Horstmann ChannelPlus H11XL User manual

CCHHAANNNNEELLPPLLUUSSHH1111XXLL
UUSSEERRIINNSSTTRRUUCCTTIIOONNSS
BBAATTTTEERRYY
The programmer is fitted with a non-rechargeable, long life battery, which will maintain the
programmed time settings for a minimum of ten months with the supply disconnected.
THIS SHOULD BE SUFFICIENT TO COVER POWER INTERRUPTIONS DURING THE LIFE OF THE UNIT.
During power interruptions the display will be blank, after 3 days the current time of day will be lost.
If the programmer is not to be used for a long period of time, the switch on the rear of the unit
should be returned to the BATTERY OFF position. These are both to prolong the battery life.
SSEERRVVIICCEEAANNDDRREEPPAAIIRR
This programmer is NOT user serviceable. Please do not dismantle the unit.
In the unlikely event of a fault developing please refer to the RESETTING THE PROGRAMMER section of
this user guide located on page 2. If this fails to resolve the problem please contact a local heating
engineer or a qualified electrician.
QQUUEESSTTIIOONNSSAANNDDAANNSSWWEERRSS
The display only reads bAt
The unit display has become frozen
The indicator neon fails to illuminate
The indicator neon will illuminate but
the pump and/or boiler fails to
operate
There is no display on the
programmer
How do I know if the programmer is
still under warranty
How is the programmer removed from
the wall
When setting the programme times,
the setting ‘bounces’ by 10 minute
periods
Turn the battery on.The switch on the rear of the unit must be in either the Fully Pumped
or Gravity position.
This could be due to local electrical interference. Using the RESET procedure may rectify
the fault.
Using the RESET procedure may rectify the fault. If the problem persists the programmer
will need replacing.
This may indicate a problem elsewhere in your system;
E.g. A zone valve, etc. please contact a registered installer for advice.
Try the RESET procedure on page 2, if this fails to rectify the problem please have the
mains supply checked
The ChannelPlus XL range comes with a 5 year guarantee from the date of manufacture.
This date is located on the rear of the unit, indicated by a month over a year
WWAARRNNIINNGG::The ChannelPlus programmer must only be removed from it’s backplate by
either a qualified electrician or heating engineer; The programmer plugs in to a 9 pin
backplate located on the rear of the unit and is secured using 2 screws located on the top
surface of the unit. Undo these screws and pull forward and down in an arc motion
This indicates that you have reached an existing set time period, you will be unable to set
a new ON/OFF time unless there is an alteration to the existing timed period
LEAFLET No P32648
ISSUE 5 PPaaggee11
PPaaggee44
TThheeffoolllloowwiinnggaarreessoommeeoofftthheeeeaassyyttooooppeerraatteeffeeaattuurreess::--
11oorr22HHoouurrBBoooosstt..
AAddvvaanncceeccoonnttrroollggiivveessiinnssttaannttOOnn//OOffffoovveerrrriiddee
UUppttoo33OOnn//OOffffppeerriiooddssiinneeaacchh2244HHoouurrooppeerraattiioonn..
PPrrooggrraammmmeeooppttiioonnss::AAuuttoo//AAllllddaayy//OOnnccoonnssttaannttllyy//OOffff
HHoorrssttmmaannnn’’ssCChhaannnneellPPlluussHH1111XXLL--SSiinngglleeCChhaannnneellPPrrooggrraammmmeerrOffers up to
three programmed operating periods per day with independent Boost and
Advance control.
Can be used as a direct replacement for the 425 Coronet, where the load
does not exceed 3Amps and H517(Allowing for new programmer position).
LLCCDDDDIISSPPLLAAYYFFEEAATTUURREESS
1 Current TIME OF DAY
2 Switch time SETTING indicator
3 ADVANCE symbol
4 BOOST symbol
5 Current programme
6 Next switch time
LLEEDDIINNDDIICCAATTOORR
7 Circuit ON indicator
EEAASSYYTTOOUUSSEEPPRROOGGRRAAMMMMEEAANNDDFFEEAATTUURREEBBUUTTTTOONNSS
8 ADVANCE(ENTER) button
9 BOOST button
10 PLUS button - located under the cover
11 MINUS button - located under the cover
TThheeSSEELLEECCTTbbuuttttoonniissllooccaatteedduunnddeerrtthheeffrroonntt
ccoovveerr
12 SET slider switch
13 SET Positions
PROG.RUN HOLIDAY CLOCK ON/OFF TIMES
IInntteerrnnaallSSlliiddeeSSwwiittcchh--
llooccaatteedduunnddeerrffrroonnttccoovveerr
12
13
1
5
43
2
8
7
9
10
11
6
Below cover
Below cover
Horstmann Controls Limited
Bristol
BS4 1UP
Email: [email protected].uk
Website: www.horstmann.co.uk

TThheessiimmpplleeiinnssttrruuccttiioonnssbbeelloowwaarreeddeessiiggnneeddttoohheellppwwiitthhtthheepprrooggrraammmmiinnggoofftthheeuunniitt..AAlllltthheeffoolllloowwiinngg
iinnssttrruuccttiioonnssrreeqquuiirreetthheeffrroonnttffllaappttoobbeelloowweerreedd..PPlleeaasseerreeppllaacceetthheeffllaappwwhheenn
nnoorrmmaallooppeerraattiioonniissrreeqquuiirreedd..
