HP f920 Series User manual

f920x Kit
Car Camcorder
User Manual

1
Contents
About this Guide.......................................................................................... 3
Re ulatory notices ...................................................................................... 3
Prohibition of co-location ........................................................................... 3
WEEE Notice ................................................................................................ 3
CE Re ulatory Notice .................................................................................. 3
Notes on Installation ................................................................................... 4
Caution ........................................................................................................ 4
1 Introduction ................................................................................ 7
1.1 Features .......................................................................................... 7
1.2 Packa e Contents ........................................................................... 7
1.3 Product Overview ............................................................................ 8
2 Getting Start ............................................................................. 10
2.1 Stora e Media ............................................................................... 10
2.1.1 Insert the Memory Card ..................................................... 10
2.1.2 Remove the Memory Card ................................................. 10
2.2 Install Front Cam ........................................................................... 11
2.3 Exchan e Front Cam’s Mount ........................................................ 12
2.4 Install Rear Cam ............................................................................ 13
2.5 Connect Front and Rear Cam ......................................................... 14
2.6 Connectin to Power ..................................................................... 15
2.7 LED Indicator ................................................................................. 15
2.8 Powerin the Camcorder On / Off ................................................. 16
2.8.1 Auto Power On/Off ..................................................................... 16
2.8.2 Manual Power On/Off ................................................................ 16
2.8.3 Reset…… .................................................................................... 16
2.9 Initial Settin s ............................................................................... 16
2.9.1 Set Time zone ............................................................................ 17
2.9.2 Set the Date / Time .................................................................... 17
3 Using the Car Camcorder ............................................................ 18
3.1 Automatic Record .......................................................................... 18
3.1.1 The Recordin Screen ........................................................ 19

2
3.2 Emer ency Recordin ................................................................... 21
3.3 Picture in Video ........................................................................... 21
3.4 Drivin Safety ............................................................................. 22
3.4.1 Speed Cam Alert ................................................................ 22
3.4.2 Add Speed Point ................................................................ 23
3.4.3 Speed Limit Alert ............................................................... 23
3.4.4 Driver Fati ue Alert ........................................................... 24
3.4.5 LDWS ................................................................................. 24
3.4.6 FCWS ................................................................................. 26
3.5 Parkin Mode ................................................................................ 27
3.5.1 Park Recordin .................................................................. 27
3.5.2 Motion and Collision Detection .......................................... 28
3.5.3 Timelapse .......................................................................... 28
3.6 Collision Detection ........................................................................ 29
3.7 File Playback ................................................................................. 29
3.8 Playback Screen ............................................................................ 30
3.9 Deletin Files ................................................................................ 31
4 Initial set up Go Dashcam application ......................................... 32
4.1 Download and install .................................................................... 32
4.2 Wi-Fi connectin ........................................................................... 33
Using the Go Dashcam application .............................................. 34
5.1 Camera preview, record, snapshot ................................................ 35
5.2 Playback, delete, download .......................................................... 36
5.3 Local album ................................................................................... 38
5.4 Camera Settin ............................................................................. 39
6 Adjusting the Settings ............................................................... 40
6.1 Usin the Menu ............................................................................. 40
7 SuperCar 2.0 ............................................................................. 44
8 Specifications ........................................................................... 4

3
About this Guide
The content in this document is for information purpose and is subject to
chan e without prior notice. We have made every effort to ensure that this
User Guide is accurate and complete.
However, no liability is assumed for any errors or omissions that may have
occurred.
The manufacturer reserves the ri ht to chan e the technical specifications
without prior notice.
Regulatory notices
This document provides country- and re ion-specific non-wireless and
wireless re ulatory notices and compliance information for your product.
Some of these notices may not apply to your product.
Prohibition of co-location
This device and its antenna(s) must not be co-located or operated in conjunction with any
other antenna or transmitter.
WEEE Notice
Disposal of Waste Electrical and Electronic Equipment and/or Battery by
users in private households in the European Union
This symbol on the product or on the packa in indicates that
this cannot be disposed of as a household waste. You must
dispose of your waste equipment and/or battery by handlin it
over to the applicable take-back scheme for the recyclin of
electrical and electronic equipment and/or battery. For more
information about recyclin of this equipment and/or battery,
please contact your city office, the shop where you purchased the
equipment or your household waste disposal service. The
recyclin of materials will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health
and environment.
CE Regulatory Notice
The product herewith complies with the requirements of the Low Volta e
Directive 2014/35/EU, the EMC Directive 2014/30/EU, the RED-Directive
2014/53/EU and the RoHS Directive 2011/65/EU.

