Horstmann CentaurStat 7 User manual

PAGE 1PAGE 4
LEAFLET No P82162
ISSUE 1
BBAATTTTEERRYYRREEPPLLAACCEEMMEENNTT
UUSSEERRSSIINNSSTTRRUUCCTTIIOONNSS
CCEENNTTAAUURRSSTTAATT77
GGEETTTTOOKKNNOOWWYYOOUURRCCEENNTTAAUURRSSTTAATT
TThheeffoolllloowwiinnggaarreessoommeeoofftthheeCCeennttaauurrSSttaattffeeaattuurreess::--
AAddjjuussttaabblleettaarrggeetttteemmppeerraattuurreessbbeettwweeeenn55ooCC--3300ooCC
TTeemmppeerraattuurreeoovveerrrriiddeeffaacciilliittyy
66SSeeppaarraatteehheeaattiinnggppeerriiooddss
TTeemmppeerraattuurreelloocckkffaacciilliittyy
77DDaayypprrooggrraammmmiinngg
CCEENNTTAAUURRSSTTAATTEELLEECCTTRROONNIICCPPRROOGGRRAAMMMMAABBLLEETTHHEERRMMOOSSTTAATTSS
can be programmed to create a comfortable yet efficient
environment in your home.
1 SET indicator
2 SET positions
3 SET button
4 OVERRIDE (MINUS) button
5 OVERRIDE (PLUS) button
6 ENTER button
7 Time or Current Temperature
display
8 Target Temperature
9 System ON symbol
10 Day of week indicator
11 PM Indicator
12 Temperature Lock Symbol
1
9
7
6
5
4
2
10
3
Horstmann Controls Limited
Bristol
BS4 1UP
Email: [email protected].uk
Website: www.horstmann.co.uk
SSEERRVVIICCEEAANNDDRREEPPAAIIRR
This product is NOT user serviceable. Please do not dismantle the unit.
In the unlikely event of a fault developing please refer to the RESETTING THE PROGRAMMER section of
this user guide located on page 2. If this fails to resolve the problem please contact a local heating
engineer or a qualified electrician.
Your CentaurStat is battery operated. The batteries
supplied with the unit should last for approximately two
years.
When the batteries are nearing the end of their life a
BATTERY LOW symbol will flash on the display
(see diagram opposite).
automatically return to your CentaurStat.
PPLLEEAASSEENNOOTTEE::
If the battery fitting time has exceeded 5 minutes some time and temperature adjustment may be
necessary, please refer to the relevant sections located on page 2 and 3 of this user guide.
IIssoollaatteeaannyyeexxtteerrnnaalleelleeccttrriicciittyyssuuppppllyyttooyyoouurrCCeennttaauurrSSttaattbbeeffoorreerreeppllaacciinnggtthheebbaatttteerryy
between the battery terminals.
(see diagram).
Once batteries have been fitted, offer the left
hand side of the unit up to the mounting
plate ensuring that the two guide lugs are
fitted into the corresponding slots in the side
of the mounting plate.
Now swing the right hand side of the
CentaurStat up against the mounting plate
until the release button clicks into place.
After a few seconds the display will
Press the RELEASE BUTTON on the right hand side of the
unit and swing the front cover away from the mounting
plate by gently pulling on the right.
Remove the old batteries (with the batteries removed
your CentaurStat will retain its programme for
approximately five minutes) and replace them with
three new AA size alkaline batteries, ensure they are
fitted correctly as shown on the label positioned
8
Located under flap
12
11

SSEETTTTIINNGGTTHHEEDDAAYYAANNDDTTIIMMEEOOFFDDAAYY
Press the SET
button until SET
indicator is next to
the clock position
on the display.
Use PLUS
and MINUS
buttons to
adjust time
Press the SET button
until the SET indicator is
returned to the RUN
position.
Use PLUS
and MINUS
buttons to
adjust day
Press
ENTER
Use the PLUS button
to select a day to copy
the programme to
Press
ENTER
CCHHAANNGGIINNGGTTHHEETTIIMMEESSAANNDDTTAARRGGEETTTTEEMMPPEERRAATTUURREESS
The day setting
indicator will now flash.
