Honeywell Zio TR70 User manual

SPECIFICATION DATA
63-1322-02
Zio®/Zio Plus LCD Wall Modules
TR70, TR71, TR75 WITH Sylk®Bus
GENERAL
The TR70 Series Zio (TR70/TR70-H, TR71/TR71-H) and Zio
Plus (TR75/TR75-H) are 2-wire, non-polarity sensitive, Sylk
bus communicating wall modules for use with Spyder®and
ComfortPoint™ programmable controllers.
All models have a space-temperature sensor, network bus
jack, and an LCD panel with three softkeys and two Up/Down
adjustment keys. The TR7-H, TR71-H and TR75-H models
include an onboard humidity sensor.
NOTE: Refer to the Zio/Zio Plus LCD Wall Modules Oper-
ating Guide (form 63-2719) for information about
customizing the wall module configuration in the
WEBs-AX Workbench, such as modifying the
default Home screens or creating your own appli-
cation.
FEATURES
The TR70 Series wall modules include:
• Ability to control tenant access to controller
parameters via password protection.
• Ability to assign labels for enumerated values.
• Customized parameter access, by using the Honeywell
WEBs-AX Workbench tool.
• Ability to link setpoint limits to a network variable.
• Programmable for: Home screen options, tenant
access, contractor access, optional password
protection to contractor mode, access to controller
parameters, setpoint, override, fan, and other
parameters.
• Ability to access and adjust most parameters in the
programmable controller.
• TR75 can access and adjust the controller schedule.
• Ability to balance the VAV system from the wall
module.
• Home screen can display one to three of any of the
following parameters: Temperature Setpoint, Room
Temperature, Room Humidity, Outdoor Humidity,
Outdoor Temperature, and Time, or one of virtually any
parameter in the controller.
•Networkbusjack.
• Simple 2-wire terminal connection to the
programmable controller (includes power) and an
optional 2-wire terminal connection for the network. All
connections are polarity insensitive.
• Permanent retention of user configuration, including
setpoints after a power outage.
* Support for up to four TR71 and/or TR75s per Spyder, and if
a TR70 is present, a maximum of three Zios (any combina-
tion of models) are allowed.
Table 1. TR70 Series Features.
Features
Zio
TR70
Zio
TR71
Zio Plus
TR75
Scheduling x
Parameter Memory (bytes) 1K 2K 4.9K
Up to four Zios on Sylk x* x x
Enumerated Values x x
Setpoint Limits as NVs – linking
now possible
xx
System and Fan command as NVs x x
Password protection x x
Firmware version/model visible on
display
xx
0.5 and 5 value increments x x
"-" and "/" characters in parameter
names
xx

ZIO®/ZIO PLUS LCD WALL MODULES
63-1322—02 2
SPECIFICATIONS
Compatibility: Full feature set, including scheduling and
password protection requires the latest Spyder firmware
(field upgradeable with Spyder Flash Tool), Spyder Tool
version greater than 5.18, and WEBs-AX Workbench ver-
sion 3.4.57 or greater.
Construction: Two-piece construction, cover and internally
wired subbase. Field wiring, 18 to 24 AWG (0.82 to 0.20
sq. mm), connects to a terminal block in the subbase.
Mounting Options: The LCD wall modules can be mounted
on a standard two by four inch junction box or on a 60 mm
diameter junction box. The modules may be mounted up to
200 ft. (61 m) from the programmable controller. Twisted
pair wiring is recommended for distances longer than 100
ft. (30.5 m).
Dimensions (H/W/D): See Fig. 2 on page 2.
Environmental Ratings:
Operating Temperature: 30°F to 110°F (-1°C to 43°C)
Shipping Temperature: -40°F to 150°F (-40°C to 65.5°C)
Relative Humidity: 5% to 95% non-condensing
Temperature Setpoint Range: Default range is 55°F to 85°F
(10°C to 35°C); configurable for other ranges.
Temperature Sensor Accuracy: ±0.36°F at 77°F (±0.2°C at
25°C)
Humidity Sensor Accuracy (TR71-H/TR75-H only): ±5%
RH from 20% to 80% RH
Power: 18 Vdc power is supplied to the wall module from the
2-wire S-BUS connection to the programmable
controller.
Accessories: 50007298-001 (pack of 12) medium, cover
plate; 6-7/8 x 5 in. (175 x 127 mm).
Approvals:
CE; UL94-HB plastic enclosure; FCC Part 15,
Class B
Terminal Wiring Location
Fig. 1 illustrates the location of the terminal block and other
features on the TR70 Series wall modules.
Fig. 1. LCD wall module components (rear view).
NOTE: 18 Vdc power for the LCD wall modules is sup-
plied from the programmable controller.
Module Dimensions
Fig. 2. Wall module dimensions in inches (mm).
Communications
The wall modules use a sensor bus (S-BUS) for
communications with the programmable controller.
For network communication, the building’s LON or BACnet®
network wires connect to the two terminals (NET-1 and NET-
2). See Fig. 1. A network bus port is accessible at the bottom
of the wall module by removing the jack plug.
The network bus and S-BUS terminals (see Fig. 1) are
insensitive to polarity, minimizing installation errors due to
mis-wiring. The recommended wire size for the network bus
M27349
SLOTS FOR SUBBASE
LOCKING TABS (X4)
01234
98765
WALL MODULE BUS
ADDRESS DIAL
(DEFAULT SETTING = 1)
S-BUS PROGRAMMABLE
CONTROLLER CONNECTION
NETWORK BUS
CONNECTION
EACH OF THE TWO WIRE CONNECTIONS FOR THE S-BUS AND NETWORK
BUS TERMINALS ARE POLARITY INSENSITIVE.
1 2 3 4
1
1
50028668-XXX
4321
S-BUS
S-BUS
NET-2
(optional)
NET-1
(optional)
TR70-H
YY WK
HONEYWELL
PATENT PENDING
GOLDEN VALLEY,MN
ASSEMBLED IN MEXICO
3 5/16 (84)
4 5/8
(117)
15/16
(24)
M27347

