HP Integrity rx2600 User manual

Getting Started Guide
HP Integrity rx2600 server and
HP workstation zx6000
Document Part Number: A9664-90030
July 2004
This guide provides an overview of the system front and rear panel
connectors, instructions on how to set up and configure your system,
and troubleshooting tips. The appendix includes regulatory notices.

ii HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Contents
© 2004 Hewlett-Packard Company
Microsoft®, Windows®, Windows 2000®, and Windows XP®are registered
trademarks of Microsoft Corporation in the U.S. and other countries.
Intel®and Itanium®are registered trademarks of Intel Corporation in the U.S.
and other countries.
All other product names mentioned herein may be trademarks of their respective
companies.
Hewlett-Packard Company shall not be liable for technical or editorial errors or
omissions contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material. The
information in this document is provided “as is” without warranty of any kind,
including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose, and is subject to change without notice. The
warranties for HP products are set forth in the express limited warranty
statements accompanying such products. Nothing herein should be construed as
constituting an additional warranty.
This document contains proprietary information that is protected by copyright.
No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Hewlett-Packard
Company.
ÅWARNING: Text set off in this manner indicates that failure to follow
directions could result in bodily harm or loss of life.
ÄCAUTION: Text set off in this manner indicates that failure to follow
directions could result in damage to equipment or loss of information.
Getting Started Guide
HP Integrity rx2600 server and HP workstation zx6000
Second Edition (July 2004)
Document Part Number: A9664-90030

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide iii
Contents
Important Safety Warnings
ÅWARNING: Avoiding Electrical Shocks. To avoid electrical shock, do not
open the power supplies. There are no user-serviceable parts inside.
To avoid electrical shock and harm to your eyes by laser light, do not
open the DVD laser module. The laser module should be serviced by
service personnel only. Do not attempt to make any adjustment to the laser
unit. Refer to the label on the DVD for power requirements and
wavelength. This product is a class I laser product.
ÅWARNING: Removing and Replacing the Cover. For your safety, never
remove the system side cover without first disconnecting the power cord
from the power outlet and removing any connection to a
telecommunications network. If a Power Protection Device is fitted to your
system, you must shut down your computer using its on/off switch, then
remove the power cord before removing the system’s side cover. Remove
the Power Protection Device cables before any servicing operation. Always
replace the side cover before switching the system on again.
ÅWARNING: Battery Safety Information. There is a danger of explosion if
the battery is incorrectly installed. For your safety, never attempt to
recharge, disassemble, or burn an old battery. Replace the battery with
the same or equivalent type, as recommended by the manufacturer.
The battery in this system is a lithium battery that does not contain any
heavy metals. However, to protect the environment, do not dispose of
batteries in household waste. Return used batteries either to the shop from
which you bought them, to the dealer from whom you purchased your
system, or to HP so that they can either be recycled or disposed of in the
correct way. Returned batteries are accepted free of charge.
ÅWARNING: Avoiding Burn Injuries. Some parts inside the computer will
be hot. Wait approximately three to five minutes for them to cool down
before touching them.

iv HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Contents
ÄCAUTION: Avoiding Static Electricity. Static electricity can damage
electronic components. Turn OFF all equipment before installing an
accessory card. Don’t let your clothes touch any accessory card. To
equalize the static electricity when replacing an accessory card, rest the
accessory card bag on top of the system unit while you are removing the
card from the bag. Handle the card as little as possible and with care.
ÄCAUTION: Information on Ergonomic Issues. It is strongly recommended
that you read the ergonomics information, available in the “Working In
Comfort” section of this manual, before using your system. You can access
more extensive ergonomics information at: www.hp.com/ergo.
NOTE: Recycling Your System. HP has a strong commitment toward
the environment. Your HP system has been designed to respect the
environment as much as possible. HP can also take back your old
system for recycling when it reaches the end of its useful life. HP has
a product take-back program in several countries. The collected
equipment is sent to an HP recycling facilities in Europe or the U.S.A.
As many parts as possible are reused. The remainder is recycled.
Special care is taken for batteries and other potential toxic substances,
these are reduced into non-harmful components through special
chemical processes. If you require more details about the HP product
take-back program, contact your local dealer or your nearest HP Sales
Office.