4
EU Health Protection: This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Notes on Installation
1. Please measure the front windshield viewin area, make sure not to block
driver's front view, install the camcorder below the rearview mirror (the
central, hi her ri ht position of the front windshield). And we recommend
that the sky and the land occupied by the screen 50%, fix the car holder
and then adjust the camcorder so that the lane is ali ned with the screen.
Proper installation enables the camcorder to maximize the efficiency also
can enhance the accuracy of LDWS.
2. Make sure that the lens is within the wipin ran e of the windscreen wiper
to ensure a clear view even when it rains.
3. Do not touch the lens with your fin ers. Fin er rease may be left on the
lens and will result in unclear videos or pictures. Clean the lens on a
re ular basis.
4. Do not install the camcorder on a tinted window. Doin so may dama e
the tint film.
5. Make sure that the installation position is not hindered by the tinted
window.
6. This product is suitable for li ht windshield or li ht color heat-resistant
film windows , it will affect video quality if install it on the dark windows
or dark heat-resistant film windows.
7. Use the products of the attached power char er only, please do not use
other brand power char er, in order to avoid equipment burn.
Caution
Due to local laws and vehicles safety considerations, do not operate the
camcorder while drivin .
Set up time zone, time and date accurately before you use this
camcorder.
Please use SuperCar software under the condition that Electronic Map
are functionin normally.
The firmware function in the camcorder is for reference only, drivers are
advised to exercise discretion based on actual road conditions.
The results of GPS positionin are only for reference, and should not
affect the actual drivin situation. The camcorder also cannot ensure the
positionin accuracy.
GPS positionin accuracy may differ dependin on weather and location
such as hi h buildin s, tunnels, under rounds, or forests. GPS satellite

5
si nals cannot pass throu h solid materials (except lass). Tinted
window will also affect the performance of the GPS satellite reception.
GPS reception performance on each camcorder may differ. The
camcorder cannot determine the accuracy of the positionin results
from different hardware.
The values displayed in this camcorder, such as speed and position,
may be inaccurate due to the influence of surroundin environment.
They are for your reference only.
This product is used only for non-commercial use, within the maximum
limits permitted by applicable law. We do not take any responsibilities
for the loss of use of the product.
Wi-Fi Si nals are unable to pass throu h the buildin . The upper limit of
si nal transmission is 5m.
Wi-Fi Operation Channel: Ch1~Ch11
The product employs wireless data communication which may interfere,
or be interfered by, a near-by camcorder.
Never use this camcorder in the vicinity of a microwave oven or at places
where there is radio interference.
Radio wave reception may be worsened in specific environments.
Please be advised that if another camcorder is also usin the same
2.4GHz band as this product, the processin speed of both camcorders
may slow down.
This camcorder ets warm when in use; this is normal.
Improper use or operation of the product may result in dama e of the
product or its accessories and void the warranty.
The radio frequency (RF) enerated by this RF electronic camcorder may
cause adverse effects on the operation of other electronic camcorders
and result in malfunctionin . Wireless transmitters and circuitry may
also interfere with other electronic camcorders. Therefore, do observe
the followin precautions:
•Aircraft: Never use a radio transmitter when you are in an airplane.
Please switch off the Wi-Fi function of the camcorder.
•Vehicle: The radio frequency transmitted by this camcorder may
affect the electronic system in a motorized vehicle. Please consult
the manufacturer or dealer of your vehicle on the possible effect.
•Pacemaker: In order to prevent any potential interference to a
pacemaker, anyone who uses a pacemaker should be advised, that,
when usin this camcorder, a minimum distance of 15cm (6 inch)
should be kept between the camcorder and the pacemaker; and

6
never put this camcorder in a chest pocket. In case of any doubt of
interference, switch off the camcorder immediately.
•Medical Camcorder: If you use a personal medical camcorder,
consult the camcorder manufacturer or your physician to confirm if
your camcorder is sufficiently shielded from the RF transmission of
this camcorder.
•Medical Facilities: Hospitals and medical institutes may use
facilities that are sensitive to an external RF ener y. Observe such
instructions when the medical care personnel or any posted si n
requests you to switch off any camcorder that may interfere the
radio frequency.
•Explosion sites or any location with a posted si n: In order to
prevent interferin with an explosion activity, observe all the
si na e and instructions in the Explosion Area or in a zone with a
“Switch Off 2-way Radios” si n by switchin off camcorders that
may interfere with the radio frequency.
HP Inc. is NOT responsible for the loss of any data/content durin
operation.
Before you start using the product, it is assumed that you agree to
the above statement.

