Hot Wheels SLOT CAR RACING K4578-0921 User manual

I
f you have questions or difficulty operating your Race Set
–
the cause is often a simple problem. And there’s often a simple fix. Usually a quick “pit stop” will get you
racing again. Please check below, and then turn to the Maintenance section of the Instruction Manual for
detailed information.
If your vehicle stops…
• You may need to clean the track.
Please see Maintenance section: Track Cleaning.
• You may need to clean the vehicle.
Please see Maintenance section: Vehicle Cleaning.
• Check power connections.
Please see Power Connection section.
• Check your vehicle’s alignment.
Please see Maintenance section: Alignment.
• Check your vehicle’s contacts.
Please see Maintenance section: Contacts.
• Check to make sure track sections are properly connected.
Please see Basic Track Assembly section.
• Check your vehicle’s heat shield.
Please see Maintenance section: Heat Shield.
If your vehicle runs slowly or hesitates…
• You may need to clean the track.
Please see Maintenance section: Track Cleaning.
• You may need to clean the vehicle.
Please see Maintenance section: Vehicle Cleaning.
• Check your vehicle’s alignment.
Please see Maintenance section: Alignment.
• Check your vehicle’s contacts.
Please see Maintenance section: Contacts.
• Check to make sure track sections are properly connected.
Please see Basic Track Assembly section.
• Check your vehicle’s batteries.Check battery connector and replace with fresh alkaline battery.
If your vehicle spins out or flies off the track…
• You may need to clean the vehicle.
Please see Maintenance section: Vehicle Cleaning.
• Check your vehicle’s alignment.
Please see Maintenance section: Alignment.
• Check to make sure track sections are properly connected.
Please see Basic Track Assembly section.
• Check your vehicle’s heat shield.
Please see Maintenance section: Heat Shield.
• Check your vehicle for a missing guide pin.
Please see Maintenance section: Chassis Parts.
If your vehicle runs in on one lane, but not the other…
• You may need to clean the track.
Please see Maintenance section: Track Cleaning.
• You may need to clean the vehicle.
Please see Maintenance section: Vehicle Cleaning.
• Check power connections.
Please see Power Connection section.
• Check your vehicle’s alignment.
Please see Maintenance section: Alignment.
• Check your vehicle’s contacts.
Please see Maintenance section: Contacts.
• Check to make sure track sections are properly connected.
Please see Basic Track Assembly section.
• Check your vehicle’s heat shield.
Please see Maintenance section: Heat Shield.
If your vehicle runs backwards…
• Your vehicle’s rear axle assembly may be installed backwards.
Please see Maintenance section:
Chassis Parts.
Remove the rear axle assembly, reverse it and reinstall.
IF YOU STILL HAVE PROBLEMS –
OR IF IF ANY PARTS ARE MISSING OR DAMAGED –
DON’T
RETURN YOUR RACE SET TO THE STORE!
CALL OUR RACING
SUPPORT TEAM TOLL-FREE AT 1-888-557-8926 FOR HELP.
TROUBLESHOOTING GUIDE

II. DETAILED TRACK ASSEMBLY
a.
Your race set makes two different layouts. Refer to the Assembly Map for
detailed track assembly. Start with the Terminal Track
A
and continue
adding track pieces until your layout is complete.
b.
Once your layout is assembled, you’ll need
to add guardrails. Refer to the Assembly Map
for placement. To attach a guardrail: gently
flex the guardrail before attaching it. Carefully
attach the bottom of the guardrail first. Then
pull up and snap into place. Don’t force guard-
rails into place.
1.
There are letters molded into each
track piece. These letters are used in
these instructions to indicate which
track piece goes where. Following the
layout drawings on the Assembly Map,
you may want to lay out your track
– without connecting any track pieces.
That way you’ll be able to see how the
track layout goes together.
2.
To connect track pieces: working on
the flat surface, push the ends of the
track pieces together. Make sure they
snap together securely – you’ll hear a
click when they’re properly connected.
Remember: if the track connections
aren’t right, electric power won’t flow
from one track section to the next.
3.
To disconnect track pieces,
simply reach underneath where the
track pieces meet and press the
locking tabs together with thumb and
forefinger as shown.
Follow the step-by-step instructions to set up your race set.
Please separate the “Assembly Map” page, and keep it handy during assem-
bly. This page contains the contents list and large-scale Layout Drawings of
the fully-assembled track. You’ll need to refer to it as you go.
The Assembly Map looks like this:
INSTRUCTION MANUAL
Be sure to check out the Troubleshooting Guide on the back of the
Assembly Map.
I. BASIC TRACK ASSEMBLY
Start out on a clean, hard, flat racing surface – not carpeting. Take out all the
track pieces (and other parts) and check them carefully against the contents
list on the Assembly Map.
