Honeywell T8700B Operation manual

PRODUCT DATA
® U.S. Registered Trademark
Copyright © 1998 Honeywell Inc. • • All Rights Reserved
T8700B,C
An Electronic Round™
Programmable Thermostat
APPLICATION
The T8700 Electronic Round™ Programmable Thermostats
provide single-stage, programmable temperature control for
24V heating and/or cooling systems. See Table 1 for model
descriptions.
Table 1.T8700 Thermostat Description.
FEATURES
•Attractive neutral styling complements any decor.
•Easy-to-use means fewer homeowner questions and
increased homeowner satisfaction.
•Large easy-to-read display.
•Keys located near the display for easy access.
•Fan and System switches are located on the top of the
wallplate to eliminate accidental setting changes.
•Quick and easy installation.
Two-period programming for added energy savings.
• Manual changeover from heat to cool eliminates
unexpected system operation (T8700C).
•°F or °C temperature display for added model
flexibility.
•Selectable heating cycle rate (1, 3, 6 or 9 cph) allows a
variety of applications and reduced inventory.
•Cooling (T8700C) cycle rate fixed at 3 cph (the standard
setting for compressors) allows a speedy installation.
•Programming permanently held in memory (no
batteries needed) and retained during power outages
for increased installer and homeowner convenience.
•Compatible with most equipment and application
needs including gas, oil and electric forced air;
condensing gas furnaces; hydronic heat; and gravity
and radiant heat systems.
•Powerstealing eliminates need to run additional wires.
Contents
Application........................................................................... 1
Features .............................................................................. 1
Specifications ...................................................................... 2
Ordering Information ........................................................... 2
Installation ........................................................................... 3
Settings and Adjustments ................................................... 6
Setting the Clock ................................................................. 7
Programming....................................................................... 7
Operation ............................................................................ 8
Checkout ............................................................................. 10
Troubleshooting ................................................................... 11
68-0197-1
T8700C
Model System Selection Fan Selection
Wiring
Terminals
Used
T8700B1007 HEAT-OFF NONE R,W
T8700B1015 HEAT-OFF ON-AUTO R,G,W
T8700C1005 HEAT-OFF-
COOL ON-AUTO R,G,W,Y

T8700B,C AN ELECTRONIC ROUND™ PROGRAMMABLE THERMOSTAT
68-0197—1 2
ORDERING INFORMATION
When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the
TRADELINE® Catalog or price sheets for the complete ordering number.
1. Order number.
2. Accessory, if desired.
If you have additional questions, need further information, or would like to comment on our products or services, please write or
phone:
1. Your local Home and Building Control Sales Office (check white pages of your phone directory).
2. Home and Building Control Customer Logistics
Honeywell Inc., 1985 Douglas Drive North
Minneapolis, Minnesota 55422-4386
In Canada—Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.
International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,
Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.
SPECIFICATIONS
IMPORTANT
The specifications given in this publication do not
include normal manufacturing tolerances; therefore,
an individual unit might not exactly match the listed
specifications. Also, this product is tested and
calibrated under closely controlled conditions and
some minor differences in performance can be
expected if those conditions are changed.
T8700 TRADELINE® models include a thermostat, wallplate,
decorator cover plate and owner’s guide. The package also
includes a resistor for use with Taco zone valves. See Fig. 11.
Power:
T8700: 24 Vac nominal, 18 to 30 Vac, 60 Hz.
Electrical Ratings:
Heating: .02 to 1.2A run; 3.5A inrush.
Cooling: .02 to 1.2A run; 6.0A inrush.
Fan: .02 to 0.5A run; 2.5A inrush.
Current Draw:
T8700 Power Stealing Thermostat requires only 2.5 mA
current draw when the thermostat calls for heat or cool and is
compatible with most 24V systems. It can be used in most
non-millivolt applications. See Power Stealing in the Operation
section.
Temperature Adjustment:
Setpoint temperature is adjusted by using the or keys.
One press changes the setpoint one degree; pressing and
holding changes the setpoint several degrees.
Temperature Setting Range:
40°F (4°C) to 99°F (37°C).
Operational Ambient Temperature Range:
30°F (4°C) to 110°F (43°C).
Shipping Temperature Range:
-20°F (29°C) to 120°F (49°C).
Operating Relative Humidity:
5% to 90% RH, noncondensing.
