Horiba stec Mt-51 User manual

Ｍ

CODE: CSMS5101 ver1.3

1.Specifications

2.Operating Panel Side

3．Connector Side

Analog use connector: D-subminiature15 socket connector (#4-40UNC inch screw thread)

1)±15VSPEC ２）＋24ＶSPEC

4．External Dimension Drawing

5．Fixing method

6.State Transition Diagram

Attention：It goes back up in a control mode from each setting mode when it is not operated at the time of each setting morethan ten seconds.

7. Initial setting

7-1Setting of the decimal point position

Entering full scale range setting mode.Up down key▼▲ can change value

7-2 Full scalevalue setting

Setting full scale value (equivalent to full scale value of the mass flow controller).

Please set the full scale to a model becoming the use than the following procedures.

Enterring the full scale range setting mode。key can change beam.Up down key▼▲ can change value.

8. Explanation of the MFC control mode

MFC control operation mode is a mode controlling with an operation button of the entire surface.

Flow quantity control, valve compulsion are open and can perform valve forced closing.

Setting flow quantity is displayed when you input a flow quantity setting signal after power supply injection.

But there are not relations with the true flow quantity, please warn the flow quantity output indication value when a mass flow controller is not connected.

8-1 Flow rate control

In case of flow rate setting,Up down key▲▼is pressed（“Ｍode” Lights out→Lighting）It decides a flow quantity set point.In case of setting value beam is

changed key can change The flow quantity signal which was set because setting flow quantity pushes the "SET" key after a decision is input.

key can change。

8-2Valve forced opening

Open turns on by pushing "Open" of the front valve and becomes the valve forced open state.

”By long pressing “Open”,Open” become Lights out and valve Open cancel.

Priority is valve open signal whantever it input some setting.

8-3 Valve forced closing

Close turns on by pushing "Close" of the front valve and becomes the valve compulsion closing state.

By long pressing”Close”, “Close” become Lights out and valve Close cancel.

Priority is valve open signal whantever it input some setting.

9. Explanation of MFC addition mode

MFC control operation mode is addition mode with an operation button of the entire surface

It performs flow addition , stop, reset.

9-1 Addition target setting

By long pressing“Mode”、enter addition parameter mode and up down key▼▲ can set addition target setting

key can change beam

9-2 Addition start

By long pressing“Mode”、enter addition parameter mode. key long pressing andup down key▼▲

Select addition function ”YES”after that、press“SET”key.,addtion start

9-3 Additionstop/reset

"C" LED turns on when I push the "C" key during addtion, and addition stops. It becomes "C" LED lights out when I push the "C" key again, and addition is

started.

When a horizontal piece of timber does "C" key, the addition function is canceled, and the numerical value returns to 0. Because a addition value becomes 0

when the head pushes the "C" key at the time of multiplication tentativeness, "C" LED pushing C "key, please start addition in a state of lights out.

10.Communication function

10-1.Basic information

Communication protocol：Modbus RTU、

Communication level：RS232 or RS485、

Parity ：EVEN

Character bit ：8bit

Stop bit ：１bit

Error detectin ：CRC-16

Transmission rate ：4800,9600,19200bps

10-2.Connection

COMM

MFC

A+(R×D)

Chassis Ground

B-(TXD)

GDN2

INSTRUCTION MANUAL

DIGITAL READOUT AND CONTROL

MT-51

A+/RxD ：RS485 A+, RSRS232 Rxd

Chassis ：Ground

B-/TxD ：RS485 B-, RSRS232 Txd

GND2 ：COM

GDN2

Chassis

A+(R×D)

B-(TXD)

LED（Red）

Flow output value

LED（Green）

Se tup and an integrated value

LED（Green）

OpenDirections light

LED（Red）

CloseDirections light

LED（White）

ModeDirections light

LED(Orange）

C Addition stop directions light

Openkey

Close key

Set key

Up key

C Addition stop / reset key

Mode key

Change key

Down key

Wiring diagram

MFC Connection connector

Power supplies inlet

Communication connector

It changes with a power supply

and input-and-output signals.

Please connect with

an attached power

cable.

Use connector：

D-subminiature15

Socket connector

#4-40UNCInch screw

thread

A change beam flashes on and off. Full scale range range：100～5000

．

Only a decimal point position flashes on and off. Change range：0～3

Out pu flow rate

Input flow rate

"The SET" is a setting key, and setting is settled by pushing "the SET"

after setting.

Setting is canceled when I push "Mode" in the middle of setting and

returns to a value before the setting.

