Hotron SSS-5 User manual

2. WIRING TO THE DOOR CONTROLLER
3. DIPSWITCH SETTINGS
1
1. MOUNTING THE SSS-5 ON THE DOOR
SSS-5: Quick Installation Guide
2
2
NO
3
1/ Test Input 2/ Optical Interference
2/ Use a weather cover if the
unit is installed where rain will
fall directly on it.
PCB Unit
4/ Remove the Angle Stabilizer and loosen the screw on
one of the PCB Holders to slide it aside and remove the
PCB Unit.
Angle Stabilizer
PCB
Holder
5/ Attach the Aluminium Case to the door with the screws provided.The Aluminum Case(s)
should be located close to the Leading edge of the door to maximise safety detection.
Aluminum
Case
torque
0.5 Nm
LEADING
EDGE
MARK
Leading Edge
of Door
6/ Reinsert the PCB unit, making sure that the side marked “LEADING
EDGE”is closest to the leading edge of the door. Re-attach the Angle
Stabilizer and tighten the screws on the PCB Holders.
1/ Drill Holes as indicated and install the
Jamb Hole Cover A on the door
controller
Unit : [mm]
30
10 15
Screw Holes Wiring Hole
3 - φ2.6 φ10
1
7
A
50mm
Check that the detection range
conforms to EN16005
EN16005
B
A
A
Without TEST
With TEST
0v
B
Without TEST
0v
AB
SSS-5 SSS-5
3/ Relay Output Mode
3
NC
4/ Masking Detection Spots
4 5
1
2
3
4
5
6
4 5
1
2
3
4
5
6
4 5
1
2
3
4
5
6
4 5
1
2
3
4
5
6
5/ Setting Non-Detection Distance
6 7 8
100mm
6 7 8
150mm
6 7 8
200mm
6 7 8 6 7 8
300mm
6 7 8
400mm
6 7 8
500mm
6 7 8
250mm
Terminal
Block
To avoid cross interference between two
sensors in close proximity different
frequency settings should be selected
Door Leaf
Detection
A
Set Non-Detection
distance
Power supply ( AC/DC 12～24[V] )
Relay Output ( Common )
Relay Output 1
Relay Output 2 (Second PCB Unit Output)
2
3
4
1
5
TEST Input ( - )
6
TEST Input ( + )
7
Hinge
Extra Wire Hole through the door
Jamb Hole Cover Wire Sheath
Door
Controller
Connector 6P
PCB Unit1
7P Terminal
PCB Unit2
7P Terminal
（Unused）
PCB units are connected to each
other using the Communication
Cable (supplied)
Slide SW
「OFF｣
Hole(φ10) drilled
through the door.
Hinge
Jamb Hole Cover
「ON｣
PCB Unit1
7P Terminal
「OFF｣
PCB Unit2
7P Terminal
「OFF｣
Door
Controller
Note: Remember to set the Slide SW as indicated
4/ Option 1: Plan view, wiring PCB units on both side of the door independently
back to the door controller
4/ Option 2: PCB units on both sides of the door connected via communication
cable and only 1 PCB unit wired back to door controller
2/ Clamp the Wire Sheath between the Jamb
Hole Cover A/B
Jamb Hole
Cover A
Jamb Hole
Cover B
Wires to
the controller
Wire Sheath
1/ Do not mount the sensor
higher than 2.6 [m]( 8' 6" ).
2.6 [m]
Hinge
<Top view>
Leading edge
Hinge
Leading edge
3/ Unscrew the Side Covers and remove
the Filter Cover.
Side Cover
Filter Cover
Aluminium Case
3/ Remove the Terminal Block from the PCB unit and connect the wires
from the door controller to it as indicated. See wiring options below.
Communication
Cable
PCB unit
= Default Setting
When connected to a door controller
with a TEST input, set to “B”.
When connected to a door controller
without a TEST input, set to “A”.
Set to “B”to comply with EN16005
EN16005
Default
Settings 21 3 4 5 6 7 8
Tighten screw
PCB Holders
Note: Remember to set the Slide SW as indicated
Leading
Edge
Leading
Edge

6. TEACHING
7. REPLACE FILTER COVER
TEACHING”is necessary so that the sensor can learn the distance from
the sensor to the floor.
1/ Clear the detection area
2/ Press the “Push SW” switch for 2s or more
3/ GREEN & RED LED flashes slowly for 10s, followed by
faster frequency flashes indicating that TEACHING is been
executed (If during this time, a person or object is in the
detection area, try again from STEP 1.)
4/ Green LED flashes once to indicate that the TEACHING
process is complete
5/ Verify the detection area for conformity to local regulations
Install the Filter Cover
1/ First fit the upper side of the Filter Cover into the full
length of the Aluminum Case.
2/ Slightly bend the Filter Cover at one end to latch it onto
the bottom lip of the Aluminum Case.
3/ Slide your hand along the bottom lip to lock the Filter
Cover in place
Attach the Joint
12 3
Snap the Joint into
Aluminum Case.
Slide the Joint so that it fits
snugly into the Filter Cover.
Attach remaining Filter Cover as
illustrated
Cut out the Side Cover wiring point and
insert the Wire Sheath into it.
Attach the Side Cover with
Screws provided.
Screw
After the Filter Cover is fitted, confirm that the detection range is as expected
and conforms with local regulations.
Check that the detection area conforms to EN16005
EN16005
8. FINAL DETCTION RANGE CHECK
5゜
1.
(1)Lift
(2)Slide
2.
(3)Rotate PCB unit
3.
(4)Slide Back
25゜
4. DETECTION ANGLE ADJUSTMENT
5゜25゜
20゜
15゜
10゜
Side View
5. LED
Standby: GREEN LED ON
Detecting: RED LED ON
Environmental Error: Fast alternate RED/GREEN LED followed by 1
flash of RED LED. If this happens execute the TEACH
function again with a white sheet of paper on the ground.
Internal Sensor Failure: Fast alternate RED/GREEN LED followed by 3
flashes of the RED LED
The detection angle can be adjusted between 5 - 25 [deg] in 5 [deg] increments using
the Angle Stabilizer.
SSS-5: Quick Installation Guide
For a more detailed explanation on how to install the SSS-5 sensor please see the full installation instructions on our website at;
https://hotron.com/wp-content/uploads/2020/09/mp-10193_04_d201911271.pdf