Cycle Rates (at 50 Percent Load):
Heating: Selectable at 1, 3, 6 or 9 cph. See Table 2 for
heating cycle rates and corresponding system equipment.
Cooling (T8700C): Fixed at 3 cph.
Table 2. Heating Cycle Rates.
Finish:
T8700: Premier White® color.
Dimensions:
See Fig. 1.
Fig. 1. T8700 Thermostat dimensions (T8700C shown).
System Cycles per Hour (cph)
Steam, Gravity 1
Hydronic Heat, Condensing Gas Furnaces 3
Gas or Oil Forced Air 6
Electric Furnace 9
Set
M12579
C
O
O
L
O
F
F
H
E
A
T
F
A
N
O
N
A
U
T
O
4-1/4
5-1/2
1-1/2
3-1/2
PM
T8700
THERMOSTAT
DECORATOR
COVER PLATE

T8700B,C AN ELECTRONIC ROUND PROGRAMMABLE THERMOSTAT
68-0197—1
3
INSTALLATION
When Installing this Product…
1. Read these instructions carefully. Failure to follow them
could damage the product or cause a hazardous
condition.
2. Check the ratings given in the instructions and on the
product to make sure the product is suitable for your
application.
3. Installer must be a trained, experienced service
technician.
4. After installation is complete, check out product
operation as provided in these instructions.
CAUTION
Damage To Heating/Cooling System Possible.
Be careful when handling wires during installation.
Disconnect power at furnace or at main breaker/fuse
box before starting installation.
RECYCLING NOTICE
If this control is replacing a control that contains
mercury in a sealed tube, do
not place your old
control in the trash.
Contact your local waste management authority for
instructions regarding recycling and the proper
disposal of an old control containing mercury in a
sealed tube.
Fig. 2. Typical thermostat location.
Location
Install the thermostat about 5 ft (1.5m) above the floor in an
area with good air circulation at average temperature. See
Fig. 2. Do not install the thermostat where it can be affected by:
—Drafts or dead spots behind doors and in corners.
—Hot or cold air from ducts.
—Radiant heat from the sun or appliances.
—Concealed pipes and chimneys.
—Unheated (uncooled) areas such as an outside wall
behind the thermostat.
Mounting Decorator Cover
Plate and Wallplate to Wall
IMPORTANT
Position and level the wallplate for appearance only.
The thermostat functions properly even when not
level.
Mount decorator cover plate (if desired), wallplate, T8700 and
the screws as follows; see Fig. 3:
1. Place the decorator cover plate and the wallplate on the
desired wall location.
2. Pull the thermostat wire through the entrance hole on
the decorator cover plate, then through the wallplate
entrance hole.
3. Plug the wiring hole behind the thermostat to prevent
drafts from affecting the thermostat.
4. Select the two mounting holes that best fit the
application.
5. Fasten the decorator cover plate and the wallplate to
the wall using the provided anchors (if necessary) and
screws.
5 FEET
[1.5 METERS]
YES
NO
NO
NO
M12524

T8700B,C AN ELECTRONIC ROUND™ PROGRAMMABLE THERMOSTAT
68-0197—1 4
Fig. 3. Mounting decorator cover plate
and wallplate on wall (T8700C shown).
Wiring
CAUTION
Damage To Heating/Cooling System Possible.
Be careful when handling wires
during installation.
Disconnect power at furnace or at main breaker/fuse
box.
IMPORTANT
Use an 18-gauge maximum wire for wiring the
T8700 Thermostat.
All wiring must comply with local electrical codes and
ordinances. A letter is located near each terminal for
identification.
NOTE: To ensure proper mounting of thermostat, restrict all
wiring to the left side of the terminals. See Fig. 4.
Fig. 4.T8700C wallplate wiring connections.
(Refer to Table 1 for T8700B wiring connections.)
The shape of the terminals permits insertion of straight or
wraparound wiring connections; either method is acceptable.
See Fig. 5.
Fig. 5. Wiring connections.
The T8700 Thermostat steals power through the heating and/or
cooling system controls and is adaptable to most, 24 Vac
systems. Refer to Fig. 6 through 11 for typical wiring hookups.
