HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... User manual

installation
instructions
hp StorageWorks
SAN switch
rack mount kit
Second Edition (June 2003)
Part Number: AV–RU6YB–TE
This document provides step-by-step instructions for installing the SAN Switch 2/8, SAN Switch
2/16 or SAN Switch 2/32 using the hp StorageWorks SAN switch rack mount kit.
For the latest version of these Installation Instructions and other documentation, access the HP
storage website at:
http://www.hp.com/country/us/eng/prodserv/storage.html .

2 SAN Switch Rack Mount Kit Installation Instructions
© Copyright 1999-2003 Hewlett-Packard Development Company, L.P.
Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for
errors contained herein or for incidental or consequential damages in connection with the furnishing, performance,
or use of this material.
This document contains proprietary information, which is protected by copyright. No part of this document may be
photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard.
The information contained in this document is subject to change without notice.
BROCADE, the Brocade B weave logo, Brocade: the Intelligent Platform for Networking Storage, SilkWorm, and
SilkWorm Express, are trademarks or registered trademarks of Brocade Communications Systems, Inc. or its
subsidiaries in the United States and/or in other countries.
Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The
information is provided “as is” without warranty of any kind and is subject to change without notice. The warranties
for Hewlett-Packard Company products are set forth in the express limited warranty statements for such products.
Nothing herein should be construed as constituting an additional warranty.
Printed in the U.S.A.
SAN Switch Rack Mount Kit Installation Instructions
Second Edition (June 2003)
Part Number: AV–RU6YB–TE

3SAN Switch Rack Mount Kit Installation Instructions
About this Document
This document describes the installation of the SAN Switch 2/32, SAN Switch
2/16, and SAN Switch 2/8 in an HP Series 9000 or comparable EIA rack, or in an
HP System/e rack using the SAN Switch Rack Mount Kit, part number
331148-B21.
This section describes the content reflected in this document, including:
■Intended Audience, page 3
■Related Documentation, page 3
■Rack Stability, page 4
■Installation and Safety Guidelines, page 5
■Installing the Switch in a Rack Using the SAN Switch Rack Mount Kit,
page 8
Intended Audience
This book is intended for use by system administrators who are experienced with
the following:
■HP StorageWorks Fibre Channel SAN switches
■Fabric Operating System (FOS) V3.1.x or later
Related Documentation
For a list of related documents included with this product, see the Related
Documents section of the Release Notes that came with your switch.
For the latest information, documentation, and firmware releases, please visit the
following StorageWorks website:
http://www.hp.com/country/us/eng/
prodserv/storage.html .
For information about Fibre Channel standards, visit the Fibre Channel
Association website, located at:
http://www.fibrechannel.org .

4 SAN Switch Rack Mount Kit Installation Instructions
Rack Stability
Rack stability protects personnel and equipment.
WARNING: To reduce the risk of personal injury or damage to the
equipment, be sure that:
■The leveling jacks are extended to the floor.
■The full weight of the rack rests on the leveling jacks.
■In single rack installations, the stabilizing feet are attached to the rack.
■In multiple rack installations, the racks are coupled.
■Only one rack component is extended at any time. A rack may become
unstable if more than one rack component is extended for any reason.

5SAN Switch Rack Mount Kit Installation Instructions
Installation and Safety Guidelines
Read the following sections for installation guidelines. Install the SAN Switch in
one of the following ways:
■As a stand-alone unit on a flat surface.
■In an Electronics Industries Association (EIA) cabinet (like the HP 9000
Series Rack).
■In an HP System/e rack.
Selecting an Operating Location
To ensure correct operation of the switch, the location where the switch is in use
must meet the following requirements:
■Adequate supply circuit, line fusing, and wire size, as specified by the
electrical rating on the switch nameplate.
■An air flow of at least 300 cubic feet per minute, available in the immediate
vicinity of the switch.
■If installing the switch in the HP 9000 Series, or comparable EIA rack:
— All equipment installed in the rack should have a reliable branch circuit
ground connection, and should not rely on a connection to a branch
circuit, such as a power strip.
— The rack should be balanced and the installed equipment should be within
the rack’s weight limits. Ensure the rack is mechanically secured to insure
stability in the event of an earthquake.
Cooling Requirements
Cooling air is drawn into the switch chassis by the fans mounted on the rear of the
chassis. The air is expelled through vents in the front (port side) of the chassis,
next to the HP logo. HP recommends installing the switch so that air intake and
exhaust for all components in the rack is flowing in the same front-to-back
direction.
Note: HP highly recommends mounting the switch in a cabinet or rack so that the fans
reside in the front of the cabinet, and the ports (cables) reside in the rear of the cabinet.

