HP KAYAK XM600 Parts list manual

Installing and Replacing Hardware
Parts in Your PC Workstation
This chapter provides information about installing accessories and
replacing hardware parts in your PC Workstation.
Contact your dealer for an up-to-date list of supported devices or check the
HP web site: http://www.hp.com/go/kayak.
Front Access Drives, for
- 5.25-inch drives
- 3.5-inch 1.44 MB
floppy disk drive
Front Access Cage
Up to six accessory cards can be
installed:
- One AGP 4X slot (graphics)
- Five 32-bit PCI slots
Support for one or two
processors
Depending on the model, the memory module sockets support either:
Primary Hard Disk
Drive Bay
Floppy Disk Drive Connector
Primary IDE Connector
Power Supply Unit
Processor Fan
Secondary
Hard Disk
Drive tray
HP UltraFlow
Airflow Guide
Secondary IDE Connector
HP Master Key Lock
•Two RDRAM modules.
•Two SDRAM modules installed in a Memory Expansion Card.
chapter2.fm Page 1 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing the Cover and Front Bezel
2
Removing and Replacing the Cover and Front Bezel
Removing the
Cover
For your own safety, it is recommended that you first read the warning
notices in the Introductory Section.
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2If necessary, unlock the cover using
the key on the front panel.
3Unscrew the thumb screw at the back of the PC.
4Push the two release latches inwards.
5Slide the cover towards the rear of the PC Workstation until it stops,
then lift off the PC chassis.
ê
➍
➍
➎
chapter2.fm Page 2 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing the Cover and Front Bezel
3
Removing the
Front Bezel
6If required, remove the front bezel. To remove the bezel:
aPush down on the two grey retaining clips.
bThen push the blue clip inwards.
cTilt the bezel forwards and lift it off.
Replacing the Cover
and Front Bezel
1Ensure that all internal cables are properly connected and safely routed.
2If necessary, replace the front bezel. To do this, align the three guide
pins located at the bottom of the bezel with their associated slots on the
front of the chassis and gently push forward until the bezel snaps into
place.
3Lower the cover onto the PC chassis (aligning the rails on the inside
edges of the cover with the sides of the PC chassis), and firmly slide the
cover forwards until it clicks into position.
4Tighten the thumb screw at the rear of the PC.
5If required, lock the cover using the key provided. Reconnect all the
power and telecommunications cables.
ab
c
a
c
chapter2.fm Page 3 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing the Airflow Guide
4
Removing and Replacing the Airflow Guide
Removing the HP
UltraFlow Airflow
Guide
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover (refer to page 2 for instructions).
3Slide the HP UltraFlow Airflow Guide towards the front access shelf.
4Lift the HP UltraFlow Airflow Guide upwards to remove it from the PC
Workstation’s case.
Replacing the HP
UltraFlow Airflow
Guide
1Lower the HP UltraFlow Airflow Guide.
2Slide the HP UltraFlow Airflow Guide towards the processor fan until it
clicks into place.
3Replace the PC Workstation’s cover (refer to page 3). Reconnect all the
power and telecommunications cables.
chapter2.fm Page 4 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing a Processor
5
Removing and Replacing a Processor
Single-processor systems can be upgraded to dual-processor systems by
installing a second processor in the vacant processor slot. The second
processor must be of the same type, speed and level-2 cache memory
capacity as the first.
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover (refer to page 2 for instructions).
3Remove the HP UltraFlow Airflow Guide (refer to page 4 for
instructions).
4If you intend to:
aRemove a Processor:
Press the retention clips on both sides of the processor outwards.
Then gently lift the processor upwards from the processor
connector, taking care not to tilt it too much.
bInstall a Second Processor:
Remove the processor terminator from the CPU 2 connector. Store
the terminator in a safe place. For information about upgrading the
operating system, refer to "HP DualExpress!", on page 6.
chapter2.fm Page 5 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing a Processor
6
Installing a
Processor
1Ensure that the edges of the processor are lined-up with the processor
connector guide rails along the retention mechanism.
2Place one hand on the processor’s heatsink and push down onto the
processor connector. You hear two clicks as the retention mechanism
pops back, thereby locking the processor into the processor connector.
3Replace the HP UltraFlow Airflow Guide (refer to page 4).
4Replace the PC Workstation’s cover (refer to page 3). Reconnect all the
power and telecommunications cables.
