HP L1000 - 9000 - 0 MB RAM Owner's manual

Safety and Regulatory Information
hp server rp54xx
E0901
Compliance Model Number RSVL-0105-A
Manufacturing Part Number:A5191-96017
Fourth Edition
© Copyright 2001

2 English
Notice
Hewlett-Packard makes no warranty of any kind with regard to this material, including but not
limited to, the implied warranties of merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is
not furnished by Hewlett-Packard.
All rights are reserved. No part of this document may be photographed, reproduced, or translated to
another language without prior written consent of Hewlett-Packard Company.
The information contained in this document is subject to change without notice.
Printing History:
First edition: ------------------------ July 1999
Second edition: --------------------- April 2000
Third edition: ----------------------- January 2001
Fourth edition: ----------------------September 2001

English 3
hp server rp54xx System Safety and Regulatory Information
Overview
Regulatory Compliance statements are required by some countries for international importation of
hp server rp54xx products. The following information is provided:
Regulatory Information
Electrical Safety
— Electrostatic Discharge (ESD) Precautions
— Battery Notice
Cabinet Safety Precautions
Declaration of Conformity
FCC Statement (USA Only)
Canada RFI Statement
European Union RFI Statement
Acoustics (Germany)
Australian C-Tick Label
Laser Safety
Product Information
For detailed information on the hp server rp54xx products, please go to the http://docs.hp.com web site
(in the Systems Hardware selection).
Regulatory Information
For your protection, this product has been tested for conformance to various national and international
regulations and standards. The scope of this regulatory testing includes electrical and mechanical safety,
electromagnetic emissions, immunity, acoustics and hazardous materials.
When required, approvals are obtained from third party test agencies. Approval marks appear on the
product label. In addition, various regulatory bodies require some information under the headings listed
in this section.
Electrical Safety
This product has not been evaluated for connection to an “IT” power system (AC distribution system
having no direct connection to earth according to IEC 60950).
Locate the AC outlet near the computer! The AC power cords are this product's main AC disconnect
devices and must be easily accessible at all times.

4 English
Electrostatic Discharge (ESD) Precautions
When handling any electronic component or assembly (such as, a PCI card or Memory SIMM), you
must observe the following antistatic precautions to prevent damage. An ESD kit (HP P/N
A3024-80004) is available (or supplied with Memory additions). This kit contains one wrist strap, one
conductive sheet, and one anti-static foam pad.
• Always wear a grounded wrist strap when working around the system, and when handling printed
circuit boards.
• Treat all assemblies, components and interface connections as static-sensitive.
• Avoid working in carpeted areas, and keep body movement to a minimum while removing or
installing boards, to minimize buildup of static charge.
Battery Notice
This product contains a Lithium battery.
This battery is not to be removed or replaced by the user. If the battery needs to be replaced, contact your
Hewlett-Packard authorized service personnel.
CAUTION Lithium batteries may explode if mistreated.
Do not recharge, disassemble, or dispose of in a fire.
Please properly recycle all used batteries.

English 5
Cabinet Safety Precautions
WARNING Cabinets are heavy even when empty. Exercise caution when moving cabinets
whether equipment is installed in the cabinet or not. Avoid rolling cabinets on rough
or uneven surfaces or inclines greater than 10 degrees. Unloading cabinets from the
pallet and movement of cabinets should be performed by at least two people.
WARNING Slideable products are not to be extended from the cabinet while the equipment is on
the shipping pallet. The cabinet must be unloaded from the pallet and both front
and rear anti-tip feet properly installed prior to extending any slideable product.
WARNING Once installed, both the front and rear anti-tip feet must remain in place to maintain
stability. Only one slideable product must be extended at a time.
WARNING Use of any slide mount product requires the installation of a cabinet anti-tip device.
The anti-tip device for the following cabinet products is a pair of anti-tip feet:
A4900A, A4901A, A4902A, A5134A, A5135A, A5136A, J1500A, J1501A, and
J1502A.
Install both front and rear anti-tip feet on the cabinet before installing any slide
mount product.
The anti-tip device for the following cabinets is the installation of ballast in the
bottom of the cabinet: A1896A, A1897A, A1883A, A1884A, C2785A, C2786A, and
C2787A.
To determine ballast requirements, refer to the ballast worksheets in documentation
accompanying the cabinet or docs.hp.com.
Failure to follow these precautions can result in damage to equipment or injury to
personnel.