Sometimes brand-new track may need a quick cleaning for best
performance. Check the Maintenance section of this manual for more
information.
Occasionally the metal track rails will stick up too far from the surface
Occasionally the metal track rails will stick up too far from the surface
of a track piece, as shown. This may interfere with vehicle movement. To
of a track piece, as shown. This may interfere with vehicle movement. To
correct, simply press the rail back down with your finger. If the problem
correct, simply press the rail back down with your finger. If the problem
persists, please contact Customer Service toll-free at 1-888-557-8926
persists, please contact Customer Service toll-free at 1-888-557-8926
(see hours of operation in the Warranty section).
Keep these instructions
for future reference, as they contain important information.
Look for this symbol
throughout this manual. It indicates important infor-
mation.
START HERE! START HERE!
ADULT ASSEMBLY REQUIRED.
5
+
K4578-0920
®
MAIN LAYOUT DRAWING
Refer to the package for color photographs of the assembled layouts.
This page shows the contents list and large-scale Layout
Drawings of the fully-assembled track (tracks are not drawn to scale).
You'll need to refer to it as you assemble your race set.
Refer to the Instruction Sheet for detailed step-by-step instructions
for setting up and using your race set.
8
GUARDRAILS
6
F
9" RADIUS CURVE
1
C
6" STRAIGHT
1
A
9" TERMINAL TRACK
1
SANDPAPER
1S
15" SQUEEZE
2
CONTROLLERS
1
2
3
13
= GUARDRAILS
= TRACK SUPPORTS
1 = Beginner
2 = Average player
3 = Skilled player
1
2
3
2
#2 SUPPORTS
1
6
CLIPS
Use either a diorama or a guardrail on the outside of the curves.
1
BATTERY PACK
F
F
F
F
S
C
A
1
1
F
F
C
S
F
F
F
F
A
1
2
3
1
2
3
ALTERNATE LAYOUT DRAWING
K4578-0921
© 2006 Mattel, Inc., PRINTED IN CHINA. All Rights Reserved.
1
VEHICLE
1
VEHICLE
CHOKING HAZARD
–
Small parts.
Not for children under 3 years.
WARNING:
!

c.
Next you’ll need to add the track supports. Refer to the Assembly Map for
placement. Attach them as shown. To assemble a track support, separate
the pieces as shown and snap off the connector tabs (discard the tabs).
Next, fit the two pieces together as shown. Insert the assembled track sup-
port into the round hole on the underside of the track as shown.
CONGRATULATIONS!
CONGRATULATIONS!
CONGRATULATIONS!
CONGRATULATIONS!
CONGRATULATIONS!
You’re ready to race. For “pro” competition, please read the following driving
You’re ready to race. For “pro” competition, please read the following driving
tips and maintenance hints.
DRIVING TIPS
Here are some “inside” racing tips…for top performance!
1.
Always race on a clean, hard, flat surface. For best
racing performance, we don’t recommend carpeting.
2.
Clean track is IMPORTANT for best performance! Please refer to the
Maintenance section for detailed instructions for cleaning the track.
3.
Races are won in the curves! Slow down going into
the curves…then speed up coming out of them.
Accelerate to build up speed for loops and jumps.
4
. Anyone can be a “pro” racer – the secret is practice! Remember to “break
in” your new cars with a few “qualifying” laps. Cars always run better after
they’ve “warmed up.”
5.
Experienced racers know that regular maintenance is the key to top racing
performance. Read and follow
the easy steps in Section II.
6.
If you have questions or difficulty operating your Race Set, check the
Troubleshooting Chart first. Usually a quick “pit stop” will get you racing
again!
MAINTENANCE:
ADULTS NOTE: All “pro” racers know that their vehicles need mainte-
nance from time to time…for best performance. Follow these simple
steps to keep your car running at its best!
A. CHASSIS PARTS
This diagram will help you understand the parts of your vehicle, and how they
go together.
❶
Guide Pin
❷
Front Tires
❸
Rear Tires
❹
Rear Axle Assembly
❺
Contacts
❻
Front Axle Assembly
❼
Springs
➑
Heat Shield
USE ALKALINE BATTERIES ONLY.
Battery Performance Note: For best performance use alkaline batteries
(where disposable batteries are called for). Replace batteries when vehicle
motion becomes too slow.If your product is supplied with standard (carbon-
zinc) batteries for initial use and/or demonstration purposes, we recommend
replacing them with alkaline batteries when necessary. Battery life may vary
depending on battery brand.
Always unplug your Battery Pack when not in use!
a.
The cables for the Battery Pack and
the hand controllers have color-coded
plugs to help you make your connections
properly. First, plug the red plug into the red
receptacle on the terminal track. Next, plug
the yellow hand controllers into the yellow
receptacles on the terminal track.
b.