NOTE The processor type and speed is automatically recognized by the BIOS.
HP DualExpress!
Included with the HP Processor Accessory is the HP DualExpress!
application. This application is to be used when upgrading Windows NT 4
from a single-processor to a multi-processor system.
Using an installation Wizard, HP DualExpress! guides you through the
operating system upgrade which should take less than five minutes to
complete.
Launching HP
DualExpress!
The second processor must be installed and the PC booted. For now,
Windows NT will still only recognize the original processor. Insert the HP
DualExpress! floppy disk in the floppy disk drive and follow the
instructions. When the upgrade is complete, the system reboots. This time
a multi-processing system is recognized.
chapter2.fm Page 6 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing, Replacing and Upgrading Memory on Models Shipped with SDRAM
7
Removing, Replacing and Upgrading Memory
on Models Shipped with SDRAM
Upgrading SDRAM Memory
SDRAM models of the HP Kayak XM600 are supplied with a Memory
Expansion Card supporting one or two Synchronized Dynamic RAM
(SDRAM) 100 MHz memory modules.
NOTE Use only the HP memory modules provided for your PC model. If you want
to find out about available accessories for your PC, refer to the HP
Accessories Web site at: http://www.hp.com/go/pcaccessories.
If two memory modules are installed, and they do not have identical
capacities, then the module with the highest capacity must be installed in
the memory socket nearest to the system board.
If only one memory module is installed, it can be installed in either socket.
The unused socket should be left empty; no continuity module or
terminator is required.
The Memory Expansion Card is installed in a reserved memory socket on
the system board (the socket furthest from the processor(s)).
The two remaining memory sockets on the system board, RIMM0 and
RIMM1 must each contain a continuity module.
Removing and Replacing an SDRAM Module
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover (refer to page 2 for instructions).
3Remove the HP UltraFlow Airflow Guide to obtain access to the SDRAM
modules and sockets on the memory expansion card (refer to page 4 for
instructions).
NOTE Install memory modules directly onto the Memory Expansion Card
without removing it from the system board.
4To remove a memory module, open the two retaining clips and remove
the module out of the socket.
chapter2.fm Page 7 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing, Replacing and Upgrading Memory on Models Shipped with SDRAM
8
5To install a module, ensure that the two notches of the memory module
are aligned with those of the socket. With the two retaining clips open,
press the memory module completely into the socket. You hear two
clicks as the retaining clips click into position.
6Replace the HP UltraFlow Airflow Guide (refer to page 4 for
instructions).
7Replace the PC Workstation’s cover (refer to page 3). Reconnect all the
power and telecommunications cables.
8Check the HP Summary Screen to verify the new configuration (refer to
“Viewing the HP Summary Screen” in the Section on “Setting Up and
Using Your PC Workstation”)
Removing and Replacing the Memory Expansion Card
NOTE The unused memory sockets on the system board, RIMM0 and RIMM1
must contain a continuity module.
Removing the
Memory Expansion
Card
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover (refer to page 2 for instructions).
3Release the retaining screw located on the Memory Expansion Card.
Then remove the screw from accessory card socket.
4Open the two retaining clips on the system board to release the Memory
Expansion Card, then remove it from the connector.
5Remove memory modules from the old Memory Expansion Card, then
install them on the new Memory Expansion Card.
➍
➍➎
➎
chapter2.fm Page 8 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing, Replacing and Upgrading Memory on Models Shipped with SDRAM
9
Replacing the
Memory Expansion
Card
1Install the Memory Expansion Card so that the memory modules face the
processor.
2With the two retaining clips on the system board open, press the Memory
Expansion Card completely into its socket. Push inwards the two
latches on the memory socket to secure the Memory Expansion Card in
place.
3Tighten the retaining screw on the Memory Expansion Card and replace
the screw on the accessory card socket.
4Replace the PC Workstation’s cover (refer to page 3). Reconnect all the
power and telecommunications cables.
RIMM0 and RIMM1 sockets MUST contain
a continuity module
chapter2.fm Page 9 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing, Replacing and Upgrading Memory on Models Shipped with RDRAM
10
Removing, Replacing and Upgrading Memory
on Models Shipped with RDRAM
Upgrading RDRAM Memory
RDRAM models of the HP Kayak XM600 PC Workstation support one or
two RAMBUS Direct RAM (RDRAM) memory modules.