Use the PLUS and
MINUS buttons to alter
the start day
DDEEFFAAUULLTTTTIIMMEESSEETTTTIINNGGSS
NOTE: When setting the time or altering the temperature settings, if a period exceeding 65 seconds is
allowed to elapse between button presses then the CentaurStat will automatically return to the run
position. Any alterations made since the last press of the ENTER button will not be recognised.
Press
ENTER
TTIIMMEEAANNDDTTEEMMPPEERRAATTUURREESSEETTTTIINNGGSS
The CentaurStat 7 has six temperature
settings per 24 hours. These all have
different start times and temperature
settings. The default factory settings are
shown opposite. Should you want to alter
these default times and temperatures,
proceed as instructed by the following
sections on page 3.
Repeat for all days that
require this programme - The day
indicator will remain illuminated
for days which have already been
copied to
Press
ENTER
Press the SET
button until the
SET indicator is
next to the PROG
position
Press
ENTER
The copy indicator will now illuminate,
this will allow the completed programme
to be duplicated into any or all of the
remaining days - If the copy feature is not
required press ENTER and continue with
the remaining days
Repeat for remaining
5 time and temperature
periods
Press
ENTER
Press
ENTER
The target temperature
setting for the 1st period will
now flash
Use the PLUS and MINUS buttons
to alter the target temperature
TTAARRGGEETTTTEEMMPPEERRAATTUURREEOOVVEERRRRIIDDEE
TTAARRGGEETTTTEEMMPPEERRAATTUURREELLOOCCKK
PAGE 2
Ensure the SET
indicator is in the normal
RUN position
Use the PLUS and MINUS buttons to
increase or decrease the
temperature settings
The CentaurStat will operate
on this new setting until the
next time period
The temperature lock facility allows you to ‘lock in’ the target
or override temperature of the current heating period.
With the SET indicator in the RUN position press the ENTER
button. The temperature lock symbol will appear on the right
hand side of the display. All controls buttons other then the
ENTER button will be inoperative.
The locked temperature will now override all other temperature settings until the lock is cancelled.
To cancel the temperature lock, and return to normal settings, simply press the ENTER button.
If an override temperature had been set before the lock was activated, the altered setting will remain
until the next switching period is reached.
PAGE 3
PPEERRIIOODDTTIIMMEESSTTEEMMPPSS..
1 6:00am 20oC
2 8:30am 18oC
3 11:30am 20oC
4 1:30pm 18oC
5 5:00pm 21oC
6 10:00pm 15oC
Electronic equipment can in some circumstances be affected by electrical interference. If the
programmer’s display becomes frozen or scrambled; or if you wish to revert back to the default time
settings please use the following procedure.
RREESSEETTTTIINNGGTTHHEECCEENNTTAAUURRSSTTAATT
PPEERRIIOODDTTIIMMEESSTTEEMMPPSS..
1 7:00am 20oC
2 10:00am 19oC
3 11:30am 21oC
4 1:30pm 18oC
5 5:00pm 21oC
6 11:00pm 15oC
The time setting for the
1st period the will now flash.
Use the PLUS and MINUS
buttons to alter the
start time
Programme the
remaining days, if
alteration to the preset
times are required
Press the SET
button until the
SET indicator is
returned to the
RUN position
DDIISSPPLLAAYYFFEEAATTUURREESS
The CentaurStat has 2 user
displays, by pressing the
PLUS and MINUS buttons
simultaneously, the user
can toggle between either
Display 1 or Display 2. DDiissppllaayy11- Shows current
time and target temperature
DDiissppllaayy22- Shows current
and target temperature
MONDAY - FRIDAY SATURDAY / SUNDAY
Press the SET and ENTER buttons together,
release the buttons and the CentaurStat will
return to preset factory default time settings.
Where an override temperature has been set, this altered setting, will remain until the next time and
temperature setting is reached.