To test track and power connections, hold
a car on the track with its metal contacts
touching the metal track rails. Gently
hold the front end of the car down while
lifting the vehicle as shown (do not lift the
vehicle by its rear tires). Squeeze the hand
controller: the car’s rear tires should spin.
If they don’t, there’s a connection problem.
Carefully check the track and power
connections.
c.
Your hand controller is your car’s “throttle.”
The more you squeeze the trigger the faster
your car will go. Practice at a slow speed
for a few laps, until you’re ready to race!
SPECIAL NOTE TO ADULTS:
• Always make sure your Race Set is unplugged before assembling or
disassembling track. Always unplug Battery Pack when not in use.
Regularly examine for damage to the cord, plug, enclosure and other
parts.
• In the event of any damage, this toy must not be used with the battery
box until the damage has been repaired.
• If this toy is being operated in the presence of children under 5 years
old, adult supervision is recommended.
• This toy is not intended for children under 3 years old.
• Disconnect from the battery box before cleaning.
III. BATTERY BOX / HAND CONTROLLER ASSEMBLY
Requires 4 x 1.5V "D" size (LR20) batteries (not included). Install 4 x 1.5V "D" size
(LR20) alkaline batteries (not included) as shown.
A
1
2
3
1
2
3
A
1
2
3
1
2
3
34
1
2
7 2
3
5
6
7
8

E. CONTACTS
1. CLEANING CONTACTS
Regularly clean your car’s
contacts to remove oxidation. Using a
pencil eraser, as shown, carefully scrub the
contacts. Do not apply too much
pressure, or you may bend contacts.
DO NOT USE STEEL WOOL.
Worn-out contacts can be replaced.
2. CONTACT REPLACEMENT
Your vehicle’s contacts should last a
minimum of 8-10 total hours of racing, with
regular cleaning. You may need to replace
the contacts if they become overly worn or
bent…or if they become dislodged after an
impact.
The best way to replace contacts is one
at a time, using the remaining contact
assembly as a guide. Be careful not to
bend the contacts out of shape
(especially wide slotted end).
a.
Hold chassis bottom side up. Hold the
spring as shown (with your thumb on one
side of the chassis and your forefinger on
the other). You’ll need to hold the spring
securely throughout the assembly process.
b.
Hook the narrow end of the contact under
the motor shaft. Hook the curved side tab
of the contact over the spring; the spring
will be held in place by the curved tab.
Place the wide (slotted) end of the contact
into place, with the chassis tab through
the slot. Making sure not to over bend the
contact slot.
c.
Still holding the spring securely, turn the
chassis over. You may need to press the
top of the contact into place with the tip of
a pencil. When properly installed, the con-
tact will spring back when pushed.
F. HEAT SHIELD
1. INSTALLATION
The heat shield is an important compo-
nent, and it must be correctly installed for
proper vehicle operation. Make sure the
side tabs of the heat shield are properly
inserted in the chassis slots, as shown. If
the heat shield is not correctly installed, it
may interfere with vehicle movement.
2. CLEANING
Occasionally dust and debris may build
up under the vehicle’s heat shield, inter-
fering with operation. To check for this
problem, stop racing and let the vehicle
sit for 5 minutes. Remove the heat shield
and gently blow out any dust. Reinstall
the heat shield as described above.
Don’t operate any vehicle without a heat
shield. If the heat shield is lost, or can’t
be installed properly, please contact
Customer Service at the toll-free
number shown in this manual.
CHASSISCHASSIS
(back view)(back view)
(back view)
(back view)
(back view)
(back view)
B. TRACK CLEANING
Clean track is IMPORTANT for best perfor-
mance!
1.
Dirty track may cause your vehicle to
stall. Usually you can get it going again
by pressing the hand controller trigger
about halfway down while you give the
vehicle a slight push from behind. After
3-4 laps your vehicle will run properly.
2.
Sometimes oxidation may form on the
track rails, and this may cause your car
to stall. If this happens, you’ll have to
remove the oxidation. Using the supplied
sandpaper, GENTLY rub the track rails.
Don’t rub hard – rails are clean when
they’re shiny. After cleaning, wipe the
track with a soft, clean, lint-free cloth to
remove any residue (don’t use tissue or
paper towels).
NEVER use steel wool to clean your
track: severe damage can result if a
fiber of steel wool is picked up by the
magnets in your car’s motor. Use only
very fine sandpaper for cleaning.
3.
Sometimes debris can accumulate in the
track slots. If this happens, use a tooth-
pick to clear the debris from the slots.
C. VEHICLE CLEANING
1. CLEANING TIRES
Dirty tires can cause your car to lose
traction and spin. To clean the tires,
place a piece of adhesive tape on a hard,
flat surface, with the sticky side facing
up. Roll the rear tires across the tape
until they’re clean.