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide v
Contents
1 Setting Up and Using Your System
System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
Setting Up Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7
Connecting Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8
Starting and Stopping Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–10
Starting Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–10
turning off Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11
Installing Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–12
Firmware and Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–13
Configuring Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14
Extensible Firmware Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14
Management Processor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–25
Baseboard Management Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–26
2Troubleshooting
Your System Does Not Start Properly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
You Find a Hardware Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
You Forgot the EFI Password(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
Troubleshooting with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
Troubleshooting with the e-buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
the System Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
Software Diagnostics Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–13
HP e-DiagTools Hardware Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–13
Restoring the OS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–18

vi HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Contents
Where to Get Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–19
Information to Collect Before You Contact Support . . . . . . . . . . . . . . . . . . . . . . 2–19
Online Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–20
Phone Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–20
Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–21
A Regulatory Information
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–2
Federal Communications Commission Radio Frequency Interference Statement
(for USA only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–3
Notice for Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–3
Safety Warning for the USA and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–3
Notice for France. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–4
Notice for the Netherlands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–4
Notice for Germany. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–4
Noise Declaration for Germany . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–5
Notice for Japan (Class A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–5
Notice for Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–5
Notice for Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–5
Index

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide 1–1
1
setting up and using your system
This chapter includes:
■descriptions of the system front and rear panels
■information on how to set up your system
■instructions for starting and stopping your system
■basic system configuration information
system configurations
The HP Integrity rx2600 server and HP workstation zx6000 are
available in tower and rack-mount configurations.
Configuration
Accessory
Slots
Fan Type/
Speed
Management
Processor
Redundant
Hot-swap
Power
Supply
workstation zx6000
tower 3 PCI 1 AGP Quiet/ Low No No
workstation zx6000
rack-mount 3 PCI 1 AGP Hi Capacity/ High Optional Optional
Integrity rx2600 server
tower 4 PCI Hi Capacity/ High Yes Yes
Integrity rx2600 server
rack-mount 4 PCI Hi Capacity/ High Yes Yes

1–2 HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Setting Up and Using Your System
front panel
The front panels of the rx2600 and zx6000 have the following
features:
■Power LED is green when the power is on, or the power button is
pushed in. If the power is on and the button is pushed in, the light
stays on even after the system is powered down. When the button
is released, the green light turns off.
■Power Button turns the system power on and off.
■LAN LED indicates the system is communicating over the
Gigabit or System Management LAN.
■System and Diagnostic LEDs identify system errors on
workstation zx6000s with no MP card installed.
■Locator LED and Button (rack-mount configuration only)
identify the rack position of the system.
■Disk Activity LEDs on each hard drive turn green when the disk
is accessed.
■e-buzzer icon indicates the position of the internal speaker.

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide 1–3
Setting Up and Using Your System
Front Panel, Tower Configuration
Front Panel, Rack-mounted Configuration
5
4
7
6
3
1
3 2 4 5
6
7 1
1 e-buzzer Icon 5 System LED
2 Locator LED and Button
(rack-mounted system only) 6Power Button
3 Diagnostic LEDs 1-4
(active only on workstation zx6000s
with no MP card installed)
7Power LED
4 LAN LED

1–4 HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Setting Up and Using Your System
rear panel
The rear panel has the following features:
■Connectors are shaped to go in one way only to prevent improper
cable attachment.
■Ports are labeled for easy identification.
■Management Processor (MP) ports are positioned above
(rack-mount) or to the right of (tower) standard connectors
(optional on workstation zx6000).
■LAN LEDs provide additional information:
❏Four Gigabit LAN LEDs
❏Two System Management 10/100 LAN LEDs
❏Four MP LAN LEDs (optional on workstation zx6000)
■Monitor Connector (on graphics card). workstation zx6000s
may include graphics cards with single or multiple monitor
support.
■Locator LED (rack-mount configuration only) identifies the rack
position of the system.

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide 1–5
Setting Up and Using Your System
Rear Panel Connectors
135 6 72 4
13 11 810 9
12
14
1Power (PWR2) 8USB ports
(mouse and keyboard
ports labelled)
2 Power (PWR1) 9TOC button
3 MP VGA, serial, LAN, reset
(optional on workstation zx6000)
10 Locator LED and button
4System lock 11 10/100 LAN
5Serial port A (console) 12 LAN LEDs
6Serial port B 13 10/100/1000 LAN
7Monitor connector(s)
(workstation zx6000 only) 14 LVD/SE SCSI

1–6 HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Setting Up and Using Your System
setting up your system
ÅWARNING: If you have any doubt that you can lift the system or monitor
safely, do not try to move them without help.
1. Check the materials list shipped with your system to verify that
you have all of the components.
2. Position the system so that its rear connectors are easily
accessible:
❏If the system is a tower configuration, place the system in an
area with easily accessible power outlets and enough space
for the keyboard, mouse, and any other accessories.
❏If the system is to be rack-mounted, refer to the mounting
instructions provided with your system.