ZIO®/ZIO PLUS LCD WALL MODULES
363-1322—02
and S-BUS is 18-24 AWG (0.82 to 0.20 sq mm) depending on
application, plenum or non-plenum rated, unshielded, twisted
pair, solid conductor wire.
LCD Display
The LCD display may be customized for tenant and contractor
users. The following are a few samples of the various Home
screens that are configurable for the LCD Wall Modules. Not
all possible Home screens are illustrated here. There are
many other configurable Home screens.
NOTES:
1. Home screens can display one to three of any of
the following parameters: Temperature Setpoint,
Room Temperature, Room Humidity, Outdoor
Humidity, Outdoor Temperature, and Time, or one
of virtually any parameter in the controller.
2. Refer to the Zio/Zio Plus LCD Wall Modules Oper-
ating Guide (form 63-2719) for information about
customizing the wall module configuration in the
WEBs-AX Workbench, such as modifying the
default Home screens or creating your own appli-
cation.
Sample Tenant LCD Displays
The Fan and Occupied settings are optional for Home screen
setup. If there are no parameters configured for Tenant
access, the “View More” softkey does not display on the
Tenant Home screen.
Fig. 3. Sample Tenant Home screen with System Status,
Setpoint, Outside Temperature, and
Room Temperature (predominant).
Fig. 4. Sample Tenant Home screen with Room
Temperature and Time (predominant).
Fig. 5. Sample Tenant Home screen with
Setpoint display only.
Fig. 6. Sample Tenant “View More” display showing
CO2sensor value from controller.
NOTE: Any configured parameter may be displayed.
Sample Contractor LCD Displays
The Contactor mode allows advanced options using the
softkeys. Contractor mode also allows for customizing the
Tenant view, including setting the tenant’s Home screen and
“View More” access.
Fig. 7. Sample Contractor Home screen display with
System Status, Setpoint, Outside Temperature,
and Room Temperature (predominant).
CONTACTOR HOME SCREEN SOFTKEYS
The three softkeys on the Contractor Home screen (Fig. 7)
provide the following:
SET HOME SCREEN - allows the contractor to choose
among multiple Home screen options for the tenant.
M27354
M27379
M27377
M27356
M27357

ZIO®/ZIO PLUS LCD WALL MODULES
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com
® U.S. Registered Trademark
© 2011 Honeywell International Inc.
63-1322—02 M.S. Rev. 12-11
Printed in United States
SET VIEW MORE - allows the contractor to give additional
parameter access (view only or adjustable) to the tenant.
PARAMETERS - allows the contractor to monitor and/or
adjust parameters in the programmable controller.
Fig. 8. Sample Contractor parameter display showing
user-created discharge air parameter value.
Fig. 9. Sample Contractor parameter display showing
sensor setpoint value (CO2sensor from controller).
NOTE: Any configured parameter may be displayed.
TYPICAL SPECIFICATION
1. The wall module shall have an LCD display.
2. The wall module shall have a customizable home
screen:
a. Shall have the option to show up to 3 parameter
values on a single display.
b. Shall have the option to show occupied status.
c. Shall have the option to show system status.
d. Shall have the option to show fan status.
e. Shall have the option to show up to three of the fol-
lowing parameters:
• room temperature, setpoint, outside
temperature, room humidity, outside humidity,
time of day.
f. Shall have the option to show on the home screen
any single parameter in the controller, with a user
defined 8 letter name.
3. The wall module shall offer access to all parameters
necessary to balance a VAV system.
4. The wall module shall offer the ability to restrict access
to parameter information with keypad enabled lock out
and with optional 4 digit password protection (password
on TR71 and TR75 only).
5. The wall module shall retain user configuration including
setpoints after power outage.
6. The wall module shall use a two wire polarity insensitive
connection for all communication and power needs.
7. The wall module shall offer the ability to access and
adjust virtually all controller parameters.
8. The wall module shall offer the ability for the tenant to
adjust override time period within the limits set by the
contractor.
9. The wall module shall offer a communication jack for
remote access to the network.
10. The wall module shall offer a ± 5% on board humidity
sensor (TR70-H, TR71-H, and TR75-H only).
11. The wall module shall be configured through the Honey-
well WEBs-AX Workbench tool.
12. The wall module shall communicate with other devices
using the Sylk bus protocol.
13. The wall module shall be compatible with LON and
BACnet controllers.
14. The wall module shall offer the ability to view/edit the
controller's schedule (TR75 only).
15. The wall module shall have the ability to display enu-
merated values as text.
16. The wall module shall have the ability to use the value of
a parameter as the upper or lower limit of another
parameter (TR75 only).
ComfortPoint™ is a trademark of Honeywell International Inc.
LONMARK® is a trademark of the LonMark Association.
BACnet® is a registered trademark of BACnet International.
Spyder® is a registered trademark of Honeywell International Inc.
Sylk® is a registered trademark of Honeywell International Inc.
Zio® is a registered trademark of Honeywell International Inc.
M27358
M27359