2. CLEANING AXLE
Lint may collect around your car’s axles:
this may cause the car to run slowly. Use
tweezers or a toothpick to remove lint as
shown.
D. ALIGNMENT
1. AXLE ALIGNMENT
Your car’s axle assembly may become
“dislocated” from the chassis as a result
of a sudden impact. To realign it, snap
the assembly back into the chassis.
DO NOT use any type of tool to snap the
chassis back in place. Use only your
fingers.
2. CHASSIS ALIGNMENT
Occasionally check the position of the
car’s body to make sure it is properly
aligned and not rubbing against the tires.
If necessary, carefully snap chassis back
onto the body tabs, as shown.

Mattel, Inc., 333 Continental Blvd., El Segundo, CA 90245 U.S.A. Consumer
Relations: 1-800-524-8697. service.mattel.com
Mattel U.K. Ltd., Vanwall Business
Mattel U.K. Ltd., Vanwall Business
Park, Maidenhead SL6 4UB. Helpline 01628500303
Park, Maidenhead SL6 4UB. Helpline 01628500303
Mattel Australia Pty Ltd.,
Richmond, Victoria. 3121. Consumer Advisory Service - 1300 135 312. Mattel
East Asia Ltd., Room 1106, South Tower, World Finance Centre, Harbour City,
Tsimshatsui, HK, China. Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.(993532-
P) Lot 13.5, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ.
Tel:[phone], Fax:[phone]
.
Battery Safety Information
In exceptional circumstances batteries may leak fluids that can cause
a chemical burn injury or ruin your product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before
being charged (if designed to be removable).
• Rechargeable batteries are only to be charged under adult supervi-
sion (if designed to be removable).
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-
cadmium) batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to
be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may
explode or leak.
90-DAY LIMITED WARRANTY
HOT WHEELS
®
SLOT CAR RACING
Mattel, Inc. warrants to the original consumer purchaser that this
product will be free of defects in material and workmanship for nine-
ty (90) days (unless specified in alternate warranties) from the date
of purchase. Mattel will replace the product in the event of such a
defect within the warranty period.
In the event of a defect covered under this warranty, first call the
toll-free number listed below. Many problems can be solved in this
manner. If necessary, you will be instructed to return the product,
postage prepaid and insured, to the address below. Enclose your
name, address, dated
sales receipt, and a brief explanation of the
defect. Replacement and return shipment will be free of charge.
This warranty does not cover damage resulting from unau-
thorized modification, accident, misuse or abuse. If the product is
returned without a dated sales receipt the product may be excluded
from coverage under this warranty.
Mattel’s liability for defects in material and workmanship under this
warranty shall be
limited to replacement, and in no event shall we
be responsible for incidental, consequential, or contingent
damages
(except in those states that do not allow this exclusion or limitation).
This warranty is exclusive,
and is made in lieu of any express or
implied warranty.
Valid only in U.S.A.
This warranty gives you spe-
cific
legal rights and you may have other rights, which vary from
state to state. Some states do not allow the exclusion of incidental
or consequential damages, so the above exclusions or limitations
may not apply to you.
TOLL-FREE NUMBER: 1-888-557-8926
(valid only in U.S.A.)
Hours: 8:00 A.M. - 5:00 P.M. Eastern Time; Monday - Friday. Expect
some delay in January following the holiday season. Please be
patient and keep trying the toll-free number.
ADDRESS FOR RETURNS: CONSUMER RELATIONS
636 GIRARD AVENUE
EAST AURORA, NY 14052
Protect the environment by not disposing of this product with
household waste [2002/96/EC]. Check your local authority for
recycling advice and facilities.

MAIN LAYOUT DRAWING
Refer to the package for color photographs of the assembled layouts.
This page shows the contents list and large-scale Layout
Drawings of the fully-assembled track (tracks are not drawn to scale).
You'll need to refer to it as you assemble your race set.
Refer to the Instruction Sheet for detailed step-by-step instructions
for setting up and using your race set.
8
GUARDRAILS
6F
9" RADIUS CURVE
1
C
6" STRAIGHT
1
A
9" TERMINAL TRACK
1
SANDPAPER
1S
15" SQUEEZE
2
CONTROLLERS
1
2
3
13
= GUARDRAILS
= TRACK SUPPORTS
1 = Beginner
2 = Average player
3 = Skilled player
1
2
3
2
#2 SUPPORTS
1
6
CLIPS
Use either a diorama or a guardrail on the outside of the curves.
1
BATTERY PACK
F
F
F
F
S
C
A
1
1
F
F
C
S
F
F
F
F
A
1
2
3
1
2
3
ALTERNATE LAYOUT DRAWING
K4578-0921
© 2006 Mattel, Inc., PRINTED IN CHINA. All Rights Reserved.
1
VEHICLE
1
VEHICLE