HP 27qi Installation instructions

EL-MF877-00 Page 1
Template Revision B
PSG instructions for this template are available at EL-MF877-01
Product End-of-Life Disassembly Instructions
Product Category: Monitors and Displays
Marketing Name / Model
[List multiple models if applicable.]
HP 27qi Display
HP 27qi 27-inch Display
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions
for the disassembly of HP products to remove components and materials requiring selective treatment, as defined by EU
directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).
1.0 Items Requiring Selective Treatment
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as
applicable.
Item Description Notes
Quantity
of items
included
in product
Printed Circuit Boards (PCB) or Printed Circuit
Assemblies (PCA)
With a surface greater than 10 sq cm
I/F Board*1, SPS board*1, Control Board*1
3
Batteries
All types including standard alkaline and lithium coin
or button style batteries
0
Mercury-containing components
For example, mercury in lamps, display backlights,
scanner lamps, switches, batteries
0
Liquid Crystal Displays (LCD) with a surface greater
than 100 sq cm
Includes background illuminated displays with gas
discharge lamps Panel*1
1
Cathode Ray Tubes (CRT)
0
Capacitors / condensers (Containing PCB/PCT)
0
0
Electrolytic Capacitors / Condensers measuring
greater than 2.5 cm in diameter or height
C605 in SPS Board
1
External electrical cables and cords
HDMI cable*1, Power cord*1
2
Gas Discharge Lamps
0
Plastics containing Brominated Flame Retardants
weighing > 25 grams (not including PCBs or PCAs
already listed as a separate item above)
0
Components and parts containing toner and ink,
including liquids, semi-liquids (gel/paste) and toner
Include the cartridges, print heads, tubes, vent
chambers, and service stations.
0
Components and waste containing asbestos
0
Components, parts and materials containing
refractory ceramic fibers
0

EL-MF877-00 Page 2
Template Revision B
PSG instructions for this template are available at EL-MF877-01
Components, parts and materials containing
radioactive substances
0
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where components
and materials requiring selective treatment can be removed.
Tool Description
Tool Size (if
applicable)
Screw driver
2
Hexagon Screw Driver
1
Flathead screwdriver
1
3.0 Product Disassembly Process
3.1 List the basic steps that should typically be followed to remove components and materials requiring selective treatment:
1. Use tool to release screws on monitor, then separate the Stand from monitor head
2. Use tool to release screws on monitor, then use tool to separate rear cover from monitor head through tear down slot.
3. Disassemble the lamp wire, LVDS FFC*2 and ctrl-BD FFC from connector, tear the tape*2 from chassis, separate
Assy- chassis from monitor head by hand.
4. Disassemble the lamp wire from panel, and disassemble ctrl-BD from MF by hand.
5. Use tool to release screws*9 on MF, then separate the MF from panel.
6. Use tool to release Hexagon screw*2 from SHD, then release screws*7 on the power board and interface board, then
disassemble power-BD and interface-BD from the chassis by hand.
7. Disassemble the LVDS*2 by hand.
8. Release Column & base by hand.
9. Use tool to release screw*3 from Column.
10.
11.
12.
13.
14.
15.
16.
3.2 Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items
contained in the product that require selective treatment (with descriptions and arrows identifying locations).
1. Use tool to release screws on monitor, then separate the Stand from monitor head

EL-MF877-00 Page 3
Template Revision B
PSG instructions for this template are available at EL-MF877-01
2. Use tool to release screws on monitor, then use tool to separate rear cover from monitor head through tear down
slot.
3. Disassemble the lamp wire, LVDS FFC*2 and ctrl-BD FFC from connector, tear the tape*2 from chassis, separate
Assy- chassis from monitor head by hand

EL-MF877-00 Page 4
Template Revision B
PSG instructions for this template are available at EL-MF877-01
4.Disassemble the lamp wire from panel, and disassemble ctrl-BD from MF by hand.
5. Use tool to release screws*9 on MF, then separate the MF from panel.

EL-MF877-00 Page 5
Template Revision B
PSG instructions for this template are available at EL-MF877-01
6. Use tool to release Hexagon screw*2 from SHD, then release screws*7 on the power board and interface board,
then disassemble power-BD and interface-BD from the chassis by hand.
7. Disassemble the LVDS*2 by hand.
8. Release Column & base by hand.

EL-MF877-00 Page 6
Template Revision B
PSG instructions for this template are available at EL-MF877-01
9. Use tool to release screw*3 from Column.