HP Invent Q1573 Series Assembly instructions

EL-MF877-00 Page 1
Template Revision A
Product End-of-Life Disassembly Instructions
Product Category: Data Storage Devices
Marketing Name / Model
[List multiple models if applicable.]
DAT160 internal SCSI / Q1573X, Q1576X, EB630X, EB632X & EB633X (where X = any alphanumeric combination)
DAT160 internal USB / Q1580X, Q1583X, EB635X, EB637X & EB638X (where X = any alphanumeric combination)
DAT160 internal SAS / Q1587X, Q1590X, EB640X, EB642X & EB643X (where X = any alphanumeric combination)
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions
for the disassembly of HP products to remove components and materials requiring selective treatment, as defined by EU
directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).
1.0 Items Requiring Selective Treatment
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product whichrequire selective treatment in the right column, as
applicable.
Item Description Notes
Quantity
of items
included
in product
Printed Circuit Boards (PCB) or Printed Circuit
Assemblies (PCA) With a surface greater than 10 sq cm 4
BatteriesAll types including standard alkaline and lithium coin
or button style batteries 0
Mercury-containing components For example, mercury in lamps, display backlights,
scanner lamps, switches, batteries 0
Liquid Crystal Displays (LCD) with a surface greater
than 100 sq cm Includes background illuminated displays with gas discharge lamps 0
Cathode Ray Tubes (CRT) 0
Capacitors / condensers (Containing PCB/PCT) 0
Electrolytic Capacitors / Condensers measuring
greater than 2.5 cm in diameter or height 0
External electrical cables and cords 0
Gas Discharge Lamps 0
Plastics containing Brominated Flame Retardants 0
Components and parts containing toner and ink,
including liquids, semi-liquids (gel/paste) and toner Include the cartridges, print heads, tubes, vent chambers, and service stations. 0
Components and waste containing asbestos 0
Components, parts and materials containing
refractory ceramic fibers 0
Components, parts and materials containing
radioactive substances 0

EL-MF877-00 Page 2
Template Revision A
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where components
and materials requiring selective treatment can be removed.
Tool Description Tool Size (if
applicable)
Crosshead screwdriver
Torx screwdriver T-10
Nippers N/A
3.0 Product Disassembly Process
3.1 List the basic steps that should typically be followed to remove components and materials requiring selective treatment:
3.1.1. Remove metal wing brackets (5.25” product only, 4 xT-10 screws) and the front panel.
3.1.2. Remove side panels by unscrewing 14 x crosshead (CH) screws from each side. See image 1. Remove the lid by
removing 1 x CH screw at the rear of the mechanism (See image 2) and 2 x CH screws at the front top of the mechanism.
See image 3.
3.1.3. Remove the base and the cartridge assembly (see image 4) and remove 1 x CH screw from the BOM-ASSY. (see
image 5)
3.1.4. Unlock and release FFCs and FPCs from the PCA (see image 6).
3.1.5. Unscrew 5 x CH screws from the base of the PCA and remove main PCA (> 10 sq cm). See images 7&8.
3.1.6. Remove REC-SW-PCA (> 10 square cm’s). See image 9.
3.1.7. Remove ARM-HOUSING, HC-W-ASSY, ARM-P8-SUB-ASSY, the GUIDE-V-PR, and PR-ASSY from drive to access
the MODE-DRIVE-ASSY. (see images10 and 11)
1.1.8. Unlock FFC connector and release FFC-9pin. Unscrew 6 x CH screwsand remove MODE-DRIVE-ASSY. See
image 12.
1.1.9. Cut out the 4 x wires from the mode-drive-assembly and unscrew the 4 x CH screws to release the PWB-MODE-A.
PWB-MODE-A is > 10 square cm’s.See image 13.
1.1.10Remove 5 x CH screws to release the P-SUB-CHASSIS, 7 x CH screws to remove the REEL-MOTOR and PWB-
MODE-B-ASSY and 3 x CH screws to release the DRUM-ASSY. PWD-MODE-B-ASSY is > 10 square cm’s. See image
14.
3.2 Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items
contained inthe product that require selective treatment (with descriptions and arrows identifying locations).

EL-MF877-00 Page 3
Template Revision A
1) 2) 3)
Remove 14 screws per side. Remove M1.7 screw a rear side. Remove 2 xM1.7 screws at front top.
4) 5) 6)
Remove base and cartridge housing Remove 1 x CH screw from BOM
ASSY Unlock and release FFCs and FPCs fromthe PCA.
7) 8) 9)
Remove 5 x CH screws to remove
the PCA Remove main PCA (> 10 square cm’s). Unscrew 3 x CH screws to remove the REC-SW-PCA-assembly (> 10
square cm’s)
10) 11) 12)
13)
Clip 4 wires and remove 3 screws.
PWB-MODE-A is > 10 square cm’s
LID
BASE
CARTRIDGE
-
HOUSING
BOM
-
ASSY
PCA
ARM
-
HOUSING
-
ASSY
HC
-
W
-
ASSY
ARM
-
P8
-
SUB
-
ASSY
PR
-
ASSY
GUIDE
-
V
-
PR
FFC
-
9PIN
Connector
REC
-
SW
-
PWB
P
WB
-
MODE
-
A

EL-MF877-00 Page 4
Template Revision A
14)
Remove PWA-MODE-B-ASSY > 10 square cm’s
REEL
-
MOTOR
-
ASSY
PWA
-
MODE
-
B
-
ASSY
DRUM
-
ASSY