NOTE Use only the HP memory modules provided for your PC model. If you want
to find out about available accessories for your PC, refer to the HP
Accessories Web site at: http://www.hp.com/go/pcaccessories.
If only one RDRAM module is installed, it must be installed in the socket
nearest the processor(s).
If two RDRAM modules are installed, they must be installed in the two
sockets nearest the processor(s).
Any unused memory socket must contain a continuity module.
NOTE The system board may also have a third memory socket. This socket is
reserved uniquely for the SDRAM Memory Expansion Card supplied with
SDRAM models.
Removing and Replacing an RDRAM Module
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover (refer to page 2 for instructions).
3Remove the HP UltraFlow Airflow Guide (refer to page 4 for
instructions).
4To remove a memory module, open the two retaining clips and remove
the module out of the socket.
5To install a module, ensure that the two notches of the memory module
are aligned with those of the socket. With the two retaining clips open,
press the memory module completely into the socket. You hear two
clicks as the retaining clips click into position.
6Replace the HP UltraFlow Airflow Guide (refer to page 4 for
instructions).
7Replace the PC Workstation’s cover (refer to page 3). Reconnect all the
power and telecommunications cables.
chapter2.fm Page 10 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing, Replacing and Upgrading Memory on Models Shipped with RDRAM
11
8Check the HP Summary Screen to verify the new configuration (refer to
“Viewing the HP Summary Screen” in the Section on “Setting Up and
Using Your PC Workstation”)
chapter2.fm Page 11 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing a PCI Accessory Card
12
Removing and Replacing a PCI Accessory Card
The HP Kayak XM600 has five 32-bit 33 MHz PCI accessory card slots and
one AGP slot on the system board. The AGP slot accepts standard 25 W
AGP video cards.
NOTE Higher power AGP PRO video cards cannot be used in desktop models.
Hardware Protection on the system board ensures that the system is
protected against this.
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover (refer to page 2 for instructions).
3If you intend to:
aInstall an Accessory Card:
Unscrew and remove the slot panel. Store it in a safe place. If the slot
cover is tight, loosen the screws on the adjacent slots.
bReplace an Accessory Card:
Remove any cables connected to the accessory card. Remove the
screw that holds the old card in place and carefully pull it out.
NOTE Some cards may have preferred locations and special installation
instructions detailed in their manuals.
4Aligning the new card carefully, slide it into position, then press it firmly
into the slot and tighten the retaining screw.
5Install any other accessories before replacing the cover (refer to page 3).
Reconnect all the power and telecommunications cables.
chapter2.fm Page 12 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Installing Mass Storage Devices
13
Installing Mass Storage Devices
The PC has an integrated Ultra ATA-66 controller that supports up to four
IDE devices. Removable media IDE devices, such as CD-ROM drives, DVD
drives, tape drives and Zip drives, require front access. In addition to the
floppy disk drive, your PC can support another 3.5-inch internal device plus
two front-access 5.25-inch devices. Note that one front-access shelf may
already have a CD-ROM drive installed in it.
Refer to the drive’s manual to see if you must set jumpers or if there is a
special installation procedure to follow.
If you add an IDE Zip drive, hard disk drive, DVD drive, CD-ROM drive, CD-
RW drive, or tape drive, you need to connect it to power and data cables.
The data cables and connectors provided are shown below:
Cable with one 34-pin
connector for
3.5-inch Floppy Disk Drive
Floppy Disk Drive Connector
Primary IDE
Connector
Secondary IDE Connector
Two IDE data cables each
with two 40-pin connectors
for IDE Drives
Primary IDE cable supports
two Hard Disk Drives
Secondary IDE cable for access device
such as CD-ROM Drives or Zip Drives
Power Cable for 3.5-inch Floppy
Disk Drive
Power Cables for Hard Disk Drives, Zip
Drives, Tape Drives, CD-RW,
CD-ROM Drives and DVD drives
chapter2.fm Page 13 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Installing Mass Storage Devices
14
Which IDE Data
Connectors to Use
There are three data cables inside your PC Workstation. Two of these are
for IDE devices.
•The ATA IDE cable supports two IDE devices. This cable is connected
to the Primary IDE connector on the system board. The bootable hard
disk drive is connected to this cable via the MASTER connector. A
second hard disk drive could be installed by using the SLAVE connector.
•A second IDE drive cable supports two IDE devices. If you install a CD-
ROM drive, a DVD drive or a Zip drive, connect it to this cable.