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide 1–7
Setting Up and Using Your System
tools
You do not need any tools to set up your system. If you plan to install
additional hardware components, you need:
■Flat blade screwdriver
■T-15 Torx driver
■Special processor tool (provided with processor)
■Static-free mat
■Static strap
ÅWARNING: Metallic particulates can be especially harmful around electronic
equipment. This type of contamination may enter the data center environment
from a variety of sources, including, but not limited to, raised floor tiles, worn
air conditioning parts, heating ducts, rotor brushes in vacuum cleaners or
printer component wear. Because metallic particulates conduct electricity, they
have an increased potential for creating short circuits in electronic equipment.
This problem is exaggerated by the increasingly dense circuitry of any
electronic equipment.
Over time, very fine whiskers of pure metal can form on electroplated zinc,
cadmium, or tin surfaces. If these whiskers are disturbed, they may break off
and become airborne, possibly causing failures or operational interruptions. For
over 50 years, the electronics industry has been aware of the relatively rare, but
possible, threat posed by metallic particulate contamination. During recent
years, a growing concern has developed in computer rooms where these
conductive contaminants are formed on the bottom of some raised floor tiles.
Although this problem is relatively rare, it may be an issue within your computer
room. Since metallic contamination can cause permanent or intermittent failures
on your electronic equipment, Hewlett-Packard strongly recommends that your
site be evaluated for metallic particulate contamination before installation of
electronic equipment.

1–8 HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Setting Up and Using Your System
connecting devices
Before connecting any cords or cables to your system, please read the
Warning Notices in the front of this manual.
keyboard, mouse and power
The rx2600 and zx6000 systems ship with a USB keyboard and
mouse.
»Plug the keyboard and mouse into USB connectors on the rear
panel of the computer. (Ports are labelled.)
There are two power receptacles on the rear panel of the system.
»If you purchased your system without a second power supply,
cover the second receptacle (PWR2) with a plastic cap.
ÅWARNING: For your safety always connect equipment to a grounded wall
outlet. Always use a power cord with a properly grounded plug, such as the
one provided with the system, or one in compliance with your national safety
standards. This equipment can be disconnected from the power by removing
the power cord from the power outlet. The equipment must be located close to
an easily accessible power outlet.

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide 1–9
Setting Up and Using Your System
graphics cards and monitors
Integrity rx2600 servers and workstation zx6000s with Management
Processor (MP) cards support a VGA monitor connected to the VGA
port on the MP card.
workstation zx6000s with no MP cards are available with a range of
AGP graphics cards.
■Graphics cards may include an 15-pin connector, an 18-pin
connector, or both. Only one connecting cable is needed for each
monitor.
■Some video cards are pre-installed in the system, while others are
packaged separately and shipped with the system. If your
workstation did not ship with a pre-installed graphics card, you
must install the card and load the drivers. Refer to the
documentation included with your graphics card for instructions.
■Frequencies of 85Hz and higher provide flicker-free viewing.
■If the monitor you select is DDC-2B or DDC-2B+ compliant, the
graphics card automatically limits itself to those resolutions and
frequencies supported by that monitor. In this case, you do not
need to use the tables to select your monitor.
■For a complete and current list of supported cards with supported
display resolutions and frequencies, see:
❏http://partsurfer.hp.com
ÄCAUTION: To prevent possible damage to your monitor, make sure you select
a monitor that supports the resolutions and frequencies you wish to use.
■For more detailed information about your graphics card, see the
manufacturer’s web site:
❏ATI: www.ati.com
❏NVIDIA: www.NVIDIA.com

1–10 HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Setting Up and Using Your System
starting and stopping your system
HP Integrity rx2600 servers and workstation zx6000s come in many
different configurations. Pay careful attention to the directions below
and choose the options that match the OS and packaging you
purchased.
starting your system
To start your system:
1. Turn on the monitor before you start your system.
2. Press the power button on the front panel. The system starts.
During system startup, the display may remain blank for up to
one minute. This is normal.
If the system has an MP card, the system light blinks.
If the system does not have an MP card, the following should
occur:
❏Power LED turns on
❏System LED blinks on and off
❏On workstation zx6000s with no MP card installed,
diagnostic LEDs 1-4 create scrolling pattern
3. If you are prompted for a password, type it and press Enter.
The prompt displays only if you have set a password using the
Extensible Firmware Interface (EFI). (See “Management
Processor” on page 1-25.)