Set range：0～9999E6

Metal hook

Power ON

Decimal point setting

Valve compulsion Open

Open Instructions light lighting

Valve compulsion Close

Close Instructions light lighting

“Open key”long press

“Closekey”long press

MFC Control mode/Addition mode

Addition target

value setting

Full scale

range setting

Data backup

Digital communication

ON/OFF

Transmission rate

setting

Apparatus ID setting

機器 ID 設定

In valve compulsion

Open/Close,valve

voltage setting

“ ” ”Long press

“ ” Long press

Addition function

ON/OFF

A valve is in a state in

multiplication target

It is the arrival target

value RESET right or

wrong in multiplication

target valueON/OFF

Data back up

“Mode” ”Long press

“ ” Long press

“.n”display、set range 0～3

▲▼key can change

“FS” display、set range：100～5000

▲▼key can change

Number figure movement

“AUtO” display、set：YES/NO

▲▼key can change

“BAUd”display,set ：

4800,9600,19200

default＝9600

▲▼key can change

“DEU.No” display、

set range：1～247、default＝1

▲▼key can change

“H OFF”display、

YES：Open -15V; Close 15V

NO：Open ,15V; Close -15V

＊default＝NO

“q. SET” ”display、set

range：0～9999E6

▲▼key can change

“qt” ”display、set：YES/NO

▲▼key can change

“q-StP” display

YES：valve close

NO：valve normal control

▲▼key can change

“q-CLr”display、

YES：RESET

NO：NO RESET

▲▼key can change

“q SAU”display、

YES：Save addition value

in EEPROM

NO：NO save addition value

in EEPROM

▲▼key can change

“ ”Long press（Mode lighting）

“ Long press

Parameter for control

Parameter for Addition

Addition cut

value setting

“q vth” display、

set range：0～5.0%

※±Error of 0.2%

▲▼key can change

“NV bS” display、set：YES/NO

YES：Set value save

NO：Set value no save

▲▼key can change

ZERO points

adjustment

“ ” Long press

Attention:

This function is an offset adjustment function of the main body of MT51.

Therefore an indication error might occur when adjusted on

the visitor side.Please use it in a state at the time of the shipment.

“ ” Long press

Fixing hole

Dimensions of mounting holes ：

92mm×92mm

10-3．Explanation of each order

10-3-1 Read out flow value

10-3-2 Read out addition value cardinal number

10-3-3 Read out addition index

10-3-4 Read out function number

10-3-5 Write in flow value

10-3-6 Write in addition value cardinal number

10-3-7 Write in addition index

10-3-8 Write in Bit data

10-3-9 Detail of bit data

11.Factory Settings

Each Functions of the factory settings are as bellow.

Control mode parameter

・Decimal point setup：1

・Full-scale range setup：500

・Data back up：YES

・Digital communication：NO

・Transmission speed setup：9600

・Apparatus ID setup：1

・Valve voltage setup at the time of valve compulsion Open/Close.：NO

Addition mode parameter

・Addition desired value setup：9999E6

・Addition function（ON/OFF）：NO

・Valve state to an addition desired value at the time of attainment.：NO

・Desired value RESET propriety to an addition desired value at the time of attainment.：NO

・Data back up：NO

・Addition cut value setup：0.0

12.Product warranty

12-1 Period

The product is warranted for one (1) year (parts and labor) from date of shipment

Repairwill be provided free of charge during this period if the products is returned to HORIBA STEC or authorized

service representative with a description of the problem.

HORIBA STEC is not responsible for damage due to customer neglect or improper operation of this product.

12-2 Scope

Warranty coverage is restricted to this product only.HORIBA STEC is not responsible for damage to other

components due to improper operation of this product

12-3 Warranty

Replacement parts are warranted for ninety (90) days or the remainder of the warranty period(whichever is longer).

12-4 HORIBA STEC is not responsible for damage ue to:

a)Natural disasters

b)Miss-operation or abuse of this product

c)Operation or storage in an unsuitable environment

d)Operation outside of the rated specifications

e)Unauthorized alterations or retrofits to this product

Repair expense with / without charge is to be determined as examination and / or disassembly of the returned

*For questions of service please contact

Appendix : China RoHS

Meaning of Marking

标记的意义

マークの意味

Name and amount of hazardous substance used in a product

产品中有害物质的名称及含量

本标记适用在中华人民共和国销售电器电子产品，标记中央的数字表示环境保护使用期限的年数。(不是表示产

品质量保证期间。)只要遵守这个产品有关的安全和使用注意事项，从制造日开始算起在这个年限内，不会给

环境污染、人体和财产带来严重的影响。请不要随意废弃本电器电子产品。

This marking is applied to electric and electronic products sold in the People's Republic of China. The figure

at the center of the marking indicates the environmental protection use period in years. (It does not indicate a

product guarantee period.) It guarantees that the product will not cause environment pollution nor serious

influence on human body and property within the period of the indicated years which is counted from the date

of manufacture as far as the safety and usage precautions for the product are observed. Do not throw away

this product without any good reason.

本マークは、中華人民共和国で販売される電気電子製品に適用され、マークの中央の数字は環境保護使用期限

の年数を意味します（製品の品質保証期間を示すものではありません）。この製品に関する安全や使用上の注意

をお守り頂く限り、製造日から起算するこの年限内では、環境汚染や人体や財産に深刻な影響を及ぼすことはあり

ません。本製品をみだりに廃棄しないでください。

部件名称

Unit name

有害物质

Hazardous substance

铅

Lead

(Pb)

汞

Mercury

(Hg)

镉

Cadmium

(Cd)

六价铬

Hexavalent

chromium

(Cr (VI))

多溴联苯

Polybromo-

biphenyl

(PBB)

多溴二苯醚

Polybromo-

diphenyl ether

(PBDE)

外壳 Case

机械零部件 Machine parts

电路板 Printed board

本表格依据 SJ/T 11364 的规定编制。

This form is prepared in accordance with SJ / T 11364.

○:表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

Denotes that the amount of the hazardous substance contained in all of the homogeneous materials used in the component is below the limit on

the acceptable amount stipulated in the GB/T 26572.

×:表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。

Denotes that the amount of the hazardous substance contained in any of the homogeneous materials used in the component is above the limit on

the acceptable amount stipulated in the GB/T 26572.

Japan：

HORIBA STEC,CO.,LTD

11-5,Hokodate-cho,Kamitoba,Minami-ku,Kyoto,601-8116 Japan

URL http://www.horiba-stec.jp/

Manufacturer：

HORIBA Precision Instruments (Beijing) Co.,Ltd.

40,Beiyuanlu,Chouyou-ku Beijing China

URL http://www.horibaprecision.com

HORIBA STEC MT-51 User manual

Popular Digital Readout manuals by other brands