Honeywell VisionPRO 8000 User manual

62-0266
VisionPRO®8000
Thermostats
INSTALLER SETUP AND
SYSTEM TEST POCKET
GUIDE
62-0266.fm Page 1 Thursday, September 18, 2008 11:25 AM

62-0266 2
INSTALLER SETUP
1. Press SYSTEM.
2. Press and hold these two blank buttons until the
display changes.
SCHED HOLD
FAN
ON
AUTO
AM
SYSTEM
HEAT
Inside
M24079
DONE CANCEL
SYSTEM
HEAT
M24080
62-0266.fm Page 2 Thursday, September 18, 2008 11:25 AM

3 62-0266
3. Use arrows to change settings as required.
4. Press DONE to exit and save settings.
INSTALLER SETUP FUNCTIONS
Available option and default settings vary by
thermostat.
Table 1. Installer Setup .
Installer
Setup
Number
Installer
Setup
Name
Default
Setting All Settings Notes
0120 Date (Year
Upper)
20 20—20xx
21—21xx
Available year
range: 2001 - 2178
0130 Date (Year
Lower)
04 00-99 Available year
range: 2001 - 2178
0140 Date
(Month)
61-12
0150 Date (Day) 15 1-31 (Month Dependent)
0160 Schedule
Options
4 0—Non-Programmable
4—Programmable
DONE
PRESS TO
SELECT FUNCTION
FUNCTION SETTING
PRESS TO
CHANGE SETTING
M24082A
62-0266.fm Page 3 Thursday, September 18, 2008 11:25 AM

62-0266 4
0170 System
Selection
8 1—1H/1C Conv
2—1H/1C HP
3—1H w/o fan
4—1H with fan
6—1C
7—2H/1C HP
8—2H/2C Conv
9—2H/1C Conv
10—1H/2C Conv
11—2H/2C HP
12—3H/2C HP
0175 TOD/
Economizer
output
(terminal A)
0 0—Unused
1—TOD
2—Economizer
Economizer
energizes A during
a call for cool.
TOD energizes A
during Occupied
period, and
de-energizes A
during Unoccupied.
0180 Heat Fan
Operation
0 0—Fossil
1—Electric
Only shown for
conventional
system with heat
stages and fan
capability selected.
If heat pump is
selected, fan
defaults to electric.
0185 Pre-
occupancy
Purge
Duration
0 0—no duration
1—one hour
2—two hours
3—three hours
Shown only if
system has fan and
schedule
programmable.
Pre-occupancy
purge enabled by
nonzero duration
(and sends
economizer to
minimum position).
0190 Reversing
Valve
O/B
0 0—O (O/B On Cool)
1—B (O/B On Heat)
Only shown with
heat pump system
selected.
0220 Cycles Per
Hour (CPH)
for first stage
compressor
3 1-6 Only shown for
system with cool
stages. Selection in
this stage changes
default CPH of
second stage cool.
Table 1. Installer Setup (Continued).
Installer
Setup
Number
Installer
Setup
Name
Default
Setting All Settings Notes
62-0266.fm Page 4 Thursday, September 18, 2008 11:25 AM

5 62-0266
0230 CPH for
second
stage
compressor
3 1-6 Only shown if two
stages of cool
selected.
0240 CPH for first
stage
conventional
heat
5 1-12 Only shown if
system is
conventional with
heat stages.
Selection in this
stage changes
default CPH of
second stage heat.
0250 CPH for
second
stage
conventional
heat
9 1-12 Only shown with at
least two stages
conventional heat
or 2H/1C heat
pump selected.
0260 CPH for third
Stage Heat
9 1-12 Only shown if 3H/
2C heat pump is
selected.
0270 CPH for
Auxiliary
Heat
9 1-12 Only shown if multi-
stage heat pump is
selected (heat
pump with more
heat than cool
stages).
0280 Continuous
Backlight
0 0—No
1—Yes
Always shown. If
AC power not
present the option
is overridden and
normal backlight
operation occurs.
0300 Changeover 1 0—Manual
1—Auto
Only shown if
system has both
heat and cool
stages.
0310 Deadband 3° F
(2° C)
2 (1.5)—2° F (1.5° C)
3 (2.0)—3° F (2.0° C)
4 (2.5)—4° F (2.5° C)
5 (3.0)—5° F (3.0° C)
6 (3.5)—6° F (3.5° C)
7 (4.0)—7° F (4.0° C)
8 (4.5)—8° F (4.5° C)
9 (5.0)—9° F (5.0° C)
Only shown if
Automatic
Changeover
Selected
Table 1. Installer Setup (Continued).
Installer
Setup
Number
Installer
Setup
Name
Default
Setting All Settings Notes
62-0266.fm Page 5 Thursday, September 18, 2008 11:25 AM