M12529
ALTERNATE
MOUNTING
SCREW HOLE
MOUNTING
SCREW
HOLE
MOUNTING
SCREW HOLE
ROUTE WIRING AS
SHOWN THROUGH
ENTRANCE
HOLE
WIRING ENTRANCE HOLE
ALTERNATE MOUNTING
SCREW HOLE
W
Y
G
R
C
O
O
L
O
F
F
H
E
A
T
F
A
N
O
N
A
U
T
O
M12537
FOR WRAPAROUND, STRIP
7/16 IN. (11 mm)
FOR STRAIGHT INSERTION,
STRIP 5/16 IN. (8 mm)
Fig. 6. T8700B1007 Heat Only wiring diagram
T8700B1015 Heat Only with Fan includes dotted line.
M12532A
DECORATOR
COVER PLATE
WALL
WALLPLATE
PLASTIC SCREW
ANCHOR (2)
C
O
O
L
O
F
F
H
E
A
T
F
A
N
O
N
A
U
T
O
1
1WHEN USING WALL ANCHORS, DRILL 3/16 INCH HOLES FOR
DRYWALL, 7/32 INCH HOLES FOR PLASTER OR WOOD.
L1
(HOT)
L2
1
1
W
R
HEATING
PRIMARY
CONTROL
24V
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
M16005B
T8700B
FAN
RELAY
G

T8700B,C AN ELECTRONIC ROUND PROGRAMMABLE THERMOSTAT
68-0197—1
5
Fig. 7.T8700C heat-cool wiring diagram in single trans-
former system with gas or electric heat/electric cooling.
Fig. 9. T8700B1007 Heat Only wiring diagram in
electric baseboard or ceiling cable system.
Fig. 8. T8700C heat-cool wiring diagram
in oil heating/electric cooling system.
(Oil primary has its own transformer.)
Fig. 10. T8700B1007 Heat Only wiring diagram
for controlling 2-wire hot water zone valves.
Fig. 11. T8700B1007 Heat Only diagram used with TACO
zone valves.The 7870 OHM resistor is included.
L1
(HOT)
L1
(HOT)
L2
L2
1
1
1
W
Y
G
R
COOLING
CONTACTOR
FAN
RELAY
OIL PRIMARY
CONTROL
TT
24V
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED. M12526
T8700
M12623
L1
(HOT)
L2
1
1
2
2
3
2 2
3 3 3
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
CONNECT V8043E YELLOW LEADWIRE TO THERMOSTAT.
CONNECT V8043E RED LEADWIRES TO AQUASTAT®.
T8700T8700T8700
V8043E
CIRCULATOR
T
RWRWRW
T
1
2C1
TO
BURNER
CONTROL
CIRCUIT
B1
B2
C2
V8043EV8043E
1
2
3
RESISTOR
L1
(HOT)
L2
1
1
THERMOSTAT T8700B
RW
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
CONNECT 7870 OHM RESISTOR TO THE TACO ZONE
VALVE TERMINALS 1 AND 2. (TO ORDER, USE PART
NO. 4074EYC.)
TAC O ZONE VALVE
M13178
2
2
L1
(HOT)
L2
1
1
W
Y
G
R
COOLING
CONTACTOR
FAN
RELAY
HEATING
PRIMARY
CONTROL
24V
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED. M13207
T8700
L1
(HOT)
L2
1
W
R
1POWER SUPPLY. PROVIDE DISCONNECT MEANS
AND OVERLOAD PROTECTION AS REQUIRED. M12527B
RESISTANCE
HEATER
SWITCH
HEATER
BLACK
BLUE
RED
RED
WHITE
R841C
BIMETAL
SWITCH
T8700

T8700B,C AN ELECTRONIC ROUND™ PROGRAMMABLE THERMOSTAT
68-0197—1 6
Adjust Fan Operation Switch
The thermostat fan operation switch, labeled Fuel switch, is set
at the factory in the F position. See Fig. 12. This is the correct
setting for most systems. If this system is an electric heat
system, set the switch to the E position.The E setting allows the
fan to turn on immediately with the heating or cooling
equipment in a system where the G terminal is connected.
Fig. 12. Fuel switch, rear view of thermostat.
Mounting Thermostat to Wallplate
1. Align and attach bottom center notch on the thermostat
with bottom center tab on wallplate.
2. Next align tabs and connector at top of thermostat to
the pins on the wallplate. Press firmly to attach.
Fig. 13. Mounting thermostat to wallplate.
