Honeywell VisionPRO Series User manual

VisionPRO®Series
User Guide

Welcome
Congratulations on your purchase of a
Honeywell touch screen programmable
thermostat.

133-00074EA—01
Features of your VisionPRO thermostat
Your new thermostat provides:
• Adaptive Intelligent Recovery—over time, the VisionPRO thermostat
“learns” how long it takes your system to reach the temperature you
want. It turns on the heating or cooling system earlier to make sure you’re
comfortable at the time you expect.
• Vacation and holiday scheduling—allowing you to program a setback
temperature to save energy while you are away.
• Keypad lockout to prevent unauthorized changes.
• Equipment status—provides on/off status of all equipment controlled by
the thermostat.
• Preferences—allowing you to customize the thermostat to your desired
settings.

33-00074EA—01 2
Programming and Operation
Quick reference........................................... 3
Setting the time/date................................... 5
Setting the fan............................................. 6
Setting system mode .................................. 7
Adjusting program schedules...................... 8
Schedule overrides ................................... 11
Menu Options
Viewing equipment status......................... 12
Setting vacation and events...................... 13
Setting preferences................................... 18
Cleaning the thermostat screen................ 19
Security settings........................................ 20
Advanced features .................................... 21
Appendices
Installer options......................................... 22
Replacing batteries ................................... 23
VisionPRO® Auto-Azan Overview ............ 24
Troubleshooting......................................... 26
Table of contents

333-00074EA—01
Quick reference: residential use
HOME. Touch to display Home screen.
FAN. Select fan mode.
SYSTEM. Select system mode (Heat/Cool).
MENU. Touch to display options. Start here to set
a program schedule.
Current status. Shows system mode (heat/
cool).
Current schedule. Touch an arrow to change
temperature setting and select a Temporary or
Permanent Hold.
Indoor conditions. Shows indoor temperature.
Current time. Touch to set the current time/date.
Alert Light. On when alert message is
active or system is set to EmHeat. Flashes
for battery-only power; on continuous if
system powered.
The screen lights when you
press any button. It stays lit for
7 seconds after you complete
changes. Depending on how your
thermostat was installed, the
screen light may always be on.

33-00074EA—01 4
Quick reference: commercial use
HOME. Touch to display Home screen.
FAN. Select fan mode.
SYSTEM. Select system mode (Heat/Cool).
MENU. Touch to display options. Start here to set a
program schedule.
Current status. Shows system mode (heat/cool).
Override. Touch to override program schedule.
Current schedule. Touch an arrow to change
temperature setting and set a temporary hold.
Current program status.
Indoor conditions. Shows indoor temperature.
Current time. Touch to set the current time/date.
Alert Light. On when alert message is active
or system is set to EmHeat. Flashes for battery-
only power; on continuous if system powered.
Micro SD Card port. Use card to load holiday
schedules and custom events.
The screen lights when you
press any button. It stays
lit for 7 seconds after you
complete changes. Depending
on how your thermostat was
installed, the screen light may
always be on.

533-00074EA—01
Setting the time/date
1 Touch the current time. The screen
displays Select Option.
2 Touch Time or Date, then touch Select.
3 Touch sor t until the proper time/date
is displayed.
4 Touch Done to save or Cancel to ignore
changes.
5 Touch Home to redisplay the Home
screen.
NOTE: The date is not shown on the
home screen; however, it should be set
to allow the thermostat to adjust time
automatically. (no Daylight savings time)
MCR35578
MCR34155
Select Option
Time Date
MCR34094
Please Set Time
6:30 PM

33-00074EA—01 6
Setting the fan
1 Touch FAN to display fan settings.
2 Touch On, Auto, Circ, or Follow Schedule.
3 Touch Done to save and exit.
On: Fan is always on.
Auto: Fan runs only when the heating
or cooling system is on.
Circ: Fan runs randomly about 35% of
the time (residential use only).
Follow Schedule: Fan controlled by
program (see pages 8 – 11 ).
NOTE: In commercial use,
touch Auto or On to temporarily
override the programmed fan
schedule.
MCR34096
MCR34097
On Auto Circ

733-00074EA—01
Setting system mode
1 Touch SYSTEM to display system
settings.
2 Touch desired option:
Cool: Controls only the cooling
system.
Off: Cooling system is off.
3 Touch Done to save and exit.
MCR35497
Cool
Off
MCR34098

33-00074EA—01 8
Adjusting program schedules
1 Touch MENU.
2 Select Edit Schedule to display Use
Scheduling Assistant?
• Touch Yes to create a schedule by
answering simple questions.
• Touch No to manually create a
program schedule. See page 9.
NOTE: To reduce costs, use the pre-
set Energy Saver settings.
MCR34100
MCR34101
Edit Schedule
View Schedule
MCR34102
Use Scheduling
Assistant?