HS LN42 User manual

Operation Manual of Mini Dome Camera
Content
Precaution。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
2
Chapter One Product Overview
1．Integrated multi-protocol decoder。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
3
2．Integrated all dimension return PTZ。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
3
3．Function description。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
3
Chapter Two Fast Operation Guide of Dome Device
1． Wiring。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
5
2．Setting protocol and baud rate。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
6
3． Setting dome device address。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
6
4．Install camera。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
6
5．Connect the power of dome device。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
7
6．Controller setting。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
7
7．Start testing。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
7
8．Complete the test。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
8
1

Operation Manual of Mini Dome Camera
Chapter Three Function Operation
1．Setting of preset direction position。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
9
2．Setting of the Pan scan between two points。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
9
3．Operation instruction about the tour scan。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
10
4．Setting of return point。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
10
5．Intelligent three-dimension tour scan setting。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
10
6．Camera menu operation 。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
11
Chapter Four Trouble Shooting。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
13
Chapter Five Major Technical Parameter。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
14
2

Operation Manual of Mini Dome Camera
Chapter One Product Overview
3
Precautions:
1.Non-techinician is forbidden to operate this dome device
before reading this manual carefully.
2.Cut the power supply off before operating the dome
device to avoid damage caused by mal-operation.
3.Interior of the Dome device are precision optical and
electrical instruments. Heavy pressure, shock and other
incorrect operations should be prevented. Otherwise, may
cause damage on product.
4. Please do not remove and disassemble any internal parts
of Dome video camera by self in order to avoid normal
usage being impacted. There is no part inside the device,
which can be repaired by users themselves.
5. All the wiring of the dome device should be conducted
strictly according to the wiring instruction. When
necessary, thunder
-
proof, surge
-
proof and other protecting

Operation Manual of Mini Dome Camera
This dome device is a hi-tech monitoring product integrating high-resolution color camera
and multi-function decoder, which minimizes the wiring and installation process and enhances
the reliability of the system as well as facilitates installation and maintenance. It has the
advantages of elegant appearance, flexibility, simple operation and high compatibility.
1. Integrated multi-protocol decoder
a. The build-in communication decoder integrates the communication protocol of Pelco_D
or P with baud rate from 2400bps to 19200bps (can be realized by setting the position of
dip switch inside the dome device).
b. RS485 communication control; the range of dome address is 0～255.
2. Integrated swivel and tilt movement
A. Pan rotation is 360º endless; Tilt movement is 0～90º，by using the key boards speed can
be adjustable from 0.1～60°/s.
b. The low speed running is stable with ultra-low noise and without image shake.
c. by pushing down the Joystick till the point of 90º the camera will auto lift up 10 degree.
Monitoring all directions with ±0.2º precision.
3. Function description
a. 64 -preset positions: All data of preset position will be saved on time and will not be
lost when power is suddenly off.
b. Free selection of Pan scan direction: support the Pan scan with the shortest distance
between two points (scan speed: 0.1～30 degree/second, variable speed selection
available). Besides, tilt movement can be achieved manually at the same time.
c. Two groups of programmable tour: It has the functions of tour setting and call out, as
well as saving the directional used programmed tour. Each group of tour contains 16
4

Operation Manual of Mini Dome Camera
preset positions, the running speed and dwell time of which can be set and the data will
not be lost when the power is off. (This function depends on the function and operation
mode of controller such as keyboard adopted or DVR card.)
d. Power off memory: If the power is suddenly off when the dome device is in operation
pan scan or tour, the dome device will resume the Pan scan or tour when the power is
on again.
e. Home position function The time of Home position can be set. If the dome device does
not receive and control within preset time duration, the dome will return to the preset
position of number “1”.( Home position)
f. Intelligent three-dimension tour scan: When monitoring manually by means of
joystick, the dome unit automatically continues the rotation and tilt operation.
5

