Honeywell HD4DX User manual

Document 800-00023 – Rev D – 05/07
User Guide
Day/Night DNS Fixed
Dome Camera
NTSC / PAL
HD4D HD4DX

2
Revisions
Issue Date Revisions
A 04/07 New document.
B 05/07 Increase line weight of illustrations.
C 05/07 Corrected specifications.
D 06/07 Changes:
Page 14, LL switch is on power supply board.
Page 18, corrected Day/Night mode explanation.
Page 24, corrected Vertical Phase Adjustment to 0 - 359°.

Document 800-00023 Rev D 3
05/07
Warnings
Installation and servicing should be performed only by qualified and experienced technicians
to conform to all local codes and to maintain your warranty.
WARNING! 12 VDC/24 VAC models require the use of CSA Certified/UL Listed
Class 2 power adapters to ensure compliance with electrical safety
standards.
Explanation of Graphical Symbols
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of
this product (applicable in the European Union and other European
countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws,
regulations, and procedures.
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
THE COVER. NO USER-SERVICEABLE
PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
THIS SYMBOL INDICATES
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES
THAT IMPORTANT OPERATING
AND MAINTENANCE
INSTRUCTIONS ACCOMPANY
THIS UNIT.
CAUTION

4
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits
for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Caution Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential protection requirements of the EMC directive 89/336/EEC and the Low Voltage
Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55013 for
emissions, EN 50130-4 for immunity, and EN 60065 for Electrical Equipment safety.

Document 800-00023 Rev D 5
05/07
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Unpack Everything. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting Cables Through the Housing Base . . . . . . . . . . . .8
Connecting Cables Through the Side Conduit . . . . . . . . . . . . .9
Electrical Box Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting the Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Line Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adjusting the Lens Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Camera Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
OSD Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SPECIAL Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Adding a Camera Title Display . . . . . . . . . . . . . . . . . . . . . . . 19
Sync Control Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Motion Detection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Privacy Mode Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Solving Common Technical Issues . . . . . . . . . . . . . . . . . . . . . . . . 22
Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Cable Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6
Introduction
The unobtrusive, low-profile design of the HD4D CCTV Camera is ideal for indoor and outdoor
installations in commercial and residential venues.
Before You Begin
Please read this guide carefully before you install the HD4D CCTV Camera.
Keep this guide for future reference.
Unpack Everything
Check that the items received match those listed on the order form and packing slip. The
HD4D packing box should include, in addition to this User Guide:
• One fully-assembled HD4D camera, including factory-installed pigtail power and video
connections
• One HD4D hardware kit
• One bag containing mounting screws
• One Product warranty
If any parts are missing or damaged, contact the dealer you purchased the camera from or call
Honeywell Customer Service (see Warranty and Service).
Equipment Required
You will require the following tools to complete the installation:
• Phillips screwdriver
• Tools supplied in the hardware kit (three Allen keys): one for the security screw on the lid
one for the conduit plug locking screw, and one for the lens locking screw
•Side-cutters

Document 800-00023 Rev D 7
05/07
Installation
The HD4D is weather-sealed for indoor or outdoor locations. The HD4D is a fully-integrated
enclosure with camera and lens. The wiring can be completely concealed to reduce the risk of
tampering.
Figure 1 Installation Components
HD4D dome
enclosure

8
Mounting the Camera
The HD4D Camera is designed to be surface mounted on a wall or ceiling. Before you
mount the camera, use the mounting template provided to mark and pre-drill the holes.
Connecting Cables Through the Housing Base
For installations requiring pulling cables through the grommet located in the bottom of the
base:
1. Use a sharp knife to cut an !opening in the base gasket (see the figure below). Be
careful. The opening should only be big enough to feed the cable assembly through.
2. Pull the cabling through the opening.
3. Apply appropriate sealant around the opening to prevent moisture from entering the
housing.
Base gasket opening
!

Document 800-00023 Rev D 9
05/07
Connecting Cables Through the Side Conduit
1. Peel back the bottom flat gasket below the side conduit just enough to expose the security
screw.
2. Use the Allen key supplied to loosen and remove the security screw (see below).
3. Use a flat screwdriver to unscrew the conduit plug.
4. Pull the cabling through the hole.
5. Apply appropriate sealant around the opening to prevent moisture from entering the
housing.
security screw
supplied
allen key

10
Electrical Box Installations
Figure 2 illustrates how to mount the HD4D directly to a 4S electrical box or directly to wall
or ceiling. For 4S electrical box installations, the optional adapter plate can be used to
cover ceiling or wall imperfections around the electrical box opening.
Figure 2 4S Electrical Box Installation
Note Honeywell recommends that you orient the conduit plug facing downwards
(wall mount installations) to prevent moisture from entering the housing.
Electrical box
(not supplied)
Adapter plate
(use is optional)
HD4D base
Secure the optional
adapter plate to the
4S electrical box
using appropriate
screws (not supplied)
Secure the HD4D base with
screws appropriate to your
installation (supplied)
For surface mount
installations (without an
electrical box), use
#6-1 7/16 inch slotted Type
A screws (x4) supplied
Ceiling/wall

