HopeRF HM-TRLR-EVB User manual

HM-TRLR-EVB Manual
Tel: [phone] Fax: [phone] E-mail: [email protected] http://www.hoperf.com
HM-TRLR-EVB Manual
HOPE MICROELECTRONICS CO.,LTD
Address：:2/F Building 3, Pingshan Private Enterprise ST Park,Nanshan
District, Shenzhen,Guangdong,China
Post Code：518052
components Tel：[phone]-810
RF Tel：[phone]-828
Fax：[phone]
E-mail: [e-mail]
website：http://www.hoperf.com
1

HM-TRLR-EVB Manual
Tel: [phone] Fax: [phone] E-mail: [email protected] http://www.hoperf.com
1.Instruction:
HM-TRLR-EVB is a demo board design for HM-TRLR RF module.It has
two working mode.(online and offline).When turn into online mode,the
demo board works with software TRLR-PCConfig.At this time the user can
modify the parameter and test the AT order etc.When turn into offline
mode.At this time the user can test communication and low power
consumption of the HM-TRLR-EVB demo board.
2.Features:
External interface instruction:
1
HM-TRLR-S module slot
2
HM-TRLR-D module slot
3
On-line and off-line jumper
4
Offline mode, Serial rate and parity jumper
5
mini-USB connecting seat
6
RS485 seat
7
RS232 connecting seat
8
Power switch jumper
2

HM-TRLR-EVB Manual
Tel: [phone] Fax: [phone] E-mail: [email protected] http://www.hoperf.com
3.Software HM-TRLR-PCConfig and drive installation
Please download and install HM-TRLR-PCConfig.exe and
CP210x_VCP_Win2K.exe from our website.
4.Before on-line mode please confirm jumper J2/J2/J4/J5/J3 if connect to
PC.Plug HM-TRLR RF module into demo board and through mini-USB
connect to PC.At this time open software HM-TRLR-PCConfg,As figure.
Config interface operation:
1
PC serial port and baud rate choose.
2
Valid only for setting HM-TRLR-S Series Moudle
3
RF module modulation mode choice
4
Working frequency choose ,pay attention to the working frequency.
5
Valid only for setting HM-TRLR-S Series Moudle
6
LoRa modulation, wireless baud rate
7
Write and read parameter
3

HM-TRLR-EVB Manual
Tel: [phone] Fax: [phone] E-mail: [email protected] http://www.hoperf.com
Write Operation step:
1) Choose the port of PC,baud rate and check mode .Then open the port.
2) Set the parameter of module.
3) Cleck the “Write”button. If succeed that Tx Led flickers and display
“Write Success”. If failed, display “Write Fail”.
2、Test interface operation:
1
AT command button
2
AT command test check box.
3
Hexadecimal display
4
Send data automatically add a carriage return
5
Send data content
4

HM-TRLR-EVB Manual
Tel: [phone] Fax: [phone] E-mail: [email protected] http://www.hoperf.com
AT testing step:
1) Open the port.
2) Hook on the “AT Command Test”options.
3) Write AT command in AT+COMMAND editing box and click the right
button.
Data communication test step:
1)PC connect to two HM-TRLR-Test Boards.
2)Open the serial port.
3)HM-TRLR module configuration the same parameter.
4) Cancel the “AT Command Test”options.
5)Fill send data content and click the “Send”button.
5. Off-line operation:
When in the off-line mode ,please confirm if jumper J2/J2/J4/J5/J3 connect
to EVB-side. Plug HM-TRLR module in demo board and choose the right
serial parameter in J1.
5

HM-TRLR-EVB Manual
Tel: [phone] Fax: [phone] E-mail: [email protected] http://www.hoperf.com
Baud rate jumper choose:
jumper
Baud rate
1 ○○
2 ○○
3 ○○
4 ○○
1200
1 ●●
2 ○○
3 ○○
4 ○○
2400
1 ○○
2 ●●
3 ○○
4 ○○
4800
1 ●●
2 ●●
3 ○○
4 ○○
9600
1 ○○
2 ○○
3 ●●
4 ○○
14400
1 ●●
2 ○○
3 ●●
4 ○○
19200
1 ○○
2 ●●
3 ●●
4 ○○
38400
1 ●●
2 ●●
3 ●●
4 ○○
56000
1 ○○
2 ○○
3 ○○
4 ●●
56700
1 ●●
2 ○○
3 ○○
4 ●●
115200
6

HM-TRLR-EVB Manual
Tel: [phone] Fax: [phone] E-mail: [email protected] http://www.hoperf.com
Choose the check way of port:
EVEN ○○
Odd ○○
None Check
EVEN ●●
Odd ○○
EVEN Check
EVEN ○○
Odd ●●
Odd Check
6.Working mode:
In the off-line mode, the test board has four working mode: normal mode、
transmit mode、receive mode and sleep mode.
1) Normal mode: After power on, the test board is in normal mode,The
user pressing the S1 button momentarily that make the test board send
data.When send data red led flash once.When receive data green led flash
once and buzzer beeps once.
2) Transmit mode: In the normal mode,long-pressing the S1 button and
hear the buzzer beeps twice.Then the test board entry to the transmit
mode.In the transmit mode,send the data in every three seconds.The buzzer
beeps once after receive data. When pressing the S1 button momentarily
that reback to the normal mode after buzzer beeps once.
3)Receive mode: In the normal mode,long-pressing the S2 button and hear
the buzzer beeps twice,then the test board entry to the receive mode.In the
receive mode,the buzzer beeps once after receive data and return data.When
pressing the S2 button momentarily that make it return to normal mode after
buzzer beeps once.
4) sleep mode: In the normal mode,long-pressing S1/S2 button.The test
board turn into sleep mode after buzzer beeps twice and Red/Green Led
flashed.The user can
7.Communication test:
1)Manual communication test: When two test boards into normal mode.The
user press S1 button momentarily of one test board.Another test board
beeps once after receive data.
2)Automatic communication test: When one of the test board into transmit
mode and another into receive mode,then the buzzer beeps.That means it
received data.
Pay attention: Test boards do not, turn off the power.
7

HM-TRLR-EVB Manual
Tel: [phone] Fax: [phone] E-mail: [email protected] http://www.hoperf.com
8
HOPE MICROELECTRONICS CO.,LTD
Add: 2/F, Building 3, Pingshan Private
Enterprise Science and Technology
Park, Lishan Road, XiLi Town,
Nanshan District, Shenzhen,
Guangdong, China
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Website: http://www.hoperf.com
http://www.hoperf.cn
This document may contain preliminary information and is subject to
change by Hope Microelectronics without notice. Hope Microelectronics
assumes no responsibility or liability for any use of the information
contained herein. Nothing in this document shall operate as an express or
implied license or indemnity under the intellectual property rights of Hope
Microelectronics or third parties. The products described in this document
are not intended for use in implantation or other direct life support
applications where malfunction may result in the direct physical harm or
injury to persons. NO WARRANTIES OF ANY KIND, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MECHANTABILITY
OR FITNESS FORAARTICULAR PURPOSE,ARE OFFERED IN THIS
DOCUMENT.
©2006, HOPE MICROELECTRONICS CO.,LTD. All rights reserved.