HP 97060 CE User manual

HP 9000 Series 500 Computers
97060 CE Handbook
Part No. 97060-90039
E 0184
Requires Binder No. 9282-0683
Flin- HEWLETT
~a111 PACKARD
Printed in USA
First Edition. January 1984

97060 CE Handbook
c COPYright 1984, Hewlett-Packard Company
This documentcontains proprietary Information which
IS protected by copyright. All rights are reserved. No part of this
document may
be photocopied, reproduced or translated to another language without the prior written consent of
Hewlett-Packard Company. The Information contained
In this document IS subject to change without notice
Restricted Rights Legend
Use, duplication, or disclosure by the Government
IS sublect to restrictions as se1 forth in paragraph (b)(3)(B) of the
Rights
In Technical Data and Software clause in DAR 7-104 9(a)
Hewlett-Packard Company
3404 East Harmony Road, Fort Collins, Colorado 80525

Chaptpr I
97060A PTOdllct Information
Chapter 2
l)7060A Fm'IHlllnH'lltClI IllstClllatioll PM
Chapt(:'r 3
97060A Configuration
Chapter 4
97060A Troubleshooting
ChdptL'r 5
<-}7060A ()ia~Jnostics
Chapter 6
97060A Adjustments
Chaptpr 7
97060A Peripherals
Chapt(:'r S
97060A Replaceable Pents
Chapter 9
970bOA Diagrams
Chapter 10
97060A Referencps
Chapter 11
97060A Service Notps

ii
Printing History
The manual printing date and part number indicate its current edition. The printing date will change
when a new edition
is printed. Minor changes may be made at reprint without changing the printing
date. The manual part number
will change when extensive changes are made.
Manual updates may
be issued between editions to correct errors or document product changes. To
ensure that you receive these updates or new editions, you should subscribe to the appropriate
product support service.
See your HP sales representative for details.
January 1984
... First Edition

1-1
Chapter 1
97060A Product Information
Features
• LSIIVLSI bipolar and MOS technology
• Eight planes of 1024 X 1024 pixels
• 33 Hz or 60 Hz display mode refresh rate
• 256 colors displayed out of 16.7 million available
• 110V or 220V
• Extensive self-test capability
Resolution:
Horizontal Scan Rate:
Host Interface:
Tablet Interface:
Reset:
Rated
line Voltage:
Frequency Range:
Power Dissipated:
Supply Ratings:
Fuse:
Video:
Functional Specifications
1024 x 768 @ 33 Hz interlaced
736 x
552 (i:l 60 Hz non-interlaced
Other options are soft programmable, such as 640 x 480, 30 Hz, RS-170
28.3 kHz at 33 Hz vertical
35.4 kHz at 60 Hz vertical
Compatible with
HP 27112A General Purpose 1I0 (GPIO) Interface Card with
Option 001 interface cable
Compatible with
HP 9111A Data Tablet
Power up causes full self test
Host reset causes
full self test
Electrical Characteristics
Low Range:
High Range:
47 to 66 Hz
90 to 132 Vac
180 to 264 Vac
<100W; 85W typical
+5V @ 20A
-5V @ 12A
4A Low Voltage Range, fast blow
2A High Voltage Range, fast blow
RS-343 compatible; IV p-p with sync on Green; 0.7V video, 0.3V sync within
5%

1-2 97060A Product Information
Configuration
• Interfaces with HP 9000 Series 500 computer via HP 27112A GPIO interface card.
• Interfaces with HP 13279B Color Monitor or any other RS-343-compatible 19-inch color
monitor which can support the 97060A horizontal scan rate.
• Has built-in HP-IB interface which can communicate with the HP 9111A Graphics Tablet.
€}
N L
Australia Denmark Europe
~
N L
~
Switzerland United States
South Africa 120V
Power Cords
&§)
[QJ
••
L N
Great Britain
Q
L N
E
•
United States
240V
Country Part Number Opt. Voltage
Australia 8120-1369 901
250V, 6A
Denmark 8120·2956 912 250V, 6A
Europe 8120-1689 902 250V, 6A
Great Britain 8120-1351 900 250V, 6A
South Africa 8120-4211 917
250V,10A
Switzerland 8120-2104 906 250V. 6A
United States 8120-1378 903
120V,10A
United States 8120-0698 904
240V,10A
Power cords supplied by HP have polarities matched to the
power-input socket on the computer:
• L = Line or Active Conductor (also called "live" or
"hot")
• N Neutral or Identified Conductor
• E = Earth or Safety Ground
NOTE: Plugs are viewed from connector end. Shape of molded plug
may vary within country.
97060-90001
97060-90030
Related Documentation
HP 97060A Graphics Processor Installation Note
HP 97060A Graphics Processor Service Manual
Product Support Package
The 97060A requires no special tools for selVice.
Safety
WARNING
LETHAL VOLTAGES ARE PRESENT INSIDE THE 97060A. IF YOU
ARE UNFAMILIAR WITH THE 97060A. REFER TO THE WARNINGS
IN
THE SERVICE MANUAL.