NOTE: To remove the thermostat from the wallplate, grasp
the thermostat on both sides and pull the thermostat
straight out.
Fig. 14. T8700 time/temperature display
and System/Fan switches (T8700C shown).
Fan Switch
The Fan switch settings for the T8700B1015 with Fan and
T8700C are:
ON: The fan runs continuously. Use to improve air circulation.
AUTO: Normal setting for most homes. In cooling, the fan
starts and stops with the cooling equipment. In heating,
the heating system directly controls the fan equipment.
The fan may start a few minutes after the heating
equipment turns on (for most systems). When the
thermostat Fuel switch is set to the E position for electric
heat, the fan starts and stops with heating equipment.
Slide the Fan switch on the thermostat to the desired fan
setting.
System Switch
The T8700B System switch controls the thermostat as follows:
HEAT: The thermostat controls the heating system.
OFF: Heating is off.
The T8700C System switch controls the thermostat as
follows:
COOL: The thermostat controls the cooling system.
OFF: Both heating and cooling are off.
HEAT: The thermostat controls the heating system.
Slide the System switch on the thermostat to the desired
system setting.
Set
M12546A
TIME/TEMPERATURE
DISPLAY
INCREASE
SETTING
DECREASE
SETTING
FAN SWITCH
(SOME MODELS)
SYSTEM SWITCH
C
O
O
L
O
F
F
H
E
A
T
F
A
N
O
N
A
U
T
O
PM
SETTINGS AND ADJUSTMENTS
Setting Fan and System Switches
Fan and system settings are controlled manually using the
switches located at the top of the thermostat wallplate. See
Fig. 14 for switch locations.
M12531A
FUEL SWITCH
FE
1
1T8700C AND T8700B WITH FAN ONLY.
CONNECTOR
M13208
ALIGN AND ATTACH BOTTOM CENTER NOTCHS ON
THERMOSTAT/WALLPLATE.
ALIGN PINS ON WALLPLATE WITH CONNECTOR ON
THERMOSTAT. PRESS FIRMLY TO ATTACH.
AA
C
O
O
L
O
F
F
H
E
A
T
F
A
N
O
N
A
U
T
O
BOTTOM CENTER
NOTCH
PINS
B
Set

T8700B,C AN ELECTRONIC ROUND PROGRAMMABLE THERMOSTAT
68-0197—1
7
2. Set your WAKE time.
a. Press the key
once.You will see a
flashing WAKE time.
b. Use the or keys to set your desired WAKE
time. The WAKE time is now set.
3. Set your WAKE
temperature.
a. Press the key
once.You will see a
flashing WAKE
temperature.
b. Use the or keys to set your desired WAKE
temperature.The WAKE temperature is now set.
4. Set your SLEEP time.
a. Press the key
once.You will see a
flashing SLEEP time.
b. Use the or keys to set your desired SLEEP
time. The SLEEP time is now set.
5. Set your SLEEP
temperature.
a. Press the key
once.You will see a
flashing SLEEP
temperature.
b. Use the or keys to set your desired SLEEP
temperature.The SLEEP temperature is now set.
6. Run program.
a. Press the key
once.You have
completed your
program changes.
End is displayed for
five seconds indica-
ting the end of
programming. The
thermostat then
displays the current
time and room temperature.
NOTE: To exit the programming mode at any time, press the
key until End is displayed.
SETTING THE CLOCK
1. To set the current time:
a. Press the key
once.You will see a
flashing clock.
b. Use the or keys to set the current time.
c. Press the key until End is displayed.
PROGRAMMING
The thermostat is preprogrammed for your convenience with
the following time and temperature settings, see Table 3.
Table 3. Preprogrammed Time/Temperature Settings.
PM
M12506
AM
M12507
AM
M12508
SET
PM
M12509
PM
M12506
PM
M12510
SET
M12511
PM
M12542
Period Start Time Heating Setpoint Cooling Setpointa
WAKE 6:00 AM 70°F (21°C) 78°F (25.5°C)
SLEEP 10:00 PM 62°F (16.5°C) 82°F (28°C)
aT8700C only.
WAKE is the time period when you want the house at a
comfortable temperature during the day.
SLEEP is the time period you can set for an energy-saving
temperature while you sleep.
NOTE: The heating and cooling program times are the
same. Changing your cooling WAKE time also
changes your heating WAKE time.
