Honeywell T6R-HW User manual

Complete
installation
5
Prepare Receiver Box
for installation
2Install the
Receiver Box
3
B) Surface wiring
C) Replace the cover
min 0.25mm2
max 1.5mm2
Needed during installation:
Cable with 2 wires from the boiler to Receiver Box.
The Receiver Box requires 230V power
Before installation of the
Receiver Box
Find a suitable location near
to the boiler. Leave at least
30cm distance from any
metal objects including
wallboxes and boiler
housing.
Loosen the front
screw to remove
cover or tighten it
when the cover is
back in place.
Max 6 mm
Please refer to the wiring
diagrams over the page
32308181-020 A
After
powering up both
devices the green
LED is on.
Turn ON mains power to the Heating Appliance and Receiver Box.
Push the buttons to
check if the boiler
switches on.
Buttons light green.
After power up,
SETUP is displayed on
the thermostat screen.
To rebind the units, reset the Receiver box, then press the button for 3 seconds.
The LED on the receiver box will blink yellow to indicate the box is in binding
mode. On the thermostat press for 5 seconds to enter the advanced menu.
Navigate to Binding, clear the current binding then bind the device again.
Reset
A) Wall box or Rear Wiring
Hinge open the terminal block flap
to access the cables and wall box
screw holes.
Use the cable clamps to secure the
surface wiring.
Locate the
hinges at the top
of the cover and
wall plate, close
the cover and
secure with the
screw.
Turn OFF the power
and remove the old thermostat
1
To ensure your safety, always make sure mains power is switched OFF before
accessing wiring.
In case of removing the old thermostat be aware that the existing wiring will
no longer be used.
The T6R-HW thermostat should not be placed near draughts, in direct
sunlight or near heat sources.
WEEE Directive 2012/19/EC
Waste Electrical and Electronic Equipment directive
At the end of the product life dispose of the packaging and product in a
corresponding recycling centre. Do not dispose of the unit with the usual
domestic refuse. Do not burn the product.
Must be installed by a competent person!
Read these instructions carefully. Failure to follow these instructions
can damage the product or cause a hazardous condition.
Need help? For assistance please visit: getconnected.honeywell.com
Honeywell Control Systems Ltd., Skimped Hill Lane,
Bracknell, Berkshire, RG12 1EB
Compatible with Sundial Y- and S-plan stored hot water
systems with zone valves. Also compatible with 24-230V
on/off appliances such as gas boilers, combi-boilers and
heat pump.
Approvals
Conforms to protection requirements of the following directives: EMC: 2014/30/EU,
LVD: 2014/35/EU and RED: 2014/53/EU. Hereby, Honeywell, declares that this
thermostat is in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU. The full text of the EU Declaration of Conformity
is available at the following Internet address: http://hwll.co/DoC
RF (868MHz): Receiver Category 2, Max RF Power 25mW, 868–868.6MHz (868.3MHz)
Wi-Fi (2.4GHz): Max Power 100mW, 2.4–2.458GHz
ErP: Class V (+3%), (EU) 811/2013
Install the
T6RHW thermostat
4
Choose the appropriate plug.
Place the thermostat on an even, horizontal surface and plug it in.
1.70 m
T6R-HW
SMART THERMOSTAT
All manuals and user guides at all-guides.com
all-guides.com

4) Touch to finalise setup.
( to setup using the App is
currently unsupported)
www.honeywelluk.com/
professional-zone/resource-centre/
WiringDiagrams/
For other wiring
diagrams visit:
Set Up and
configuration
6
Wiring Diagrams
Once setup is completed, if you need to
change more settings go to the advanced
menu. To access the advanced menu
press for 5 seconds.
In the advanced menu the following
settings can be adjusted:
AM
PM
AM
PM
AM
PM
*1234
1 2 3 4 5 6
*****230****
5 sec
Menu Item Default Options
***SETUP****
SETUP
**LANGUAGE**
*CLOCK
SETUP
1) Touch to begin
setting up the thermostat.
2) Select your language.
3) Set the clock format,
time and date.
SETUP
A) Sundial S-plan B) Sundial Y-plan
* See boiler specifications for correct terminals
CONFIGURE W
C) Combi boiler
Receiver Box
T1 T2
Boiler*
D) OpenTherm boiler
Receiver Box
Boiler*
T1 T2
Boiler
Receiver Box
V4043 V4043
Cylinder thermostat
1
2
MidPosition
zone valve
Boiler
Receiver Box
V4073A
Cylinder thermostat
1
2
LANGUAGE
OPENTHERM
SYSTEM TYPE
CYCLE RATE
MINIMUM ON TIME
HEAT RANGE
SCHEDULE OPTIONS
OPTIMISE
CLOCK
LOW LOAD CONTROL
TEMPERATURE OFFSET
BINDING
RESET
FAILSAFE
English
Heat+HW
6
ON 0 = off, 1 = on
OFF
-
-
-
0 = off, 1 = on
0.0ºC 1.5 ºC to 1.5ºC
Bind , check RF and clear bind.
Factory, schedule, WiFi and HomeKit reset
Clock format: 1 = 12h, 2 = 24h
Setup time and date
1 minute
3, 6, 9 or 12
Daily
Opt. start OFF
Opt. stop OFF
Opt. start: 0 = off, 1 = on, 2 = Delayed start
Opt. stop: 0 = off, 1 = on
Format: 24h
Time: --:--
Date: 01/09/16
1, 2, 3, 4 or 5 minutes
Min = 5.0ºC
Max = 35.0ºC
1 = Daily schedule, 2 = 5+2 days schedule
Min: 5ºC to 21ºC, Max: 21ºC to 35ºC
0 = English, 1 = Français, 2 = Español
3 = Deutsch, 4 = Nederlands, 5 = Italiano
Heating only, Heating + Hot Water, Heating
+ Cooling
OpenTherm boiler data when available
Manufactured for and on behalf of the Environmental and Energy Solutions Division of Honeywell
Technologies Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle, Switzerland by its Authorised
Representative Honeywell Inc.
For security
reasons: Route
this wiring
through conduit
or in the wall so it
is not accessible.
All manuals and user guides at all-guides.com