•The third cable has one connector for a floppy drive.
The following table explains which data connectors you should use when
you install additional devices.
Before Installing an
IDE Hard Disk
Refer to the drive’s installation guide to check jumper settings or if there is
a special installation procedure to follow.
Examples of multiple IDE drive combinations
Configuration Connections to data cables
1 Hard disk drive 1. Bootable hard disk drive: Master connector, Primary IDE Cable
2 Hard disk drives 1. Bootable hard disk drive:
2. Second hard disk drive:
Master connector, Primary IDE Cable
Slave connector, Primary IDE Cable
1 Hard disk drive
1 CD-ROM drive
1. Bootable hard disk drive:
2. CD-ROM drive:
Master connector, Primary IDE Cable
Master connector, Secondary IDE Cable
2 Hard disk drives
1 CD-ROM drive
1. Bootable hard disk drive:
2. Second hard disk drive:
3. CD-ROM drive:
Master connector, Primary IDE Cable
Slave connector, Primary IDE Cable
Master connector, Secondary IDE Cable
1 Hard disk drive
1 CD-ROM drive
1 Zip drive
1. Bootable hard disk drive:
2. CD-ROM drive:
3. Zip drive:
Master connector, Primary IDE Cable
Master connector, Secondary Cable
Slave connector, Secondary IDE Cable
2 Hard disk drives
1 CD-ROM drive
1 Zip drive
1. Bootable hard disk drive:
2. Second hard disk drive:
3. CD-ROM drive:
4. Zip drive:
Master connector, Primary IDE Cable
Slave connector, Primary IDE Cable
Master connector, Secondary IDE Cable
Slave connector, Secondary IDE Cable
chapter2.fm Page 14 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Installing Mass Storage Devices
15
Before Installing a
SCSI Hard Disk
(Selected Models
Only)
If you are installing an additional SCSI drive, you should configure an
unused SCSI ID to this accessory. SCSI IDs range from 0 to 15 for
Ultrawide 16-bit SCSI. SCSI ID 0 is used by the first SCSI hard disk drive
and SCSI ID 7 is reserved for the integrated SCSI controller (the default for
narrow and wide SCSI devices).
NOTE You do not need to select a SCSI ID for Plug and Play SCSI hard disks
(SCSI hard disks that support the SCAM protocol).
The total length of the external SCSI cables should not exceed 3 meters
(approximately 10 feet).
You should assign an unused SCSI ID to the second SCSI hard disk drive
(for example, SCSI ID 1).
The SCSI ID is usually configured with jumpers on the SCSI hard disk drive.
Refer to the installation guide supplied with the drive for information on
selecting a SCSI ID.
Some internal SCSI disk drives may have termination resistors that must be
removed or disabled before installation in your PC Workstation. Refer to
the drive’s installation guide for more details and to see if there is a special
installation procedure to follow.
chapter2.fm Page 15 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing the Primary Hard Disk Drive
16
Removing and Replacing the Primary Hard Disk Drive
CAUTION Handle the hard disk drive with care. Avoid shocks and violent
movement as this can cause damage to the hard disk drive’s internal
components.
Make sure that you back up your files before you install a hard disk
drive. Refer to your operating system documentation for information on
how to do this.
Removing the
Old Drive
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover and front bezel (refer to page 3 for
these instructions).
3Remove the two retaining screws from the chassis located on the front
of the PC and pull the primary hard disk drive out of the hard disk drive
bay.
4Disconnect the data and power cables from the hard disk drive.
CAUTION Take care when handling the hard disk drive during installation. A one-
quarter inch drop can damage it.
Installing the
New Drive
1Connect the data and power connectors to the hard disk drive.
2Slide the new drive into the hard disk drive bay (with the correct
orientation) and tighten the two retaining screws you removed earlier.
3Replace the front bezel and PC Workstation’s cover (refer to page 3).
Reconnect all the power and telecommunications cables.
4Turn to page 25 to complete the installation.
chapter2.fm Page 16 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Installing a Second Hard Disk Drive
17
Installing a Second Hard Disk Drive
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover and front bezel (refer to page 3 for
these instructions).
3Remove the two retaining screws from the hard disk drive tray located
on the front of the chassis, then carefully slide the tray towards the rear
of the PC.
