared
En tablarroca, realice agujeros de 3/16". En yeso, realice agujeros de 7/32".
Anclas de expansión
Placa para pared
Agujero para
el cable Tornillos de montaje
PRECAUCIÓN: RIESGO ELÉCTRICO
Puede ocasionar descargas eléctricas o dañar el equipo. Desconecte la energía
eléctrica antes de comenzar la instalación.
AVISO SOBRE EL MERCURIO
En caso de que este producto reemplace a un control que contenga mercurio
en tubo sellado, evite arrojar el viejo control a la basura. Póngase en contacto con
la autoridad local para el manejo de desechos a fin de obtener instrucciones sobre
el reciclado y la correcta eliminación de este tipo de desechos.
Hale de aquí para quitar
la placa para pared del
nuevo termostato.
Extraiga el soporte de la batería. Introduzca la tarjeta de referencia
luego de montar la placa para
pared (lea las instrucciones
que aparecen abajo).
Es más fácil quitar la placa para
pared una vez que se extrae
completamente el soporte
de la batería.
1. Quite la placa para pared del termostato.
2. Monte la placa para pared como muestra
la ilustración de abajo.