Honeywell EXWJ400-10A User manual

- 1 -
EXWJ400-10A
MANUAL
Explosion proof Washer Pump

- 2 -
Important Safety Instructions
1. Install and use this system after reading these instruction thoroughly.
2. Keep these instructions.
3. Install in accordance with the manufacture’s instruction.
4. Take care of all Cautions and Warnings.
5. Use stainless steel hardware to fasten the mount to outdoor surfaces.
6. A readily accessible disconnect device shall be incorporated in the building installation
wiring.
7. Only use replacement parts recommended by Honeywell.
8. The maximum ambient temperature range is -20℃to 60℃.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER(OR BACK).
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PRERSONNEL
Explanation of Graphical Symbols.
This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important
operating and maintenance(Servicing) Instructions in the literature
accompanying the appliance.
TO REDUCE THE RISK OF IGNITION DO NOT OPEN WHEN AN EXPLOSIVE
GAS ATMOSPHERE MAY BE PRESENT
WARNING: To reduce the risk of ignition of Hazardous Atmospheres, disconnect
the equipment from the supply circuit before opening.

- 3 -
Methods of Application
WARNING: Gross weight of this system is about 12kg.
It is recommended you to wear proper non-slip gloves during installation.
This system can be installed in a standard as below Figure1.
If you wish to install another method, you must do it after discussing with a
manufacture. And please refer to 7page for wiring cable connection with the
NEXPTZ Camera Series which can be applied.
Figure1.
Standard Method of Installation with
NEXPTZ or NEXH camera Series
EXWJ400-10A
NEXPTZ Camera
OR
NEXH Camera

- 4 -
Components and Specification
a. Case
b. Washer tank
a. Washer pump external Case
Washer pump Case
Material
SUS316
Thickness
1.2mm
Size
380(W
) x 420(H) x190(D) (mm)
Weight
6.8kg
Washer Tank
Material
PE
Size
235(W)x 294(H
) x157(D)
(mm)
Water Capacity
10L
b . Washer Tank
c . Nozzle
Nozzle
Material
SUS316
Angle
Ø 0.5(Spread Aangle:0
°)
c. Nozzle bracket
d. Tube
Tube
Size
Ø1/4”cm X 10m
d. Tube
<Only for NEXPTZ Camera>
WARNING: Keep at least 10% of tank filled with windshield washer to avoid device damage.

- 5 -
Components and Specification
<Key Feature>
•Explosion proof Certificated Grade
: Ex d IIC T6 / II 2 Gb
For use in variety of harsh and/or hazardous
environments, including marine environment.
•Specialized for High Speed NEXPTZ &NEXH Series.
•Easy to installation.
•Easy to clean any dried dust on the glass.
f. Pump motor & housing (EXWJ400)
f. Pump Motor & Explosive proof Housing
Explosive proof Pump Motor Housing
Material
AL6061
Thickness
10mm
Size
Ø 65mm x 188 (L)
Weight
1.0kg
IECEx/ATEX
Certification
IECEx KGS 11.0004X
ATEX LCIE 11 ATEX 3084X
IP
Grade
IP66
Operating Temp
-20℃~ 60℃
* The liquid shall be used an antifreeze to endure below zero
temperature -20℃~ 0℃.
Pump Motor
Power Supply
DC 24V 2A
Rated Voltage
DC 15V
Maximum pressure
2.0 kgf/cm2
Maximum
Capacity 1.9ℓ /min(30GPH)
Hose
Connected
Inlet
Ø 6.5
Outlet
Ø 6.5

- 6 -
EXWJ400-10A
EXWJ400-10A Schematic
CAUTION
1) If EXWJ400-10A is applied to NEXPTZ, the alarm-
out(B) can’t be used.
2) It is recommended that the washer pump tank should
be located on equal or lower (under 8m) level than the
nozzle location.
NEXH
Camera
NEXPTZ
Camera OR
POWER
AC110 or 220V
BNC
MAIN MONITOR
DATA1 DATA2
+ - -+ + -
REAR
FRONT
KEYBOARD CONTROLLER
HTX-5000
REAR
DATA 2 DATA 1 DC 12V
RS 485
1 DOME 2
IN OUT DVR RS 232C
ALARM/DVR
DC 12V
SLAVE
RS 485 +
-(Alram out B)
COM
N/O
RS 485
DVR
Check Valve
Pump
Motor
+
GND
+
GND
Input power
DC 24V

- 7 -
Water jet
①Set washing position
-.Move the window face to nozzle
by using pan/tile and save the
position on preset 59.
②Press and button.
(88+ Preset) at Pelco Protocol
- Set the specific position to wash
front window toward the nozzle on
preset 59.
-Run washing and wiping.
4
Check water level in
the tank
periodically.
Operating
[ Do following step to operate washer Pump function with NEXPTZ Camera ]
1. Save the location of nozzle position (washing) on Preset 59.
* First of all, The NEXPTZ pan/tilt direction should be decided and saved that window glass of camera housing toward nozzle
of water jet on preset 59.
2. Push The [4+On] button on HTX-5000 Keyboard.
* Push the 88+preset button at Pelco protocol.
Result : 1) Pan/Tilt’s moving to nozzle position (location Preset 59 )
2) Auto-Stop after Spray water & Wiping ( 5 sec, 6 Wiping )
3) Pan/Tilt’s moving back to the previous position
Honeywell Security Group.
Honeywell Co., Ltd.
Address : 5F, Sangam IT Tower, 434, WorldCupbur-ro
Mapo-gu, Seoul 121-835, Republic of Korea
TEL : [phone] / 6394
FAX : [phone]
E-mail: [email protected]
Printed in Korea
[ Do following step to operate washer Pump function with NEXH Camera ]
-Water will be come out from the
nozzle until Joystick back or released.
①Pull Joystick to Tilt down function.
Washer
Pump
Check water level in
the tank
periodically.

- 8 -
EXWJ400-10ADrawing

- 9 -
Prepare working
Keep at least full of between tank and motor filled with windshield washer to avoid device damage.
1. Fill tank full windshield washer. Blue ring push
and tube separation
2. Blue ring push
3. Check washer fill in between tank and motor
tube
4. Tube insert again