7
1Introduction
Thank you for purchasin this advanced Car Camcorder. This product is
specifically desi ned for real time video recordin when drivin .
1.1 Features
Front Cam: f920x
•Full HD 1920*1080P
•1.3" TFT-LCD color screen
•Wide an le lens
•Collision Detection, when a collision is detected, the camcorder will
automatically tri er the emer ency recordin
•Parkin Mode
•Multifunction traffic safety reminder
Rear Cam: RC
•Full HD 1920x1080P
•Switch for rear view or in-car recordin
•Sony’s Starvis sensor
1.2 Package Contents
The packa e contains the followin items. In case there is any missin or
dama ed item, contact your dealer immediately.
Car Camcorder
f920x
Electrostatic Sticker Main Unit Mount
(T-buckle)
Bracket Car Adapter Rear Camera RC5
Micro USB cable
(rear cam connection) E-Manual

8
1.3 Product Overview
Front Cam: f920x
No. Item No. Item
1 LED Indicator 8 Microphone
2 LCD Panel 9 Wide An le Lens
3 Menu / Back Button
( / )
10 Power button
4 Add Speed Cam / Up Button (
/
)
11 Memory Card Slot
5 Snapshot / Down Button
( / )
12 Power Connector
6
Emer ency Recordin / Confirm
Button
( /
OK
)
13 Rear Camera Connector Port
7 Speaker 14 Main Unit Mount
(Adhesive Pad)

9
Rear Cam: RC
No.
Item
No.
Item
1 Wide An le Lens 4 Camera Rotation Shaft
2 Base 5 Rear/ Front Ima e Switch
3 Micro USB Connector Port 6 LED Indicator

10
2Getting Start
2.1 Storage Media
2.1.1 Insert the Memory Card
Insert memory card with the olden pins facin forward and the screen of the
camcorder facin down, see the picture as below:
2.1.2 Remove the Memory Card
If the camcorder is power on, please power off first and wait for the procedure
of switchin off the camcorder completed before removin the memory card.
Note:
1. Do not remove or insert the memory card when the camcorder is turned on. This may dama e the memory
card.
2. Support microSD class 10 and memory stora e 16GB or above (support up to 128GB).
3. Please use this car camcorder to format the microSD card before the initial use. The formatted file type for
this camcorder is FAT32.
4. Periodically format the microSD card (recommended period: once a month).

11
2.2 Install Front Cam
1. Put the electrostatic sticker onto the su ested area on the windshield.
Before puttin the sticker, please wipe and clean the windshield. Durin
the installation, please make sure the bubbles in between the sticker
and the window are all one.
1.
Peel off the protective plastic
sheet from the adhesive pad.
2.
Place and press the bracket firmly
onto the electrostatic sticker on the
windshield window. Make sure the base
is securely locked in place.
3.
Swivel the camcorder to adjust
view an le.
5. Make sure the camcorder is securely locked in place.

12
2.3 Exchange Front Cam’s Mount
1. Push down the Adhesive Pad and take it out.
2. Without Adhesive Pad, you can see 2 holes and 1 up-pointin arrow mark
on the case.
3. Make sure the up-pointin arrow mark on the T-buckle Mount is up.
4. Flip over the T-buckle Mount, and put 2 hooks of the T-buckle Mount
onto 2 holes of the case, and push it up until “click” sound is heard.
Note:
When usin the T-buckle mount, install it with a suction bracket. Buckle the device and the suction
bracket first, wipe the lass clean, install the suction bracket on the windshield, ently press and
confirm that the bracket is fixed. Loosen the knob on the bracket to adjust the viewin an le of the
device. After adjustment, ti hten the knob of bracket.

13
2.4 Install Rear Cam
1. Adjust rear camera position as the picture shown. Please check the
preview ima e is in ri ht position (not upside down) before installation.
If the preview ima e is upside down, please rotate the base 180∘to make
it correct, or make sure switch is REAR or FRONT position.
Rear view recordin In-car recordin
2. Connect the USB cable with front cam and rear cam, power on front cam
to preview screen and confirm the field of view. Then clean the surface
of the windshield with alcohol to ensure that the adhesion surface is
clean.
3. Remove the transparent film on the base of rear cam, and then hard
press rear cam to ensure firmly stuck.
Note: We recommend users to disconnect micro USB from rear camera before adjustin .

