Interlogix UltraView User manual

UltraView IP PTZ 36X
Camera Quick Start
Guide
EN
UltraView IP PTZ 36X Camera Quick Start Guide
DE
UltraView IP PTZ 36X-Kamera - Kurzanleitung
ES
Guía de inicio rápido de la cámara UltraView IP PTZ 36X
FR
Guide de démarrage rapide de la caméra UltraView IP PTZ
36X
IT
Guida di avvio rapido telecamera UltraView IP PTZ 36X
NL
UltraView IP PTZ 36X‑camera Beknopte handleiding
PL
Skrócona instrukcja obsługi kamery UltraView IP PTZ 36X
PT
Guia Rápido da Câmara UltraView IP PTZ 36X
RU
Краткое руководство по началу работы скамерой
UltraView
IP PTZ 36X
TR
UltraView IP PTZ 36X Kamera Hızlı Başlangıç Kılavuzu
P/N 1071694D-Multilingual • ISS 07DEC12

Copyright © 2012 UTC Fire & Security Americas
Corporation, Inc.
Interlogix is part of UTC Climate Controls &
Security, a unit of United Technologies
Corporation. All rights reserved.
Contact
information www.interlogix.com
www.utcfssecurityproducts.eu

UltraView IP PTZ 36X Camera 1 EN
EN
Introduction
This pocket guide provides basic information on setting up and using
the UltraView IP PTZ 36X camera. Detailed information on the
cameras can be found in the user manual.
Before you begin
Unpack everything. Check the items for damage, and verify that all
items are included. The camera is shipped with the following items:
Dome camera
User manual
Quick Start Guide
Installation environment
When installing your camera, consider these factors:
• Place the camera in a secure location.
• Ensure that the camera is in a well-ventilated area.
• Do not expose the camera to rain or moisture.
Camera description
Figure 1: Overview of the dome camera (pendant-mount shown)
1. Ethernet RJ45 connector.
Connect to the network
devices.
2. Video output.
Connect the BNC connector to
a CCTV monitor.
3. Power supply cord.
Connect +24 VAC power
supply.
4. Housing.
5. PTZ module.
6. Bubble.

EN 2 UltraView IP PTZ 36X Camera
Installing a camera
1. Prepare the mounting surface and install the camera bracket.
2. Unscrew the bubble from the camera and remove the protective
tape from the PTZ module.
3. Press the two tabs on either side of the PTZ module and remove it
from the camera housing. Ensure the module cables still exit from
the cable entry hole in the top of the housing.
Note: If alarm and audio input/output relays are to be used,
connect them to the PCB of the module and route their cables
through the cable entry hole on tom of the housing. See the user
manual for further information on the alarm connections.
4. Install the housing.
Pendant-mount camera:
Attach the camera housing to the bracket using the screws
enclosed with the bracket.
Flush-mount camera:
Adjust the height of the two housing tabs by turning the screw on
which they are attached. The distance (h) of the tabs from the
housing ring must be greater than the thickness of the ceiling.
Housing tab
Screw
Make sure the housing tab is closed and then PUSH the housing
into the pass-through hole. Hold the housing and fix it by screwing
the housing tabs down to the mounting surface
5. Insert the PTZ module into the housing:

UltraView IP PTZ 36X Camera 3 EN
Position the tabs on the PTZ module by aligning the arrow label on
the module with those on the housing (see below). The module
should firmly snap into position. If using a SDHC card, insert it into
the module before inserting the module into the housing.
6. Re-attach the bubble by screwing it to the housing.
7. Pendant-mount camera only: Route the PTZ module cables
through the bracket.
Flush mount camera only: Install the trim ring. Align the trim ring
to the housing, and insert the fix-pins to the holes. Then rotate the
ring clockwise.
8. Connect the cables (see Figure 1).
Warning: After installation, the PTZ module will perform a PTZ
self-test and initializes with the power on. DO NOT touch and
move the camera while it is self-testing and initializing.
9. Configure the dome camera to suit its location.
Accessing the camera over the internet
Use the Web browser to access and control the camera over the
internet.
Note: Any changes made to the camera’s configuration only apply to
this camera.
Change the administrator password once the set up is complete. Only
authorized users should be able to modify camera settings.
To access the camera online:
1. In the Web browser enter the camera’s IP address (default is
192.168.1.70). The Login dialog box appears.
2. Enter your user name and password as well as the port to be used.
Default user name: admin
Default password: 1234

EN 4 UltraView IP PTZ 36X Camera
Default port: 8000
Click OK. The Web browser screen appears in live mode. The live
screen is initially blank.
3. Click the Start Live View button on the top of the screen for
the live mode images to appear on-screen.
4. Right-click Camera 01 to open the pop-up box and select the
desired stream: Main, Sub or Open sound.
Web browser interface
1.
Menu toolbar select live view,
playback, search event logs
and configure camera over the
internet.
2.
Viewer pane.
3.
Current user
4.
Exit the system.
5.
PTZ button.
6. PTZ control panel
7. Preset selection
8. Full screen
9.
Start live view, record video and
take snapshots.
10. Start/stop bi-directional audio.
11. Turn the audio function on or
off.