The following is a heating program example. The System
switch is in the HEAT position. To change to the cooling
program (T8700C), move the System switch to the COOL
position and enter the cooling temperature settings.
IMPORTANT
When programming the T8700B, first move the
System switch to the heat position.
To program your own Time and Temperature settings
follow steps 1 through 6.
1. Set the current time.
a. Press the key
once.You will see a
flashing clock.
b. Use the or keys to set the current time. The
clock is now set.
Preprogrammed Time and Temperature settings.
After the clock is set, you can use the preprogrammed
Time and Temperature settings, (see table 3) press the
key until End is displayed.
The preprogrammed Temperature settings can now be
used.

T8700B,C AN ELECTRONIC ROUND™ PROGRAMMABLE THERMOSTAT
68-0197—1 8
3. Select Fahrenheit - CelsiusTemperature.
a. Press to
display the current
°F or °C setting.
b. Use or to
choose between °C
and °F.
4. Clock Format.
a. Press to
display the current
12- or 24-hour clock
setting.
b. Use or to
choose either a 12- or 24-hour clock format.
Press once to exit
Installer Setup. Upon
exiting, the temperature
setting will be at 52°F
(or 11°C). Press six
times to return the
thermostat to the normal operating mode with End
appearing on the display.
Operating the Thermostat
To Display Temperature
Setting.
Press or once to
display present tempera-
ture setting. After approxi-
mately five seconds, the
thermostat displays current time and room temperature.
To Make a Temporary
Temperature Change.
a. Press or until
desired temperature
is displayed.
b. TEMPORARY is
displayed. The
TEMPORARY
change is in effect
until the next
program period.
NOTE: To cancel your TEMPORARY change, press
until End is displayed.
To Use Hold Function.
To hold the thermostat at one temperature indefinitely,
program both WAKE and SLEEP to the same
temperature.
Installer Setup
The following instructions provide the information necessary
to change the heating cycle rate, select either Fahrenheit
(F °) or Celsius (C °) and 12- or 24-hour clock format.
NOTE: To exit at any time, press until End is displayed.
1. Enter Installer Setup.
a. Use or keys
to set the
temperature set-
point to 52°F (11°C).
b. After the thermostat
reverts back to
displaying room
temperature
(approximately
five seconds),
simultaneously
press and keys
and hold for three
seconds. Release
the keys after the
display changes.
c. Press within
five seconds.
2. Select Cycles Per Hour.
The display changes to
show current cycle
rate setting.
a. Use or to
select 1, 3, 6, or 9 cph.
Refer to Table 4.
Table 4. Heating Cycle Options
M12522
M12511
System
Program
Setting
(cph)
Steam, Gravity 1
Hydronic Heat, Condensing Gas Furnaces 3
Gas or Oil Forced Air 6
Electric Heat 9
SET
AM
M12512
SET
AM
M12513
TEMPORARY
AM
M12514
SET
AM
M12518
TEMPORARY
AM
M12519
M12520
M12504
M12521

T8700B,C AN ELECTRONIC ROUND PROGRAMMABLE THERMOSTAT
68-0197—1
9
OPERATION
Zero Droop Performance
The T8700 Thermostat can control temperature closer to
setpoint than electromechanical thermostats. This is because
proportional plus integral control (P + I) maintains a constant
indoor temperature independent of the outdoor temperature.
This feature allows the T8700 Thermostat to provide tight
temperature control with virtually no noticeable swings in
temperature, a condition referred to as
droop . This zero droop
performance provides improved comfort and occupants do not
need to continually adjust thermostat settings to be
comfortable, even during extreme weather.
Power Stealing
The T8700 Thermostat steals power through the heating and/or
cooling system controls; therefore, it can be used in applications
where it is not possible to run additional wires. See Fig. 15.
The T8700 Thermostat requires only 2.5 mA of load current
when the heating and/or cooling is on. When the heating and/or
cooling is off, the thermostat operates at 0.1 mA.This low
current draw allows the T8700C to be used with most 24V
heating and/or cooling systems.
The T8700 Thermostat operates only when mounted on the
wallplate with 24V applied. Batteries are not required for
operation. Temperature setpoints, programming and
configuration settings are retained permanently in memory.