6 English
Procedimentos de Segurança - Armários
ATENÇÃO Os armários são pesados, mesmo quando vazios. Tenha cuidado ao movimentar os
armários, quer haja equipamentos instalados quer não. Evite deslizar os armários
sobre superficies acidentadas, irregulares ou com inclinação superior a 10 graus. A
retirada dos armários do palete e sua movimentação deverão ser feitas por, no
mínimo, duas pessoas.
ATENÇÃO Partes deslizantes não deverão ser abertas enquanto o armário encontrar-se no
palete de embarque. O armário deve ser descarregado do palete e os anteparos nos
pés dianteiros e traseiros devem ser instalados adequadamente antes de se abrir
qualquer parte deslizante.
ATENÇÃO Uma vez instalados, tanto os anteparos nos pés dianteiros quanto nos traseiros
devem permanecer em seus lugares adequados para garantir a estabilidade da peça.
Deve-se abrir apenas uma parte deslizante por vez.
ATENÇÃO O uso de qualquer produto de montagem deslizante requer a instalação de um
dispositivo anti-tombamento para armários.
Um par de pés anti-tombamento é o dispositivo anti-tombamento para os seguintes
armários: A4900A, A4901A, A4902A, A5134A, A5135A, A5136A, J1500A, J1501A,
e J1502A.
Instalar ambos os pés anti-tombamento na frente e atrás do armário antes da
instalação de qualquer produto de montagem deslizante.
A instalação de um lastro no fundo do armário é o dispositivo anti-tombamento para
os seguintes armários: A1896A, A1897A, A1883A, A1884A, C2785A, C2786A, e
C2787A.
Para determinar os requisitos de lastro, referir-se a planilha de lastro na
documentação que acompanha o armário ou em www.eproducts.hp.com
A não observância destas precauções pode resultar em danos ao equipamento ou
lesões as pessoas.

English 7
Säkerhetsföreskrifter för kabinett
VARNING Kabinetten är tunga även när de är tomma. Var försiktig när du flyttar ett kabinett,
oavsett om det är tomt eller innehåller utrustning. Undvik att rulla kabinett på ett
underlag som är ojämnt eller lutar mer än 10 grader. Det krävs minst två personer
för att lasta av ett kabinett från transportpallen eller för att flytta det.
VARNING Inskjutningsbara produkter får inte vara utdragna när utrustningen befinner sig på
transportpallen. Kabinettet måste lastas av från pallen och tippskyddsfötter ska
monteras både fram- och baktill innan en inskjutningsbar produkt dras ut.
VARNING Efter montering ska tippskyddsfötterna sitta kvar både fram- och baktill så att
stabiliteten upprätthålls. De inskjutningsbara produkterna får bara dras ut en i
sänder.
VARNING Kabinettet måste tippskyddas för att en inskjutningsbar produkt ska kunna
användas.
För följande kabinettprodukter ska två tippskyddsfötter användas: A4900A,
A4901A, A4902A, A5134A, A5135A, A5136A, J1500A, J1501A och J1502A.
Installera både den främre och den bakre tippskyddsfoten på kabinettet innan du
installerar en inskjutningsbar produkt.
Följande kabinett tippskyddas genom att ballast placeras i kabinettets botten:
A1896A, A1897A, A1883A, A1884A, C2785A, C2786A och C2787A.
I kabinettets dokumentation finns specifikationer för ballast. Du kan också gå till
www.eproducts.hp.com
Om dessa föreskrifter inte följs föreligger risk för personskada eller skada på
utrustningen.

8 English
Voorzorgsmaatregelen voor de veiligheid voor kasten
WAARSCHUWING Kasten zijn zwaar, ook als deze leeg zijn. Ga voorzichtig te werk als u een
kast verplaatst, of er nu wel of niet apparatuur in de kast is geïnstalleerd.
Rol kasten niet over ruwe of ongelijke oppervlakken of hellingen van meer
dan 10 graden. Als u een kast van een pallet moet afhalen of moet
verplaatsen, doet u dat dan altijd met twee personen.
WAARSCHUWING Zorg ervoor dat er geen uitschuifbare onderdelen uit de kast uitsteken als
de apparatuur ter verzending op een pallet is geplaatst. Voordat u een
uitschuifbaar onderdeel uitschuift, moet u de kast eerst van het pallet halen
en de stabilisatiesteunen aan de voor- en achterkant op de juiste manier
installeren.
WAARSCHUWING Zodra de kast is geïnstalleerd, mogen de stabilisatiesteunen niet meer
worden verplaatst. U mag niet meer dan één uitschuifbaar onderdeel
tegelijk uitschuiven.
WAARSCHUWING Als u verwisselbare opslagmedia wilt plaatsen, moet u de kast stabiliseren.
Voor de volgende producten maakt u gebruik van stabilisatiesteunen:
A4900A, A4901A, A4902A, A5134A, A5135A, A5136A, J1500A, J1501A en
J1502A.
U moet de stabilisatiesteunen zowel aan de voorkant als aan de achterkant
van de kast aanbrengen voordat u verwisselbare opslagmedia plaatst.
De volgende kasten moet u stabiliseren door onderin de kast ballast te
plaatsen: A1896A, A1897A, A1883A, A1884A, C2785A, C2786A en
C2787A.
Raadpleeg de informatie over ballast in de documentatie die u bij de kast
heeft ontvangen of bezoek www.eproducts.hp.com om te bepalen hoeveel
ballast is vereist.
Als u deze aanwijzingen niet opvolgt, kan dit leiden tot schade aan de
apparatuur of lichamelijk letsel.