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide 1–11
Setting Up and Using Your System
initializing your software
The rx2600 and zx6000 can be configured with the Operating System
(OS) pre-installed or packaged separately.
■If you purchased a system with the OS pre-installed, the
initialization process starts when you start the workstation for the
first time.
The software initialization process takes a few minutes. You can
change the settings after the software has been initialized.
ÄCAUTION: Do NOT switch OFF the system while the software is being
initialized — this could cause unexpected results.
The initialization process:
❏Displays the license agreement.
❏Asks questions about the system.
■If you purchased a system and the OS is not pre-installed, install
the OS now:
❏HP-UX: Follow the instructions on the HP-UX CD envelope.
❏Linux: Use the HP Enablement Kit for Linux CD and follow
the instructions in its accompanying booklet.
❏Windows: Windows is always pre-installed on workstation
zx6000s. Use the HP Smart Setup DVD to begin the software
setup process on Integrity rx2600 servers.
turning off your system
To turn off the system:
1. Exit all applications.
2. Execute the Shut Down command provided by your OS.
3. When prompted, press the power button on your system.
NOTE: You can also shut down using the power button on the
system. When you press the power button, the OW shuts down and
the power turns off.

1–12 HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Setting Up and Using Your System
installing hardware components
If you purchased an accessory card, a graphics card, or other
hardware components that were not installed in your system at the
factory, you must install those components now.
ÅWARNING: For most hardware installation procedures, you must power off
the system and unplug the power cord from the outlet.
NOTE: To maintain FCC/EMI (Electromagnetic Interference)
compliance, replace all covers and make sure all screws are properly
seated after you replace components.
1. If you have already connected and turned on the system, turn off
the system and disconnect all cables from the rear panel.
2. Remove the system access covers.
3. Install the new components:
❏See the Installation Poster provided with your system for the
location of internal components.
❏For detailed instructions on installing hardware components,
see the hp rx2600/zx6000 Operation and Maintenance Guide.
4. Replace the system access covers.
5. Connect the system.

HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide 1–13
Setting Up and Using Your System
firmware and drivers
To download the latest drivers and firmware for your:
1. Go to: http://www.hp.com/go/bizsupport
Follow the menu prompts to navigate to the support page:
◆Select download drivers/software.
◆Enter the product name in the search field (rx2600 or
zx6000).
◆Select the search result.
◆Choose the driver or firmware upgrade you need to
download.
◆Click the i information icon for instructions on how to
download, unpack, and install the driver or firmware
upgrade.
These web sites contain a wide range of free information, including
downloadable documentation, service and support options, and the
latest versions of drivers and utilities. You also can obtain instructions
on how to upgrade firmware and register to automatically receive
information on new driver availability.

1–14 HP Integrity rx2600 server and HP workstation zx6000 Getting Started Guide
Setting Up and Using Your System
configuring your system
Three tools are available to configure your system:
■Extensible Firmware Interface (EFI), page 1-14
■Management Processor (MP) (optional on workstation zx6000s),
page 1-25
■Baseboard Management Controller (BMC), page 1-26
This section provides a brief introduction to these tools. For complete
information, refer to “System Configuration” in the hp rx2600/zx6000
Operation and Maintenance Guide.
extensible firmware interface
The Extensible Firmware Interface (EFI) is an interface that allows
you to configure the Itanium Processor Family (IPF) firmware. The
EFI menu includes the following options:
■The EFI Shell [Built-in] is a command line interface that allows
you to operate the EFI commands or create and run automated
scripts. See page 1-17.
■Boot Option Maintenance Menu allows you to select the
order of the devices from which you want the firmware to attempt
to boot the OS. You can also configure the system to boot from a
configuration file. See page 1-20.
■On systems with EFI firmware version 2.0 or higher, the System
Configuration Menu lets you view the system configuration
and change or delete administrator and user passwords. See
page 1-22.
■On systems with EFI firmware version 1.9 or lower, the
Security/Password Menu lets you add, change and delete
system administrator and user passwords. See page 1-25.