Sequence of Operations
The Heat and Cool outputs are transistor controlled. A loss of ac
power or a change in the System switch setting can turn off
outputs.Table 5 shows the Fan and System sequence of
operations.
Fan Control
The FAN switch settings for the T8700B1015 with Fan and
T8700C are ON and AUTO.
ON: The fan runs continuously.
AUTO: In cooling, the fan starts and stops with the cooling
equipment. In heating, the fan starts a few minutes after
the heating equipment turns on. With the Fuel switch in
the E position for electric heat, the fan starts and stops
with the heating equipment.
Heat Mode
With the T8700 system switch in the HEAT position, the
thermostat controls the heating system. On a call for heat, the
W terminal is energized and a flame icon shows on the
digital display.
If the Fuel switch is in the E position, both the W and G
terminals are energized on a call for heat.
Cool Mode
With the T8700C System switch in the Cool position, the
thermostat controls the cooling system. On a call for cool,
the G and Y terminals are energized and a snowflake icon
shows on the digital display. A flashing snowflake indicates
that the minimum-off timer is in effect.
Minimum Off-Timer T8700C
A minimum off-timer for the T8700C assures that the cooling
compressor does not come on again for at least five minutes
after it turns off. The minimum-off timer is triggered when the
compressor turns off or when the System switch is changed.
If the compressor turns off when the setpoint is changed, the
minimum-off timer is triggered. Power interruption and power
restoration also trigger the minimum off-timer.
Fig. 15. T8700C power stealing internal schematic.
L1
(HOT) L2
1
1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
SYSTEM SWITCH
FAN SWITCH
AUTO
ON
OFF
HEAT
COOL
Y
W
G
R
FAN RELAY
COOL RELAY
HEAT RELAY
POWER
SUPPLY
LOGIC AND
CONTROL
THERMOSTAT
LOGIC
THERMISTOR
SENSOR
M10360
MOSFET
MOSFET

T8700B,C AN ELECTRONIC ROUND™ PROGRAMMABLE THERMOSTAT
68-0197—1 10
Table 5. Sequence of Operations.
a When fuel switch is in the E position. (T8700B with Fan and T8700C).
bT8700C only.
Fan Switch Settings System Switch Settings Call for Action Energize Terminals Display Icons
AUTO OFF None None None
ON Any Any G None
AUTO COOLbCoolingbG, Y
AUTO HEAT Heating W,Ga
CHECKOUT
Heating (T8700B,C)
1. Slide the System switch to HEAT and the Fan switch to
AUTO. (For T8700B1007 Heat Only model, a Fan switch
is not an option).
2. Press and hold the key to raise the temperature
setting several degrees above the room temperature
the heating equipment should start. In conventional
systems, the system turns on the fan through a limit
control. When using the thermostat with the fuel switch
set to the E position for electric heat, the fan starts
immediately.
3. Press the key to lower the temperature setting below
the room temperature. Heating equipment should stop.
Cooling (T8700C)
CAUTION
Equipment Damage Possible.
Operating at too low of an outdoor temperature
can cause compressor damage.
Do not attempt to operate cooling when outdoor
temperature is below 50°F (10°C). Refer to
manufacturer recommendations.
IMPORTANT
A mimimum off-timer for the T8700C assures that the
cooling compressor does not come on again for at
least five minutes after it turns off. The minimum-off
timer is triggered when the compressor turns off or
when the System switch is changed. If the compressor
turns off when the setpoint is changed, the minimum-
off timer is triggered. Power interruption and power
restoration also trigger the minimum off-timer.
1. Slide the System switch to COOL and the Fan switch to
AUTO.
2. To start the cooling equipment, press the key to
lower the temperature setting several degrees below
room temperature.The fan starts and stops with the
cooling equipment.
3. Press the key to raise the temperature setting above
the room temperature. Cooling system should shut down.
Fan (T8700B1015 with Fan, T8700C)
1. Slide the System switch to OFF and the Fan switch to
ON. The Fan should run continuously.
2. Slide the Fan switch to AUTO. In heating, the fan is
controlled directly by the heating equipment and starts
a few minutes after the heating equipment turns on (for
most systems). When using the thermostat with the
Fuel switch set to the E position for electric heat, the fan
starts and stops with the heating equipment. In cooling,
the fan starts and stops with the cooling equipment.
Make certain all equipment responds properly to the
thermostat.