English 9
Sikkerhedsforanstaltninger for skabe
ADVARSEL Skabene er tunge, selv når de er tomme. Vær forsigtig når De flytter skabe, hvad
enten der er installeret udstyr i skabet eller ej. Undgå at rulle skabe på ru eller
ujævne overflader eller skråninger der hælder mere end 10 grader. Der skal mindst
to personer til at aflæsse skabe fra pallen og til at flytte skabe.
ADVARSEL Udtræksdele må ikke være trukket ud, når skabet står på forsendelsespallen. Skabet
skal først læsses af pallen og anti-tip fødderne skal være installeret både forpå og
bagpå, før udtræksdelene må trækkes ud.
ADVARSEL Efter installation skal både de forreste og bageste anti-tip fødder blive siddende for
at opretholde stabiliteten. Der må kun trækkes en udtræksdel ud ad gangen.
ADVARSEL Ved enhver brug af udtræksdele skal der monteres anti-tip indretninger for skabet.
For følgende skabstyper anvendes der som anti-tip indretning et par anti-tip fødder:
A4900A, A4901A, A4902A, A5134A, A5135A, A5136A, J1500A, J1501A og J1502A.
Anti-tip fødderne skal monteres både på for- og bagsiden, før der isættes
udtræksdele.
For følgende skabe anvendes der som anti-tip indretning en ballast i bunden af
skabet: A1896A, A1897A, A1883A, A1884A, C2785A, C2786A og C2787A.
For beslutningen om, hvorvidt der er brug for ballast, henvises til
ballasttegningerne i papirerne, der følger med skabet, samt tit
www.eproducts.hp.com
Hvis ovenstående anvisninger ikke følges, kan det medføre materiel skade eller
kvæstelse.

10 English
Sikkerhetsforanstaltninger for skapene
ADVARSEL Skapene er tunge, selv når de er tomme. Vær forsiktig når du flytter skap, uansett
om de er tomme eller inneholder utstyr. Ikke rull skap på ru eller ujevne overflater
eller i skråninger som heller mer enn 10 grader. Det trengs minst to personer til
lessing av skap fra pallen og til flytting av skap.
ADVARSEL Produkter som kan gli inn og ut av skapet bør ikke være trukket ut når skapet er på
transportpallen. Skabet må lesses av pallen og anti-tippe-føtter må være påmontert
både foran og bak før et produkt som kan gli inn og ut av skapet, trekkes ut.
ADVARSEL Etter montering skal anti-tippe-føttene både foran og bak fortsatt være på for å
opprettholde stabilitet. Produkter som kan gli inn og ut av skapet, må kun trekkes
ut ett og ett om gangen.
ADVARSEL Bruk av produkter som kan gli inn og ut, krever at det installeres en
anti-tippe-enhet for skap.
Anti-tippe-enheten for følgende skapprodukter er et par anti-tippe-føtter: A4900A,
A4901A, A4902A, A5134A, A5135A, A5136A, J1500A, J1501A og J1502A.
Installer både fremre og bakre anti-tippe-fot på skapet før du installerer produkter
som kan gli inn og ut.
Anti-tippe-enheten for følgende skap er installering av ballast nederst i skapet:
A1896A, A1897A, A1883A, A1884A, C2785A, C2786A og C2787A.
Når du skal bestemme kravene til ballast, kan du se i ballastbeskrivelsen i
dokumentasjonen som fulgte med skapet, eller gå til www.eproducts.hp.com
Hvis disse forholdsreglene ikke blir fulgt, kan det føre til skade på utstyr eller
personer.