Electronic equipment can in some circumstances be affected by electrical interference. If the
programmer’s display becomes frozen or scrambled; or if you wish to revert back to the default time
settings please use the following procedure.
FFRROONNTTCCOOVVEERR
SSEETTTTIINNGGTTIIMMEEOOFFDDAAYY
SSEETTTTIINNGGTTHHEEOONNAANNDDOOFFFFTTIIMMEESS
Should you encounter any problems, please refer to the
QQuueessttiioonnaannddAAnnsswweerrsection located on page 4
The normal working position for the SET switch is in the PROG.RUN position. In order to remind the user
of this, the flap is unable to be closed with the switch in any other position.
RREESSEETTTTIINNGGTTHHEEPPRROOGGRRAAMMMMEERR
The SET slide switch must be in the PROG.RUN position for the following instructions.
Press SELECT once.
Programme goes from
AUTO to ALL DAY
Press SELECT again.
Programme goes from
ALL DAY to ON
Press SELECT again.
Programme goes from
ON to OFF
Press SELECT again.
Programme goes from
OFF to AUTO
Unit will operate from
first ON until last OFF
period
Unit will be
continuously ON
Unit will be
continuously OFF
Programmer will return
to normal ON and OFF
times
BBOOOOSSTTFFUUNNCCTTIIOONN--11oorr22hhoouurrtteemmppoorraarryyoovveerrrriiddee
Press BOOST button once:
Your System will be Boosted
for 1 hour
Press BOOST button twice:
Your System will be Boosted
for 2 hours
At any time during a BOOST
period press BOOST again to
return to normal program-
ming
AADDVVAANNCCEEFFUUNNCCTTIIOONN--BBrriinnggssffoorrwwaarrddnneexxttoonnoorrooffffooppeerraattiioonn
Press ADVANCE button once
to move to the next
ON/OFF time
To cancel the advance press the ADVANCE
button again. This will return the unit to
its normal programme
HHOOLLIIDDAAYYFFUUNNCCTTIIOONN--AAlllloowwssssyysstteemmttoobbeepprrooggrraammmmeeddffoorruuppttoo3322ddaayyss
Move SET switch to the
HOLIDAY position
Use the PLUS button to enter the
required number of nights
(MAX OF 32 NIGHTS)
Return SET switch to the
PROG.RUN position
Whilst the HOLIDAY FUNCTION is in operation the system will remain OFF, the display will show the
number of nights remaining. The HOLIDAY setting is an instant function and cannot be set in advance.
The HOLIDAY FUNCTION can be cancelled at any time by pressing any of the SELECT buttons.Normal
programme functions will resume at the first ON period after the pre-set number of nights has expired.
IINNFFOORRMMAATTIIOONNAANNDDAADDVVIICCEE
Programming ON/OFF times
If a period is not required it can be cancelled by setting the ON and OFF settings to the same
time. Example ON 10:00am OFF 10:00am
Your programmer will prevent you from accidentally overlapping ON and OFF times.
Example: If the 2nd ON time is set at 12:00pm and then you try and set the 1st OFF at 12:30 pm the
OFF setting will ‘bounce’ by a 10 minute period until the 2nd ON time has been adjusted.
08
SETTING
AUTO
ON UNTIL
11:30AM
AUTO
ON UNTIL
10:30AM
ALL DAY
ON UNTIL
8:30PM ON OFF
ADVANCE
SELECT
Lower the front flap of the unit. Press the ADVANCE and SELECT
buttons together then release the buttons and the programmer will
return to the preset factory settings.
PPaaggee22
BOOST
SSPPEECCIIAALLFFEEAATTUURREESS
PPaaggee33
10:00AM
Move the SET
switch to the CLOCK
position.
Use PLUS and
MINUS buttons to
adjust time
Return SET switch to
PROG.RUN position
12:OOPM
SETTING
1:45PM
SET
Move SET switch
to the
ON/OFF TIMES
position.
Use the PLUS and
MINUS buttons to
adjust the 1st ON
time.
Use the PLUS and
MINUS buttons to
adjust the 1st OFF
time.
Repeat this
process for 2nd and
3rd setting.
Return SET
switch to PROG.RUN
position.
Press
ENTER
Press
ENTER
SETTING 1ST
ON OFF
6:30AM 8:30AM
10:00AM 10:00AM 10:00AM
10:00AM
BOOST
1st ON 1st OFF 2nd ON 2nd OFF 3rd ON 3rd OFF
6:30 AAMM8:30 AAMM12:00 PPMM12:00 PPMM4:30 PPMM10:30 PPMM
DDEEFFAAUULLTTTTIIMMEESSEETTTTIINNGGSS
The default factory settings are shown above, however if you wish to change these proceed as
instructed below.
RESET