HPM Sika LSP0112WBL User manual

Instruction Manual
Sika LED Floodlights
Cat. No. LSP0112WBL, LSP0125WBL
These products must be installed by a licensed electrician.
LSP0112WBL LSP0125WBL
Where to mount your floodlight:
1. Installation is to be made in dry weather conditions.
2. Choose a mounting position that is in a sheltered location (e.g under the eaves of the house). A mounting height of greater than 2m is recommended.
3. Do not operate in close proximity to combustible materials or substances affected by heating or drying. Keep a minimum distance of 0.5m from
adjacent objects.
Installation:
Installing a wall switch adjacent to the power source is recommended.
1. Remove the mounting bracket from the back of the fitting (figure A & B).
2. Loosen the cord anchorage on the mounting bracket by loosening the two screws (figure C).
3. Choose rubber-sheathed 3-core circular cord, H05RN-F 3G 1mm2 (not supplied) for the mains wiring.
4. Insert mains wiring through the grommet on the mounting bracket (figure D).
5. Connect the mains wiring to the terminal block as marked on the mounting bracket. Ensure that the wires are secure and no bare wires are exposed
(figure E).
6. Use the mounting bracket as a template to mark the screw positions onto the wall (figure F).
7. Install the mounting bracket onto the wall. Ensure the method of fixing can support up to a 10kg weight.
8. Place the mains wiring in the cord anchorage system and secure by tightening the screws. Ensure it clamps onto the cord sheath (figure G).
9. Install the fitting back onto the mounting bracket and tighten the screws (figure H & I).
10. Adjust the head of the fitting to the desired position.
11. DO NOT MEGGER TEST.
A B C D
E F G H I

Disclaimers
1. This product must be installed and used as per these instructions.
2. An IP rating of IP44 is generally considered suitable for external
walls with supplementary protection such as overhanging eaves.
3. The IP rating of this product is only valid when installed on a flat
and non-porous surface. Additional sealing may be required for
irregular surfaces.
4. The fixing screws on this product should be tightened to a
maximum torque of 0.8Nm. Over tightening may damage the product.
5. This product contains no serviceable parts and no attempt should
be made to repair this product. If the product is faulty it should
be discarded.
6. This product is not suitable for installation in hazardous and/or
corrosive areas.
7. Electrical installations periodically receive transient over voltages.
This product has been designed to minimise the effect of such
voltages on connected equipment. It may not give full protection
for extreme over- voltage transients such as those resulting from
a close lighting strike.
8. This product utilises intellectual property in the form of registered
designs, trademarks, and/or patents. Such intellectual property
remains the property of HPM Legrand in all cases.
9. HPM Legrand reserves the right to modify the specification of this
product at any time.
10. This product has been designed to operate in ambient temperatures:
-10°C to 45°C.
11. The material in this product may vary in colour from batch to batch.
Colour matching from one batch to another cannot be guaranteed.
Specifications
Cat no. LSP0112WBL LSP0125WBL
Supply voltage 230-240V a.c. 50Hz
Input power 14W 29W
Power output 12W 25W
Lumens output 1070lm 2200lm
Colour temperature Cool white 4000K nominal
Mounting height > 2m (recommended)
Protection class Class 1
Weatherproof rating IP44
Size (mm) 170 x 120 x 180 mm 170 x 240 x 180 mm
Weight
(excl packaging) 0.6kg 1kg
Power cord
requirement H05RN-F 3G 1mm2
A B C D
E F G H I
03/2017 HPML0573/BLE08110AGB
Warranty
HPM Legrand warrants this product for a period of 5 years from the
date of purchase when used in accordance with these instructions
and considering the disclaimers listed herein.
These goods come with guarantees that cannot be excluded under
the Australian and New Zealand Consumer Laws. You are entitled to
a replacement or a refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired if the goods fail to be acceptable
quality and the failure does not amount to a major failure.
See the Warranty card enclosed with this product for further details.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
wLegrand Australia
1300 369 777
www.hpm.com.au
HPM Legrand New Zealand
0800 476 009
www.hpm.co.nz
ABN: 31 000 102 661