Operation Manual of Mini Dome Camera
Chapter Two Fast Operation Guide of Dome Device
1>. Wiring (Please do not turn the power on).
Please carry out the wiring and installation according to below illustration.
6

Operation Manual of Mini Dome Camera
2>.The communication protocol of dome device is PELCO-D
2400BPS/PELCO-P 4800BPS
3>. Setting the device address (Turn the power off when setting, and
restart the device after revision).
The figure shows: Address of the dome device: No. 1
(Please refer to detailed parameter in next chapter)
This dipswitch located on PCB in the dome device
7
Set address for dome
Setting method: The sum of switch numbers when it is
at ON position is the address of dome device.
Calculation example of dome device address:
1
2
4
816
32
64
128
Matching numbers
Matching
numbers numbernum be
字
2416
（2+4+16=22 ）the address is 22.
On/off switch and
matching numbers
Matching
Matching Matching

Operation Manual of Mini Dome Camera
4>. Install camera. (Please refer to camera installation for details).
Attention: 1.Do not connect the camera and dome device with FFC in a
wrong way.
2. The holes are for different cameras. Please adjust according to
the practical overall dimensions and ensure the fastness when
installation is completed.
5>. Connect the power of dome device.
At this moment, the self-test (rotation) of dome device and self-test
(there will be image on the monitor) of camera can be seen.
6>. Set the protocol, baud rate and address of the keyboard
controller identical with those of dome device. (Please refer to
keyboard controller instruction manual).
7>. Start testing.
When the entire above are ready, the testing to dome device can be
started.
The directions (up, down, left and right) of the
dome device can be controlled by using the
Keyboard controller, as indicated in the figure.
Note: the working of dome device is normal
joy stick
8
up down
n
left
right

Operation Manual of Mini Dome Camera
.8>. Complete the test. (Summary).
1. If the performance of item 7 is normal, it indicates the system is
normal. Please do not change the wiring and various setting to
avoid fault and unnecessary damage and loss.
2. If the performance of item 7 is irregular, or only one item works
normally, please check the wiring (item 1 and 4) and setting (item
2, 3 and 6) carefully.
Remarks:
1. Please read this manual and test guide carefully before using this product to get to understand
each electric parameter.
2. Please refer to the attached operation manual for more functions of the dome device.
3. Non-qualified technicians are forbidden to conduct and test, debugging and operation toward
this product.
9

Operation Manual of Mini Dome Camera
Chapter Three Function Operation
I. The setting of preset direction position (note: the operation mode differs for different
dome device controller, Please read the manual of the controller before operation)
Preset direction position: No. 1～50 and 64 ~77（total 64 presetting positions）
Function short-cut preset position: No.51～63, No.78～101.
Save preset position (Example):
Method One: First input＂PRESET＂, and then input the number of
preset position and press ＂ENTER ＂at the end ．
(PRESET + Preset position number + ENTER)
Method Two: First input preset position number, and then press＂SHOT
＂, and press＂ON＂at the end.
(Preset position number + SHOT + ON)
Call preset position (Example):
Method One: First input ＂CALL ＂, and then input preset position
number, and press ＂ENTER ＂at at the end ．(CALL +
Preset position number + ENTER)
Method Two: First input preset position number, and then press ＂SHOT
＂, and press＂ACK＂at the end.
(Preset position number + SHOT + ACK)
Clear preset position (Example):
Method One: First input＂PRESET＂, and then input the preset position
number and press ＂OFF ＂at the end.(PRESET + Preset
position number + OFF)
Method Two: First input the preset position number, and then press ＂
SHOT＂, and press＂OFF＂at the end.
(Preset position number + SHOT + OFF)
II. Setting of the Pan scan between two points (Example:Method one)
1）The dome device conduct auto Pan Scan between two points.
10