Document 800-00023 Rev D 11
05/07
Figure 3 illustrates how to mount the HD4D directly to a double gang or single gang
electrical box.
Figure 3 Double Gang/Single Gang Electrical Box Installation (Single Gang Shown)
Electrical box
(not supplied)
HD4D base
Ceiling/wall
Secure the HD4D base with
screws appropriate to your
installation (not supplied)
For surface mount
installations (without an
electrical box), use
#6-1 7/16 inch slotted Type
A screws (x4) supplied

12
Connecting the Wiring
Follow Figure 4 for the wiring connection.
Figure 4 Wiring Connection
Power: 12 VDC
or 24 VAC
+ Red
- Black
Video: female BNC
(yellow)
Note For secure installations, surface
mounted cables should be
protected by plastic or metal
cable covers.

Document 800-00023 Rev D 13
05/07
Adjusting the Camera
To adjust the HD4D Camera:
1. Apply 12 VDC or 24 VAC power to the camera and monitor the video signal.
2. Loosen the screws that lock the gimbal assembly in place (see Figure 5).
3. Adjust the camera carrier to the desired view.
4. Tighten the screws to lock the gimbal assembly in place.
Note Orient the camera as shown in Figure 5 to maintain the correct picture
orientation.
Figure 5 Gimbal Adjustment
Legend
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
Angle viewTop view Setscrews (x2). Loosen to
adjust Pan (C). Other
setscrew located on
opposite side.
B
C
A
Locking screw
Line Lock switch
must be left in
ON position.
Locking screw. Loosen to
adjust Horizontal (B).
Set focus
(top)
Set focal length
(bottom)

14
Line Lock
The Line Lock switch on the power supply board must be left in the ON position. To switch
between Line Lock and Internal Lock, use the OSD menu (see Sync Control Setup, page 19).
Adjusting the Lens Focus
Lenses are pre-focused at the factory but may require a final adjustment after installation in the
unlikely event the optical effect of the dome causes a slight defocusing of the lens.
TECH TIP! To check the focus, hold the dome over the lens while making any adjustments.
To adjust the camera direction, view angle and focus, connect the service monitor cable
(supplied) to the video monitor output.

Document 800-00023 Rev D 15
05/07
Camera Settings
Camera Functions
Figure 6 Camera Controller
RT
DN
LF
Legend
#Description
1Video-test monitor output connector
2Camera OSD control (four position plus center push)
Press this control To do this
UP, DOWN Select a new item
LEFT, RIGHT Select a menu item
SETUP (MENU)
(CENTER PUSH)
Enter SETUP MENU,
access a submenu
1
2

16
OSD Menu Structure
The HD4D camera menu system consists of one main setup menu for easy programming.
SETUP MENU LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
SENS-UP
SPECIAL
EXIT MENU
DC↵
VIDEO
MANUAL
FLK (FLICKERLESS)
ESC↵
MANUAL↵
Main MENU Sub-Menus Options
1
2
3
4
5
6
7
8
ATW
MANUAL↵
AWC↵
OFF
LOW
MIDDLE
HIGH
OFF
LOW↵
MIDDLE↵
HIGH↵
OFF
LOW
MIDDLE
HIGH (with AGC in OFF mode)
OFF
AUTO!(with LENS in MANUAL
mode or SHUTTER in FLX mode)
CAMERA ID
DAY/NIGHT
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET

Document 800-00023 Rev D 17
05/07
SETUP Menu
Menu Item Option Description
LENS DC!
VIDEO
MANUAL
Selects Lens type. Only DC mode is supported at this time.
Caution Selecting VIDEO or MANUAL adversely affects camera operation.
SHUTTER FLK
MANUAL!
ESC!
Adjusts shutter settings.
FLK (Flickerless) reduces on-screen flickering.
MANUAL adjusts the shutter speed from 1/60-1/120,000 of a second (NTSC)
or 1/50-120,000 of a second (PAL). Not available in DC lens mode.
ESC (Electronic Shutter Control) adjusts the brightness level on screen. Not
available in DC lens mode.
WHITE BAL
(White Balance)
ATW
MANUAL!
AWC!
Controls color on the screen.
Select ATW (Auto Tracing White Balance) when the color temp is 2400°K -
12000°K; for example, under a fluorescent light, or outdoors.
MANUAL mode allows you to increase or decrease the red or blue factor on
the screen.
AWC (Auto White Balance Control) automatically adjusts the white balance to
your specific environment.
BACKLIGHT OFF
LOW
MIDDLE
HIGH
Provides light level control to overcome severe backlighting conditions.
AGC OFF
LOW!
MIDDLE!
HIGH!
Adjusts value of AGC (Automatic Gain Control). Increase the GAIN level to
brighten the picture (noise/distortion may develop).
DNR (Digital
Noise Reduction)
OFF
LOW
MIDDLE
HIGH
Reduces noise/distortion on the screen. Increasing the DNR level reduces
noise but may introduce video artifacts. DNR is deactivated if AGC is turned
off.
SENS-UP
(Sensitivity Up)
OFF
AUTO!
Automatically provides a clear image under low-light conditions. You can
control the maximum low-light magnification from 2x to 128x. Increasing
magnification may cause noise/distortion.
EXIT Exits the SETUP menu and returns to video monitoring.