4Insert the new drive into the drive tray and secure it to the tray using the
screw provided with the hard disk drive tray. Only one screw is required.
5Carefully put the drive tray back into the PC, and secure it in position
using the two retaining screws that you removed earlier.
6Connect the power cable and the data cable to the rear of the new hard
disk drive. The connectors are shaped to go in one way only. If you
are not sure which connector to use, refer to "Installing Mass Storage
Devices", on page 13.
7Replace the front bezel and PC Workstation’s cover (refer to page 3).
Reconnect all the power and telecommunications cables.
8Turn to page 25 to complete the installation.
chapter2.fm Page 17 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Installing an Accessory in the Front Access Cage
18
Installing an Accessory in the Front Access Cage
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover and the front bezel (refer to page 2
for instructions).
3Remove the HP UltraFlow Airflow Guide (refer to page 4).
4Remove the retaining screw from the front access cage, and slide it
forwards until it stops.
5Disconnect the power and data cables from the installed drives.
6Lift the front access cage upwards and out from the PC. Place the cage
on a table/desk top.
7Remove the 5.25-inch plastic filler plate. Use a screwdriver to unclip the
two latches located on the left-hand side of the filler plate, then pivot it
out. Store the filler plate in a safe place for future use. Be very careful
not to hurt your fingers when you remove the plate.
8If the new drive has a tray, attach the drive to the front access cage.
Many devices, such as the HP Zip drive, require an HP-supplied tray
before they can be installed. CD-ROM drives do not require a tray.
9Slide the new drive into the shelf. Ensure that the front of the new drive
is aligned with an existent device or filler plate. Secure the drive in
position using the screws supplied with it.
chapter2.fm Page 18 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Installing an Accessory in the Front Access Cage
19
10 Put the front access cage back into the PC. The front access cage
retainers should be aligned with the chassis.
11 Connect the power and data cables to the installed devices. For
convenience, it is recommended to start from the bottom and work
upwards. The connectors are shaped to go in one way only. If you are
not sure which connector to use, refer to "Installing Mass Storage
Devices", on page 13.
12 Ensure that the two metal guides on the inside of the chassis on the
right-hand side are aligned with the two front access cage retainers.
Slide the front access cage towards the rear of the PC until it snaps into
place.
NOTE To verify that the front access cage is correctly in position, check that the
“Align “mark on top of the chassis is parallel with the one on top of the
chassis edge.
13 Secure the front access cage in position using the retaining screw you
removed earlier.
14 To allow access to the device, remove the plastic plate from the cover by
unclipping it on one side and pivoting it out. Store the plate in a safe
place.
15 Replace the HP UltraFlow Airflow Guide (refer to page 4).
chapter2.fm Page 19 Wednesday, December 8, 1999 6:56 PM

Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the CD-ROM Drive (or DVD-Drive)
20
16 Replace the front bezel and PC Workstation’s cover (refer to page 3).
Reconnect all the power and telecommunications cables.
17 Turn to page 25 to complete the installation.
Replacing the CD-ROM Drive (or DVD-Drive)
Removing the
Old Drive
1Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2Remove the PC Workstation’s cover and front bezel (refer to page 3 for
these instructions).
3Refer to page 18 for instruction on removing the front access cage.
Installing the
New Drive
1Slide the new drive into the drive tray (with the correct orientation).
Ensure that the front of the new drive is aligned with an existent device
or filler plate. Secure the drive in position.
2Put the front access cage back into the PC. The front access cage
retainers should be aligned with the chassis.
3Connect the power and data cables to the new drive and any installed
drives. The connectors are shaped to go in one way only.
4Ensure that the two metal guides on the inside of the chassis on the
right-hand side are aligned with the two front access cage retainers.
Slide the front access cage towards the rear of the PC until it snaps into
place.
NOTE To verify that the front access cage is correctly in position, check that the
“Align” mark on top of the chassis is parallel with the one on top of the
chassis edge.
5Secure the front access cage in position using the retaining screw you
removed earlier.
6Ensure that the data and power cables are neatly routed so that they do
not interfere with any other device or hinder the PC Workstation’s cover.
7Replace the HP UltraFlow Airflow Guide (refer to page 4).
8Replace the front bezel and PC Workstation’s cover (refer to page 3).
Reconnect all the power and telecommunications cables.
9Turn to page 25 to complete the installation.
chapter2.fm Page 20 Wednesday, December 8, 1999 6:56 PM