Dimensions:
Temperature:
Humidity:
Altitude:
EM!:
Safety:
2-1
Chapter 2
97060A Environmental/Installation/
Preventive Maintenance
Environmental Specifications
Width: 17 inches
Height:
5.25 inches
Length: 21 inches
-40°C to +75°C non-operating
O°C to +55°C operating
+40°C @ 95% non-condensing operating
50,000 feet, 0-55°C, non-operating
15,000 feet, 0-55°C, operating
VDE Class A
FCC Class A
ULl14 (Office Machines)
UL478 (EDP)
CSA154 (EDP)
IEC380 (Office Machines with
Amendment 1)
IEC435 (EDP 1982)

E1
2-2 97060A Environmental Installation,PM
Installation Procedure
1. Ensure that the HP 27II2A GPIO interface card has its switches set as shown:
W1, W2, W3
Jumper in 5V Position
+5 r:i:!le + 12
Jumper in 12V Position
+5 e£I:!J+12
W1
GPIO Interface Card Switch Settings
2. Install the HP 27II2A GPIO card in an interface card slot in the computer or HP 97098A I/O
Expander. and connect the GPIO interface cable to the card.
3. Connect the other end of the GPIO cable to the 97060A connector labeled "J9/GPIO
HOST".
4. Interconnect the 97060A and the monitor with the three 1.8-metre BNC cables. red to red.
green to green.
and blue to blue.
5. Set the monitor so that the video signal is terminated with 75 ohms.
6. If you are installing the HP 911IA Data Tablet. connect an HP-IB cable from the 9I11A to
the 97060A input jack labeled
"JI0'GPIB TABLET'. Ensure that the 9IIIA device address
is set to 6 and that no other interface cable is connected to the 9IIIA.

97060A Environmental/Installation/PM 2-3
CAUTION
ENSURE THAT THE 97060A IS CONFIGURED TO MATCH THE
INPUT LINE VOLTAGE.
7. Connect power cords to the 97060A, the monitor, and optionally to the 9111A.
8. Turn on power to the computer, 97060A, monitor,
and optionally the 9111A.
9. If the computer is a Model 520, load the System Integrity Test and run the 97060 test.
10. If necessary, adjust the monitor's horizontal and/or vertical hold to get a stable picture.
Preventive Maintenance
There are no preventive maintenance procedures. Clean case parts as required according to the
following instructions.
CAUTION
CHEMICAL SPRAY-ON CLEANERS USED FOR APPLIANCES AND
OTHER HOUSEHOLD APPLICATIONS MAY DAMAGE THE FIN-
ISH. THESE
OR OTHER CHEMICAL CLEANERS SHOULD NOTBE
USED. DO NOT USE DETERGENTS THAT CONTAIN AMMONIA,
BENZENES, CHLORIDES,
OR ABRASIVES.
Clean case parts by wiping with a clean, lint-free cloth which has been dampened with a solution of
clean water and mild soap. A solution of 80% water and 20% isopropyl alcohol may be used for
heavily soiled areas.

2-4 97060A Environmental InstaIJationPM

3-1
Chapter 3
97060A Configuration
33/60 Hz Display Mode
Configure the controller pc assembly as shown in the following figure. Plug in jumpers to select 33
or 60 Hz frame refresh rate. The other four jumpers should be in the positions shown.
Controller Pc Assembly Jumpers
OR ~~:
• • •
60 HZ
•
JUMPER
033-001S8-00MET

3-2 97060A Configuration
Parallel Interface Pc Assembly
Ensure that the four parallel interface pc assembly jumpers are plugged as shown in the following
figure.
JUMPER
033-001S8-00MET
Parallel Interface Pc Assembly Jumpers

Description
Power cord
Fan
Line
fuse
97060A Configuration 3-3
Voltage Options
Voltage Configuration Part Numbers
nov
8120-1378
050-00342-00MET
2110-0055
220V
Country dependent
050-00694-00MET
2110-0002
OR
110V
(JUMPER
INSTALLED)
•
•
220V
(JUMPER
NOT INSTALLED)
JUMPER
084-01918-00MET
INSTALL JUMPER
IN
110V OR 220V POSITION
JUMPER
084-01917-00MET
Power Supply Voltage Jumpers

3-4 97060A Confi',Juratiol1

Symptom
Fan not running.
Fan running
and front panel red ON LED off.
LEDs 012 and D13 off.
Op codes don't function correctly.
• Each power supply has its own fuse
4-1
Chapter 4
97060A Troubleshooting
Probable Cause
Faulty line fuse.
Faulty +5V power supply. *
Faulty -5V power supply.*
Faulty parallel interface pc assembly.

4-2 97060A Troubleshooting

5-1
Chapter 5
97060A Diagnostics
Self Test
The built-in self test starts on powerup of the 97060A. The self test may be run with or without any
other device connected to the 97060A. If no errors are found, the green READY
LED on the front
panel lights after several seconds
and stays on after the self test is complete. If a monitor is
connected to the 97060A, a small star pattern is displayed on the CRT after the READY LED
lights.
The self test DOES:
• Detect more than 90% of IC failures.
• Check data bus counter.
• Check bit slice register increment.
• Check loop counter.
• Check 110 loopback.
• Check scratchpad RAM, load with address.
• Test memory; write all Is, Os, Is, Os; read back.
• Write mask, write data, check with read back.
• Test vector drawing followed by signature read.
The self test DOES
NOT:
• Detect 110 buffer errors.
• Detect some DAC errors.
• Detect internal RGB cable failures.
• Detect rear panel connector failures.

5-2 97060A Diagnostics
Diagnostic LEOs
Nine LEOs on the controller pc assembly indicate a more detailed definition of the failure. Most of
the failures are caused by a faulty controller pc assembly which should be replaced. The following
LEO configurations could result from other conditions:
• All LEOs "on" indicate self test passed.
• LEOs 012 and 013 "off" indicate a faulty -5V power supply.
• LEOs 09 and 011 "on" indicate an I/O problem. Check the following in the order indicated:
1. Parallel interface pc assembly not plugged in.
2. Parallel interface pc assembly failure.
3. Controller pc assembly failure.
System Integrity Test
The System Integrity Tests have a 97060 diagnostic. You can use this diagnostic if you have an HP
9000 Model 520 Computer and the System Integrity Tests.

There are no adjustments on the 97060A.
6-1
Chapter 6
97060A Adjustments

6-2 97060A Adjustments