English 11
Laitekaappia koskeva turvavaroitus
VAROITUS Kaapit ovat tyhjinäkin painavia. Ole varovainen siirtäessäsi kaappia siitä
riippumatta, onko siihen asennettu laitteistoa. Älä rullaa kaappeja karkeilla tai
epätasaisilla pinnoilla tai jos pinnan kaltevuus ylittää 10 astetta. Kaappien
ottamiseen alas lastausalustalta ja niiden siirtämiseen tarvitaan ainakin kaksi
henkilöä.
VAROITUS Liukuvia osia ei pidä vetää ulos kaapista laitteen ollessa lastausalustalla. Kaappi
täytyy ottaa alas alustalta, ja sekä etummaisen että takimmaisen kallistustuen
täytyy olla asennettu ennen liukuvien osien vetämistä ulos.
VAROITUS Kun kallistustuet on asennettu, ne täytyy jättää paikoilleen sekä edessä että takana,
jotta kaappi pysyisi vakaasti paikoillaan. Vain yksi liukuosa saa olla ulkona
kerrallaan.
VAROITUS Liukuviksi asennettavien tuotteiden käyttö vaatii laitekaapin kaatumisen estävän
laitteen asentamista.
Kaatumisen estävä laite laitekaapeille A4900A, A4901A, A4902A, A5134A, A5135A,
A5136A, J1500A, J1501A ja J1502A on pari kaatumisen estäviä jalkoja.
Asenna sekä etu- että takajalka laitekaappiin ennen liukuviksi asennettavien
tuotteiden asentamista.
Kaatumisen estävänä laitteena laitekaapeille A1896A, A1897A, A1883A, A1884A,
C2785A, C2786A ja C2787A toimii painolastin asentaminen laitekaapin pohjalle.
Sopivan painolastin määrittämiseksi tutustu tuotteen mukana tulleisiin ohjeisiin
(ballast worksheets) tai käy www-sivuilla osoitteessa http://www.eproducts.hp.com
Näiden ohjeiden noudattamatta jättäminen voi johtaa laitteiston vaurioitumiseen tai
ihmisten loukkaantumiseen.

12 English

English 13
Declaration of Conformity
DECLARATION OF CONFORMITY
according to ISO/IEC Guide 22 and EN 45014
Manufacturer's Name: Hewlett-Packard Company
Internet & Applications Systems Division
Manufacturer's Address: 8000 Foothills Blvd.
Roseville, CA 95747
USA
declares, that the product
Product Name: Computer System
Model Number(s): RSVL-0105-A-xx (where -xx is an optional suffix and x
is any letter or blank)
Product Options: All
conforms to the following Product Specifications:
Safety: IEC 60950:1991+A1+A2 +A3 +A4 /
EN 60950: 1992+A1+A2 +A3 +A4 +A11
IEC 60825-1:1993 +A1 / EN 60825-1:1994+A11, Class 1
GB 4943-1995
EMC: CISPR 22:1997 / EN 55022:1998 Class A 1)
CISPR 24:1997 / EN 55024:1998
IEC 61000-3-2:1995 / EN 61000-3-2:1995 +A14
IEC 61000-3-3:1994 / EN 61000-3-3:1995
GB 9254-1988
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive
73/23/EEC and the EMC Directive 89/336/EEC and carries the CE marking
accordingly.
1) The product was tested in a typical configuration with Hewlett-Packard computer
peripherals.
2) DC versions of the product were tested in a typical configuration with a Hewlett-
Packard 6813A AC/DC power source.
Roseville, 6/1/01
European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH,
Department HQ-TRE, Herrenberger Straße 130, D-71034 Böblingen (FAX: + 49-7031-14-3143)

14 English
FCC Statement (USA Only)
The United States Federal Communications Commission has specified that the following notice be
brought to the attention of users of this product:
NOTE This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Hewlett-Packard's system verification tests were conducted with HP-supported peripheral devices and
HP shielded cables, such as those you receive with your computer. Changes or modifications not
expressly approved by Hewlett-Packard could void the user's authority to operate the equipment. Cables
used with this device must be properly shielded to comply with the requirements of the FCC.
Canada RFI Statement
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
European Union RFI Statement
This is a Class A product. In a domestic environment, this product may cause radio interference in which
case the user may be required to take adequate measures.
Acoustics (Germany)
Acoustic noise level per ISO 9296 (25°C):
LpAm<60dB (operators position)
Australian C-Tick Label
Laser Safety
This product contains a laser internal to the Optical Link Module (OLM) for connection to the Fibre
communications port.
In the USA, the OLM is certified as a Class 1 laser product conforming to the requirements contained in
the Department of Health and Human Services (DHHS) regulation 21 CFR, Subchapter J. The
certification is indicated by a label on the plastic OLM housing.
Outside the USA, the OLM is certified as a Class 1 laser product conforming to the requirements
contained in IEC 825-1:1993 and EN 60825-1:1994, including Amendment 11:1996.