Operation Manual of Mini Dome Camera
2）Users can set the starting point by pressing “PRESET+52+ENTER” and set the
ending point by pressing “PRESET+53+ENTER”.
3）The setting of Pan scan speed: user only need to maintain a certain manual scan
speed for more than 3 seconds and press“CALL+51+ENTER”to save this speed as
Pan scan speed, press “CALL+52+ENTER” to start Pan scan.
4）The dwell time of “starting point” and “ending point” of Pan scan is 2 seconds.
5）Stop it by operate “Pan”or “Tilt”.(move the joystick of the controller).
III. Operation instruction about the tour scan movement (Example:Method one)
1. Auto point by point scan from preset point number 1 to number 16, if a certain
point is not set or cleared, that point will not be scan when “tour scan” is in
progress.
2. The dwell time of preset point in tour is 4 seconds.
3. The defaulted tour function can be executed by inputting
“PRESET+51+ENTER”.
4. Please refer to the operation manual of keyboard control for the operation of
other six tour tracks.
5. Stop it by operate “Pan”or “Tilt”.(move the joystick of the controller)
IV. Home position（This means the time duration for the dome device to return to the
No. 1 direction preset position when no-man control occurs）(Example:Method one)
1. Start this function by pressing “CALL+100+ENTER”.
2. The time of returning to preset direction position number 1 can be set to 1
minute / 2 minutes / 4 minutes / 8 minutes / 10 minutes by pressing
“CALL+95+ENTER” / “CALL+96+ENTER” / “CALL+97+ENTER” /
“CALL+98+ENTER” / “CALL+99+ENTER”
3. Disable this function by pressing “PRESET+100+ENTER”
V. Intelligent three-dimension tour scan setting (Example:Method one)
When the user is monitoring with manual Pan scan, he only needs to maintain the scan
speed for more than 3 seconds to continue the scan speed and direction monitoring,
and then press “CALL+101+ENTER” to auto continue the manual Pan scan action.
11

Operation Manual of Mini Dome Camera
At the same time, the tilt movement can be changed.
VI Camera menu operation: Invoke(Call) No.57 preset position entry.
1) Input “Tele” or ”Wide” command for cursor movement and option selection
2) Input iris “Open”/“Close” or focus “Near”/“Far” for enter the option or changing
the setting value
Function Table:
Number
of preset
position
Control Object Definition of Keyboard Operation
Call preset position Save preset position
51 Pan-tilt Compensation
Control Save line-scanning speed Enable system default cruisetrack
52 Enable line scanning Set starting point of
scanning
53 System hold Set ending point of
scanning
55 Background Light
Compensation * On Off
58 Digital Zoom * On Off
59 Focus Auto Manual
60 Iris Auto Manual
100 Home position Enable Disable
95 Dwell time setting for
the Home position
function
1 minute
96 2 minutes
97 4 minutes
98 8 minutes
99 10 minutes
101 Intelligent manually
horizontal continuous
scanning
ON
12

Operation Manual of Mini Dome Camera
Chapter Four Trouble Shooting
Problems Possible Causes Solutions
After power on, no motion and
no image. Power supply damage or low power Replace
Wrong power cable wiring Correct
Engineering wiring fault Detect
Abnormal self detect, normal
image with motor sound Mechanical fault Repair
Tilted camera Reposition in the right way
Lower power supply Replace with appropriate power
supply and optimally place the power
supply near the dome device
Normal self detect, but no image Wrong video wiring Correct
Bad contact of video cable Detect
Camera damage Replace
Self detect success, but out of
control Wrong wiring of control signal cable Correct
Unmatched dome device address Select again
Unmatched protocol Adjust protocol to match the control
system and power on again
Unstable image Bad contact of video cable Detect
Low power supply Replace
Dome device out of control Abnormal self detect Power on again
Bad contact of control cable Detect
Wrong with main device
operation Power on the main device again
Overload or too long
communication distance 1．Confirm terminal impedance
2．Raise the distributor
Vague image Focusing is not at the best
position Open the dome and readjust
13