UltraView IP PTZ 36X Camera 5 EN
Configuring the camera over the internet
In the camera browser screen, click the Configuration button in the
menu toolbar to access the configuration screens. See Table 1 below
for the list of configuration parameters.
The configuration pane displays the configuration tree with 10
configuration parameter folders. The configuration pane is always
visible. Each folder has a list of subfolders that display the different
configuration screens.
Figure 2: Configuration screen
Configuration pane
Table 1: Overview of the configuration parameter folders
Configuration fo
lder Description
Local configuration
Manages the network type, display mode and
local storage paths.
Basic information
Defines the device name and RS-485 bus ID
as used by the network. It also displays the
MAC address, device type, device SN, current
firmware version, U-Boot version and current
server time
DST time
Defines when daylight saving time starts and
ends.

EN 6 UltraView IP PTZ 36X Camera
Configuration fo
lder Description
Channel parameters
Defines the OSD properties of camera
information, recording schedule, recording
settings for alarm events, alarm response and
overlay text.
Network parameters
Defines the network parameters required to
access the camera over the internet.
Alarm parameters
Defines how the camera handles alarms such
as input type, notification of alarms, and
response schedules and duration.
Motion
Defines how the camera moves such as
presets, shadow tours, and privacy masks..
Deployment time
Defines the schedules during which events
can
be registered
User
management Defines who can use the camera, their
passwords and access privileges.
HDD management
Defines how to format the SDD card used in
the camera.
Remote
upgrade Defines how to upgrade the camera’s
firmware.
Default
Restores factory default settings.
Reboot device
Reboots the camera.
Specifications
Operating temperature Pendant housing: -10 to +50 °C
(-14 to +122 °F)
Flush housing: -30 to +65 °C (-22 to +149 °F)
Power supply 24 VAC +/- 4 VAC
Power consumption 30 W (heater on), 15 W (heater off)
Dimensions Pendant housing: Ø 220 × 299 mm
(Ø 8.66 ×10.27 in)
Flush housing : Ø 206 × 241 mm
(Ø 8.11 × 9.49 in.)
Environmental Pendant housing: IP66
Flush housing: IP54
Weight 5 kg (11 lb.)

UltraView IP PTZ 36X-Kamera 7 DE
DE
Einführung
Diese Kurzanleitung bietet die grundlegenden Informationen zur
Einrichtung und Verwendung der UltraView IP PTZ 36X camera
Detaillierte Informationen zu den Kameras entnehmen Sie bitte
dem Benutzerhandbuch.
Bevor Sie beginnen
Packen Sie alle Komponenten aus. Überprüfen Sie die einzelnen
Komponenten auf eventuelle Beschädigungen und achten Sie darauf,
dass alle Komponenten geliefert wurden. Die folgenden Teile sind im
Lieferumfang der Kamera enthalten:
Dome
Benutzerhandbuch
Schnellstartanleitung
Installationsumgebung
Beachten Sie beim Installieren der Kamera folgende Faktoren:
• Platzieren Sie die Kamera an einem sicheren Ort.
• Vergewissern Sie sich, dass sich die Kamera an einem gut
belüfteten Ort befindet.
• Setzen Sie die Kamera weder Regen noch Feuchtigkeit aus.

DE 8 UltraView IP PTZ 36X-Kamera
Kamerabeschreibung
Abbildung 3: Überblick über den Dome (Darstellung zeigt
abgehängte Montage)
1. Ethernet-RJ45-Anschluss.
Anschluss für Netzwerkgeräte.
2. Videoausgang.
Verbinden des BNC-
Anschlusses mit einem CCTV-
Monitor.
3. Netzkabel.
Anschluss an +24 VAC-
Stromquelle.
4. Gehäuse.
5. PTZ-Modul.
6. Kuppel.
Installieren der Kamera
1. Bereiten Sie die Montagefläche vor und installieren Sie die
Kamerahalterung.
2. Lösen Sie die Kuppel von der Kamera und entfernen Sie die
Schutzfolie vom PTZ-Modul.
3. Drücken Sie auf die Laschen an beiden Seiten des PTZ-Moduls
und entfernen Sie dieses vom Kameragehäuse. Achten Sie darauf,
dass die Modulkabel weiterhin durch die Kabeleinführungsöffnung
oben im Gehäuse geführt werden.
Hinweis: Bei Verwendung von Alarm- und Audio-Eingangs-/-
Ausgangsrelais schließen Sie diese an die Leiterplatine
des Moduls an. Führen Sie die Kabel durch die
Kabeleinführungsöffnung oben im Gehäuse. Weitere
Informationen zu Alarmanschlüssen finden Sie im
Benutzerhandbuch auf Seite.
4. Anbringen des Gehäuses.
Abgehängte Montage:
Befestigen Sie das Kameragehäuse mithilfe der mitgelieferten
Schrauben an der Halterung.
Bündige Montage:
Passen Sie die Höhe der beiden Laschen am Gehäuse durch
Drehen ihrer Befestigungsschraube an. Der Abstand (Höhe)