Honeywell FocusPRO TH5000 Series User manual

FocusPRO® TH5000 Series
Non-Programmable Digital Thermostat
69-1923EFS-01
Operating
Manual

ENGLISH
Read and save these instructions.
® U.S. Registered Trademark. Patents pending.
Copyright © 2009 Honeywell International Inc. All rights reserved.
Battery Holder
Press down and pull to remove
batteries. Batteries should be
replaced once a year (see page 10).
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502
This manual covers the following models:
TH5110D: For 1 Heat/1 Cool systems
TH5220D: For up to 2 Heat/2 Cool systems
TH5320U: For up to 3 Heat/2 Cool systems
(Remove battery holder to find model number)
MCR29404

FocusPRO®TH5000 Series
1 69-1923EFS—01
ENGLISH
About your new thermostat
Thermostat features...................................2
Setup at a glance.......................................3
Quick reference to controls.......................4
Quick reference to display ........................5
Programming & Operation
Fan setting (auto/on)..................................6
System setting (heat/cool/auto)................7
Auto-changeover (heat/cool).....................8
Compressor protection..............................9
Appendices
Battery replacement ................................10
In case of difficulty...................................11
Customer assistance ............................... 13
Accessories/replacement parts ............. .13
5-year limited warranty............................14
Table of contents
CAUTION: EQUIPMENT DAMAGE
HAZARD. To prevent possible
compressor damage, do not operate
cooling system when outdoor
temperature is below 50°F (10°C).

ENGLISH
About your new thermostat
Congratulations on the purchase of your new Honeywell thermostat. It has been
designed to give you many years of reliable service and easy-to-use, push-button
climate control.
Features
• One-touchtemperaturecontrol.
• Large,clear,backlitdisplayiseasytoread—eveninthedark.
• Displaysbothroomtemperatureandtemperaturesetting.
• Removablebatteryholderforfast,easyreplacement.
• Built-incompressorprotection.
Operating Manual
2

FocusPRO®TH5000 Series
3 69-1923EFS—01
ENGLISH
This thermostat is ready to go!
Your new thermostat is pre-programmed by the installer and ready to use. Just check
the settings below and change if needed:
1. Fan (Auto/On): Preset to Auto.........................................To change, see page 6.
Auto is the most commonly used setting, but you may
prefer On for improved air circulation.
2. System (Heat/Cool/Auto/Em. Heat): Preset to Heat ...To change, see page 7.
You can select heating or cooling, or set the system
to control both systems automatically, if needed.

Operating Manual
69-1923EFS—01 4
ENGLISH
M29405
Digital display (see page 5) Battery holder (see page 10)
Temperature Buttons
Press to set preferred
temperature.
Function Buttons
Press to select the function displayed just above each
button. (Functions change depending on the task.)
Quick reference to controls

FocusPRO®TH5000 Series
5 69-1923EFS—01
ENGLISH
Auxiliary
Heat On
Heat
Setting
Inside
72
72
Replace
Battery
Auto
Fan
Heat
System
MCR29406
Current inside
temperature
Function buttons
Press the button beneath each function to view or change
settings (functions change depending on the task)
Low battery warning (see page 10)
Temperature
setting
System status
HeatOn/CoolOn
(If flashing, see page 9)
System setting
Heat/Cool/Auto/Off/
Em Heat (see page 7)
Fan setting
Auto/On(seepage6)
Quick reference to display screen
Auxiliary heat(Onlyforheat
pumps with auxiliary heat)

Operating Manual
69-1923EFS—01 6
ENGLISH
Press the FAN button to select Auto or On.
In “Auto” mode (the most commonly used
setting), the fan runs only when the heating
orcoolingsystemison.Ifsetto“On,”thefan
runs continuously.
Select the fan setting
Heat
System
Auto
Fan
Heat
System
On
Fan
MCR29407

FocusPRO®TH5000 Series
7 69-1923EFS—01
ENGLISH
Press the SYSTEM button to select:
• Heat: Thermostat controls only the
heating system.
• Cool: Thermostat controls only the
cooling system.
• Off: Heating and cooling systems are off.
• Auto: Thermostat automatically selects
heating or cooling depending on the
indoor temperature.
• Em Heat (only for heat pumps with
auxiliary heat): Thermostat controls
Emergency and Auxiliary Heat.
Compressor is locked out.
Select the system setting
Note: The Auto and Em Heat
system settings may not
appear, depending on how
your thermostat was installed.
Heat
System
Auto
Fan
Cool
System
Auto
Fan
MCR29408

Operating Manual
69-1923EFS—01 8
ENGLISH
Auto Changeover is a feature used in climates
where both air conditioning and heating are
used on the same day. When the system is set
to Auto, the thermostat automatically selects
heating or cooling depending on the indoor
temperature.
Heat and cool settings must be at least 3
degrees apart. The thermostat will automati-
cally adjust settings to maintain this 3-degree
separation (called “deadband”).
The 3-degree separation between heating and
cooling set temperatures is fixed, and cannot
be changed.
Auto changeover (heat/cool)
Press until screen
displays “Auto”
Note: The Auto system setting may
not appear, depending on how your
thermostat was installed.
Auto
System
Auto
Fan
MCR29409