62-0266 6
0320 Temperature
Indication
Scale
0 0—° F
1—° C
0330 Daylight
Saving
2 0—Disabled
1—Enabled (US 1987)
2—Enable (US 2007)
3—Enabled (Europe)
0340 Remote
Temperature
Sensor
0 0—None
1—Outdoor for Display
2—Outdoor for Control
3—Remote 10K Indoor
4—Remote 20K Indoor
Averaging would
not include on-
board sensor. It is
accomplished by
series/parallel
combinations.
2 applies only to
Heat Pump
applications
(allowing
compressor lockout
while displaying
temperature).
0350 Heat Pump
Compressor
Lockout
0 0—None
15(-9.5)—15° F (-9.5° C)
20(-6.5)—20° F (-6.5° C)
25(-4.0)—25° F (-4.0° C)
30(-1.0)—30° F (-1.0° C)
35(1.5)—35° F (1.5° C)
40(4.5)—40° F (4.5° C)
45(7.0)—45° F (7.0° C)
Only shown for
heat pump systems
with more heat
stages than cool
selected and
remote sensor
selection is outdoor
for control.
Must enforce a
dead band
between this and
Auxiliary Lockout
0360 Heat Pump
Auxiliary
Lockout
0 0—None
40(4.5)—40° F (4.5° C)
45(7.0)—45° F (7.0° C)
50(10.0)—50° F (10.0° C)
55(13.0)—55° F (13.0° C)
60(15.5)—60° F (15.5° C)
Only shown for
heat pump systems
with more heat
stages than cool
selected and
remote sensor
selection is outdoor
for control.
Must enforce a
dead band
between this and
Heat Pump
Compressor
Lockout.
Table 1. Installer Setup (Continued).
Installer
Setup
Number
Installer
Setup
Name
Default
Setting All Settings Notes
62-0266.fm Page 6 Thursday, September 18, 2008 11:25 AM

7 62-0266
0535 Temporary
Occupied
Duration
Limit
3 0—no duration
1—one hour
2—two hours
3—three hours
4—four hours
0 means no limit
0540 Number of
Periods
4 2—2 Periods
4—4 Periods
Does not appear if
Non-programmable
is chosen.
Applies to all days
of the week. With 2
selected the
“Cancel Period”
option does not
appear on the
display.
0580 Minimum
Compressor
Off Time
50—Off
2—2 minutes
3—3 minutes
4—4 minutes
5—5 minutes
Only shown if
system has cool
stages.
0600 Heat
Temperature
Range Stops
90 40 to 90° F (4 to 32° C) Only shown if
system has heat
stages.
0610 Cool
Temperature
Range Stops
50 50 to 99° F (10 to 37° C) Only shown if
system has cool
stages.
0640 Clock
Format
12 12—12 Hour
24—24 Hour
0650 Extended
Fan-on time
Heat
00—Off
90—90 seconds
Not displayed with
fan set to fossil or
with cool-only
systems
0660 Extended
Fan-on time
Cool
0 0—Off
40—40 seconds
Only shown if
system has cool
stages.
Table 1. Installer Setup (Continued).
Installer
Setup
Number
Installer
Setup
Name
Default
Setting All Settings Notes
62-0266.fm Page 7 Thursday, September 18, 2008 11:25 AM

62-0266 8
0670 Keypad
Lockout
0 0—Unlocked
1—Partial Lockout 1
2—Partial Lockout 2
3—Fully Locked
Unlocked: All
functions
accessible.
Partial 1: Locks all
but Holiday,
Override, and Up/
Down.
Partial 2: Locks all
but Holiday and
Override.
Full: Entire
interface locked/
non-functional.
0680 Temperature
Control Heat
2 1—Less Aggressive
2—Standard
3—More Aggressive
Only shown if
system has heat
stages.
Only integral gains
affected. Affects
control operation in
all control regimes
(not just recovery
or setpoint
change).
More Aggressive
stops signal prior to
reaching the
setpoint. (For use
with oversized
equipment.)
0685 Recovery
Heat Ramp
Rate
5 0-20° F/hour
(-18- -7° C)
Only shown if
system has heat
stages.
0 disables ramped
recovery (step
setpoint change at
period start time).
Table 1. Installer Setup (Continued).
Installer
Setup
Number
Installer
Setup
Name
Default
Setting All Settings Notes
62-0266.fm Page 8 Thursday, September 18, 2008 11:25 AM

9 62-0266
0690 Temperature
Control Cool
2 1—Less Aggressive
2—Standard
3—More Aggressive
Only shown if
system has cool
stages.
Only integral gains
affected. Affects
control operation in
all control regimes
(not just recovery
or setpoint
change).
More Aggressive
stops signal prior to
reaching the
setpoint. (For use
with oversized
equipment.)
0695 Recovery
Cool Ramp
Rate
3 0-20° F/hour
(-18- -7° C)
Only shown if
system has cool
stages.
0 disables ramped
recovery (step
setpoint change at
period start time).
0700 Temperature
Display
Offset
0 -3 (-1.5)— -3° F (-1.5° C)
-2 (-1.0)— -2° F (-1.0° C)
-1 (-0.5)— -1° F (-0.5° C)
0 (0.0)—0° F (0.0° C)
1 (0.5)—1° F (0.5° C)
2 (1.0)—2° F (1.0° C)
3 (1.5)—3° F (1.5° C)
This offset applies
to both the control
temperature and to
the display
temperature for
indoor sensor (and
remote indoor
sensor).
0710 Restore
Factory
Defaults
0 0—No
1—Yes
Resets all ISU
parameters to
default values and
resets the schedule
to default Energy
Star. Retains only
calendar settings
and time.
Table 1. Installer Setup (Continued).
Installer
Setup
Number
Installer
Setup
Name
Default
Setting All Settings Notes
62-0266.fm Page 9 Thursday, September 18, 2008 11:25 AM

62-0266 10
INSTALLER SYSTEM TEST
The installer Test is part of the Installer Setup Menu.
1. Enter the installer System Test by entering the
Installer Setup and pressing repeatedly
until “Test” appears.
2. Use arrow to change test and system status as
required.
3. Press DONE to exit.
DONE
M24083
DONE
PRESS TO
CHANGE STATUS
PRESS TO
SELECT TEST
M24085
TEST NUMBER SYSTEM STATUS
62-0266.fm Page 10 Thursday, September 18, 2008 11:25 AM