18
SPECIAL Menu
On the main SETUP menu:
1. Press UP or DOWN and then select SPECIAL.
2. Push SETUP (MENU) to access the SPECIAL menu.
Menu Item Option Description
1CAMERA ID OFF
ON
Turns ID display off and on. To add a camera title (name and/or number) to
be displayed on the screen, see Adding a Camera Title Display.
2DAY/NIGHT AUTO
COLOR
BW
When set to AUTO , the camera automatically switches to Night mode
(B/W) when the light level is low.
When set to COLOR,the camera stays in Day mode (Color).
When set to BW, the camera stays in Night mode (B/W).
3SYNC INT
L/L
Synchronizes the vertical interval sync pulse of your camera with other
equipment to reduce the effect of picture roll on the monitor.
Select L/L (Line Lock) mode to adjust the phase from 0° to 359°.
4MOTION DET OFF
ON!
Detects moving objects on screen and displays MOTION DETECTED along
with the number of movements counted. Allows you to select the area on
screen you want to observe (see Motion Detection Setup).
5PRIVACY OFF
ON!
Allows you to mask up to 4 areas of the screen from video monitoring.
6MIRROR OFF
ON
Produces a horizontal mirror image on screen.
7SHARPNESS ON!
OFF
Sharpens the image on screen. You can adjust the sharpness level from 0 -
31 (excessive sharpening may cause picture noise to develop).
8RESET Restores all factory default settings.
RETURN!Returns to the main SETUP menu.

Document 800-00023 Rev D 19
05/07
Adding a Camera Title Display
On the SPECIAL menu, select CAMERA ID, then press SETUP (MENU)..
Sync Control Setup
On the SPECIAL menu, select SYNC, then press SETUP (MENU).
CAMERA ID
A B C D E F G H I J K L M
N O P R Q S T U V W X Y Z
a b c d e f g h i j k l m
n o p q r s t u v w x y z
– . 0 1 2 3 4 5 6 7 8 9
# $ CLR POS END
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1. Press the menu control UP, DOWN, LEFT, or RIGHT
to select a character, then press (SETUP) MENU to
accept it. The character is saved and the title cursor
at the bottom of the screen moves to the next
position. Use the #$ symbols to go backward or
forward in the title name/number to make changes.
Select CLR to delete the entire title and start again.
2. Repeat step 1 until your camera title is complete.
3. Select POS to position the camera title on the
screen. Select the position using the menu control,
then press (SETUP) MENU to confirm the position.
4. Select END when you are finished.
<SYNC. CONTROL>
SYNC INT (L/L)
RETURN!
Menu Item Description
INTERNAL When line lock is not required.
LINELOCK Adjust the vertical phase (VPH):
VPH: 000 - 359 (factory default is 0).
RETURN Press MENU to return to the SETUP menu.

20
Motion Detection Setup
On the SPECIAL menu, select MOTION DET, then press SETUP (MENU).
Privacy Mode Setup
On the SPECIAL menu, select PRIVACY, then press SETUP (MENU).
MOTION DETECTION
AREA SEL AREA 1
AREA STATE ON
TOP |..|................| 10
DOWN |........|..........| 25
LEFT |...|...............| 20
RIGHT |........|..........| 40
Press SET to Return
Menu Item Option Description
AREA SEL AREA 1
AREA 2
AREA 3
AREA 4
Select which of the four motion
detection grids top left, top right,
bottom left, bottom right) you would
like to modify.
AREA
STATE
ON
OFF
Choose whether to activate or
deactivate the selected grid.
TOP
DOWN
LEFT
RIGHT
Press LEFT or RIGHT control to alter
the dimensions of the selected grid.
PRIVACY
AREA SEL AREA 1
AREA STATE ON
AREA TONE |...............|...| 80
TOP |..|................| 10
DOWN |........|..........| 25
LEFT |...|...............| 20
RIGHT |........|..........| 40
Press SET to Return
Menu Item Description
AREA SEL AREA 1
AREA 2
AREA 3
AREA 4
Select which of the four masking
grids (top left, top right, bottom
left, bottom right) you would like to
modify.
AREA STATE ON
OFF
Choose whether to activate or
deactivate the selected grid.
AREA TONE Press LEFT or RIGHT menu
control to change the shade of the
masking grids.
TOP
DOWN
LEFT
RIGHT
Press LEFT or RIGHT menu
control to alter the dimensions of
the selected grid.