HP SitePrint Robot User manual

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
HP SitePrint Robot
Assembly Instructions

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
What’s in the box
1. Prism hole space
2. Miniprism bipod
3. Battery
4. Extraction handle
5. HP SitePrint Robot
6. Spray bottle for cleaning
7. Ink supply slots
8. Battery holder
9. Charger and joystick cable
10. Remote control
11. Battery charger transformer
12. Battery charger
This product contains ítems classied as Dangerous Good for Transportation,
please refer to the User Guide for transportation guidelines.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Extract the HP SitePrint Robot from the box
a. Open the packaging and extract
the contents.
b. Hold the HP SitePrint Robot by the blue
handle and the rear handle and remove
it from the box by gently lifting it
upwards while keeping it horizontal.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Insert the battery
Before inserting the battery make sure it’s fully charged.
a. Take the battery holder and
the battery and locate the pins
on the battery.
b. Push them into the pin holders
on the holder and clip the
battery into place.
Note: Parallel grooves will remain
visible during the process.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Insert the battery
a. Press the button with your thumb to
open the lock and insert the battery
holder into the HP SitePrint Robot.
Once in place, release the button.
b. Support the HP SitePrint Robot with the
rear handle or wheel and gently push
the battery holder to fully lock it into
place.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Insert the ink cartridge
a. With the robot in the
horizontal position, or
rotated 45º: Open the
door.
Do not rotate the robot more
than 45º as the sensors can be
damaged if placed vertically.
b. Insert a color cartridge. c. Push the cartridge to the
right to lock it into place.
d. Close the door.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Insert the prism
a. Remove the extraction handle
from of the HP SitePrint Robot.
b. Insert and screw in the 360º prism.
Store the handle in the suitcase
prism-slot.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Recommendations
Do not lean on the HP Site-
Print Robot when manipulating
it as the caster wheels could
break.
Do not place the HP
SitePrint Robot vertically as it
could fall.
Note that the fragile areas
of the HP SitePrint Robot are:
the caster wheel, printhead and
frontal sensors. Always handle
the with care to protect them.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Switch on the HP SitePrint Robot
a. Turn on the HP SitePrint
Robot and wait for the
LEDs to turn white.
b. Four red LED signs are
seen projected in the
front and rear of the HP
SitePrint Robot.
c. If the LEDs turn orange
or red at the end of the
process, reboot the
system.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Switch on the control panel
Turn on your device.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Connect to the HP SitePrint Robot’s Wi-Fi
Connect to the HP SitePrint Robot’s Wi-Fi with the provided password; read the QR
code provided on the label to connect. The Wi-Fi name corresponds to the robot’s
serial number, found at the back of the QR card. You can also check the serial num-
ber at the base of the robot , on the label near the printhead.

NEED ILUSTRATION!!!
© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Access the control panel
a. Access the control panel user-interface from a Google
Chrome Browser by navigating to http://192.168.10.1.
b. Check the network connectivity.
Only Google Chrome
Browser is supported.

NEED ILUSTRATION!!!
© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Assign the robot to your account
Sign into HP SitePrint and assign the robot to your account.

NEED ILUSTRATION!!!
© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Introduce user ID
Introduce your user ID.

NEED ILUSTRATION!!!
© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Register the HP SitePrint Robot
Register the HP SitePrint Robot.

NEED ILUSTRATION!!!
© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Get started
Click Get started and follow the on-screen instructions.

NEED ILUSTRATION!!!
© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
Get started
Before using the HP SitePrint Robot for the rst time, you must install the latest software update.
This can be found in the Support menu tab > Software updates menu.

© Copyright 2023 HP Development Company, L.P. The information contained herein is subject to change without notice.
You are set up and ready to work
on your rst project!