hq telecom HQ-TS-350 User manual

Step-by Step Instructions for the Installation and Programming for the
Outgoing Phone Blocker with Allow & Disallow Memory
UPDATES & SAFETY INSTRUCTIONS:
Please refer to hqtelecom.com for latest updates and safety instructions about this outgoing
phone blocker (also http://hqtelecom.com/PhoneBlocker-wAllow-and-Disallow-Memory-
Manual.pdf).
INSTALLATION: Please connect the Call Blocker as shown in the diagram below:
PROGRAMING:
After installing it, lift off the handset connected to the PHONE port of the device and use the
dial-pad to program your device as shown below.
To DISALLOW numbers,
area codes, and prefixes:
#0* (wait to hear beep)
05 (beep)
Enter Disallow-number
## (2 beeps)
hangup
Examples:
- Block all 10-digit calls starting with area code 305-xxx-xxxx:
#0* (beep) 05 (beep) 305******* ## (beep, beep)
Note: You need to enter * 7 times as a wild card. If you are
required to dial 1+area code + number, you will need to enter
1305******* ##.
- Block all 10-digit calls starting with prefix 305-558-xxxx:
#0* (beep) 05 (beep) 305558**** ## (beep, beep)
Note: You need to enter * 4 times as a wild card for each digit.
1305558**** ##.
IMPORTANT: PLEASE IGNORE ALL ERROR MESSAGES YOU
HEAR FROM YOUR PHONE COMPANY WHILE PROGRAMMING
THIS DEVICE.
To ALLOW numbers,
area codes, and prefixes.
#0* (beep)
08 (beep)
Enter Allow-number
## (2 beeps) hang-up
By default all numbers are allowed. So, if you want to
program this device to only ALLOW certain numbers (prefixes
or area codes), you first need to DISALLOW it (using function
code 05 as shown above).
For example, you can DISALLOW all calls starting with 305
(using the 05 function code as shown above). Then use

function 08 to ALLOW calls to prefix within 305-558-xxxx or
specific numbers within area code 305 e.g. 305-558-5577.
Change Passcode:
#0* (beep)
70 (beep)
New_Pass code
## (beep, beep)
hangup
The default programming pass-code is #0* (pound - zero -
star).The programming pass code can be any combination of
digits (0-9), # or *.
Example:
#0* (beep) 70 (beep) 123 ## (beep, beep) (Changes pass code
to 123)
Restore factory defaults
#0* (beep)
88 (beep)
## (beep, beep)
hangup
Use these instructions in case you need to reset the lists of
allowed & disallowed numbers you have entered.
Important: If you changed the programming pass code and
cannot remember it, or the memory has been corrupted and
cannot enter programming mode, refer to Hardware reset
instructions (below).
HARDWARE RESET INSTRUCTIONS:
If you lose or forget your own security pass code (default as 54321*), you will need to follow
the instructions below:
Preparation: You will need to open the black enclosure with a thin flat-headed screw driver.
You will also need a piece of metal to make contact with the two terminals as described
below.
Circuit Diagrams
Revision A & B
Step 1 - Short the two reset pads together
with something metallic.
Step 2 - While shorting the two pads take the
telephone handset off hook and wait one
second, then remove the short.
Step 3
You should hear two beeps through the telephone
handset confirming that the unit has been defaulted.
Revision C
Step 1 - Press and hold the factory reset button.
Step 2 - While holding the button down take the
telephone handset off hook and wait one second,
then release the button.
Step 3 - You should hear two beeps through the
telephone handset confirming that the unit has been
defaulted.