6 SAN Switch Rack Mount Kit Installation Instructions
Follow these guidelines to ensure proper air flow, and prevent component
overheating:
■To ensure adequate cooling, install the switch with the non-port side,
which contains the air intake vents, facing the cool-air aisle.
■Verify a minimum of 47 cubic feet/minute (79.8 cubic meters/hour) of air
flow is available to the air intake vents on the non-port side of the switch.
■Verify that the ambient air temperature does not exceed 40° Celsius (104°
Fahrenheit) while the switch is operating.
Caution: Do not block air vents. The switch uses ambient air for cooling.
Power Requirements
The AC power source must meet these requirements:
■Primary AC Input 100–240 VAC (switch auto-senses input voltage) 47–63 Hz
■Correctly wired primary outlet, with circuit protected by a circuit breaker and
grounded in accordance with local electrical codes
■Adequate supply circuit, line fusing, and wire size, as specified by the
electrical rating on the switch nameplate
■Voltage capability of 85–264 VAC
■Input voltage frequency of 47–63 Hz
■Power capability of 75 W maximum
Rack Mount Checklist
Verify that the rack and the area around the rack meets the following
requirements:
■The cabinet must be a standard EIA cabinet.
■Plan a cabinet space that is 1.5 rack units high (2.6 inches; 6.7 cm), 19 inches
(48.3 cm) wide, and at least 23 inches (68.6 cm) deep.
■Ground all equipment in the cabinet through a reliable branch circuit
connection, and maintain ground at all times. Do not rely on a secondary
connection to a branch circuit, such as a power strip.

7SAN Switch Rack Mount Kit Installation Instructions
■Ensure that air flow and temperature requirements are met on an ongoing
basis, particularly if the switch is installed in a closed or multi-rack assembly.
■Verify that the additional weight of the switch does not exceed the cabinet’s
weight limits or unbalance the cabinet in any way.
■Secure the cabinet to insure stability in case of unexpected movement.
Note: For proper air flow, the SFP media side of the switch must face the rear of the
rack. This mounting allows air to enter from the front of the rack and to exhaust at the
rear of the rack, similar to other rack-mounted equipment. This prevents switch
overheating.

8 SAN Switch Rack Mount Kit Installation Instructions
Installing the Switch in a Rack Using the SAN Switch
Rack Mount Kit
This section provides instructions for installing the SAN Switch 2/32, SAN
Switch 2/16, or SAN Switch 2/8 in an HP System/e rack, or in an HP 9000 Series
or comparable EIA rack using the SAN Switch Rack Mount Kit, part number
331148-B21.
Figure 1: SAN Switch 2/16 rack-mounted switch
Note: The Rack Mount Kit installation requires one technician to install a SAN switch.
The following items are required to install the switch in a rack:
■SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8
■Power cables
■#2 Phillips screwdriver
■7/16-inch wrench or socket
■The SAN Switch Rack Mount Kit rails and rail mounting hardware listed
next:

9SAN Switch Rack Mount Kit Installation Instructions
(2) rear mounting brackets
A right inner rail and a right outer rail
A left inner rail and a left outer rail
(14) #8-32 x 3/16-inch Phillips pan-head
screw with thread lock
(10) #10-32 x 1/2-inch Phillips pan-head
screw with captive star lock washer
(8) #10 alignment washer
(8) #10 adapter washer
(2) 1/4-20 hex nut with captive star lock
washer
(2) 1/4-inch flat washer

10 SAN Switch Rack Mount Kit Installation Instructions
Caution: For proper air flow, the SFP media side of the SAN Switch 2/32,
SAN Switch 2/16, or SAN Switch 2/8 must face the rear of the rack. This
mounting allows air to enter from the front of the rack and to exhaust at the
rear of the rack, similar to other rack-mounted equipment. This prevents switch
overheating, which may cause it to fail.
To install the switch in a rack:
1. Check contents of the shipping carton to verify all the required parts and
hardware are available.
2. Choose a mounting location in the rack for the switch.
3. Attach the rear mounting brackets to the rear rack uprights by completing one
of the following steps:
— For an HP 9000 Series or comparable EIA rack, assemble each of the two
brackets with (2) #10-32 x 1/2-inch Phillips pan-head screws with captive
star lock washers and (2) #10 adapter washers as shown in Figure 2.
Figure 2: Installing the rear mounting brackets (HP 9000 Series or comparable EIA
rack)