14
2. Connect Front and Rear Cam
Use only the USB cable in packa e to connect with front camera and rear
camera.
1. Plu phone jack into front camera’s 2CH port. (Front camera is power-off.)
2. Plu the other end of USB cable (micro USB connector) to rear camera’s USB
port.
3. Turn on front camera’s power, the rear camera ima e will be shown on the
ri ht down corner of front camera screen. Accordin to different models,
press Power button on front camera to switch front or rear ima e.
Note:
1. Install rear camera at upper central position of the rear windshield.
2. Rear camera doesn’t support hot Plu -n-Play. Please turn off the front camera before plu in the rear
camera.

15
2.6 Connecting to Power
Use only the attached power adapter to activate the camcorder.
1. Connect one end of power adapter to power connector port on the front
cam. USB port input: DC 5V / 2A.
2. Plu the other end of the power adapter to the ci arette li hter socket of
your vehicle. Once the vehicle en ine is started, the camcorder
automatically turns on. Power adapter input: DC 12 / 24V.
Note:
Use the products of the attached power adapter only, please do not use other brand power char er, in order
to avoid equipment dama ed.
2.7 LED Indicator
Status Explanation LED Indicator Color
Power off, connect external power Red
Power on, standby Green
Recordin / Recordin and screen off Flash red

16
2.8 Powering the Camcorder On / Off
2.8.1 Auto Power On/Off
If the camcorder is connected to the vehicle power supply, once start the car
en ine, the camcorder will automatically power on and start recordin .
Once the vehicle en ine shuts down, the camcorder automatically saves the
recordin and turns off the power.
2.8.2 Manual Power On/Off
To manually turn on the power, press the POWER button.
To turn off, press and hold the POWER button for at least 2 seconds.
2.8.3 Reset
Press and hold the Power button for 8 seconds to reset the device.
2.9 Initial Settings
Before usin the camcorder, we recommend you setup the correct Time zone,
Date and Time.
Note:
Please note that if you press the button durin recordin , the system will stop recordin and enter
OSD menu. Make sure the recordin is already stopped then continue operatin the menu.

17
2.9.1 Set Time zone
To set the time zone, do the followin :
1. Press the button to enter the OSD menu.
2. Press the / button to select Set Time zone, and then press the
OK
button for enterin function menu.
3. Press the / button to set the current time zone, and then press
the
OK
button to complete settin .
4. Press the button to return to recordin screen.
Note: If satellite positionin is not successful, camcorder clock will run based on user defined time.
2.9.2 Set the Date / Time
To set the correct date and time, do the followin :
1. Press the button to enter the OSD menu.
2. Press the / button to select Date / Time, and then press the
OK
button for enterin function menu.
3. Press the / button to adjust the value, and then press the
OK
button to set the next field.
4. Repeat step 3 until the date and time settin is completed.
Note:
To ensure the accuracy of the video file time, please reset the date and time when not in use over 7 days.

18
3Using the Car Camcorder
3.1 Automatic Record
Start the car en ine, wait a few seconds to char e the camcorder, and then
screen will li ht up and the camcorder will automatically power on and start
recordin .
Recordin will automatically stop when the en ine is switched off.
Note:
1. Some vehicle power supply would not turn on / off automatically with the car en ine start, if the
camcorder cannot automatically power on/off with the car en ine, please manually connect the power
supply with the vehicle power, and then power on, or manually power off the camcorder and then release
the connector with the car power supply.
2. It can be confi ured to save a video file for every 30 seconds, 1 or 3 minutes of recordin .
3. All the videos and photos are saved in the memory card, if memory card is full, loop recordin will be
enerally overwrite the oldest video file.
4. The camcorder is built-in super capacitor. After start the car en ine, please wait a few seconds for
char in the camcorder, and then the camcorder will automatically power on and start recordin .

19
3.1.1 The Recording Screen
No. Icon Item Description
1
00:10
Recordin
Duration Indicates the video current duration.
2 Date / Time Indicates the current recordin date
and time.
3 Menu Button Durin video recordin , press the
button to enter the Menu.
4
Add Speed Point
Button
Durin video recordin , press the
button to add a speed cam
point.
5
PIV (Picture in
Video) Button
Press to capture video screen
shots.
6
Emer ency
Recordin Button
Durin video recordin , press the
OK
button to enter emer ency
recordin mode.
7
Resolution
icon Indicates the video resolution.