HSPT Golden Rainbow AUTOMATIC GOLDEN RAINBOW 10 PLUS User manual
AUTOMATIC GOLDEN RAINBOW 10 +
Residential Cigarette Making Machine
INSTRUCTIONMANUAL
QUICK
START
Register your product now for a one year limited warranty or 20,000 cigarettes, whichever come rst.
( Warranty information on page 4)
Visit our website at www.hsptgoldenrainbow.eu
Patent pending
Failure to abide by standards of tobacco size cut and moisture level as dened
by HSPT Golden Rainbow manufacturer will void the warranty.
IMPORTANT
Tobacco moisture
MUST be between
12% and 20%
(ideally 14% or 15%)
Tobacco length
MUST be between
1/4” to 5/8”
(6mm to 16mm)
RECOMMENDATIONS AND SAFETY
TROUBLESHOOTING
WARRANTY
Recommended usage is to make an average of 2 to 3 pack a day or less. Tobacco only.
HSPT Golden Rainbow 10 +users must be of legal smoking age to use the machine.
Keep the machine and accessories away from children.
Keep and operate the machine in a well-ventilated environment (max.50% humidity) and away from liquids.
Always ensure the machine is unplugged from the electrical outlet before relocating, assembling, disassembling,
or cleaning it.
Don’t touch the machine when in use, some mobile part can cause injury.
Machine doesn’t start its cycle ?
Is the red LED light on front of the machine on?
If not, check if the AC cord is correctly plugged into the machine and/or to an AC plug.
Turn on the back switch and wait for the front red led turn on (expect slight delay)
Cigarette not compacted enough ?
Pause the cycle and check:
• That the set-up of the level control setting is correct. Increase compaction level if needed.
• That there is enough tobacco in the tobacco hopper.
• That the star wheels in the hopper do not have tobacco caught in the gears.
• That the tobacco size cut is at recommended standards (¼”to 5/8” or 6mm to 16mm).
• That the tobacco moisture is at recommended standard (ideal 14 or 15%).
Cigarettes cycle messed-up ?
Pause the cycle and check:
• That tubes are properly loaded and/or well aligned in the tube loader.
• That no tubes are damaged in the tube loader: Oval-shaped,, wrinkled, etc.
• That tobacco size is at standard (1/4”to 5/8”or 6mm to 16mm).
• That Tobacco moisture is at recommended standard (ideal 14 or 15%).
• That tube debris stays at exit of tobacco hopper.
• That the cleaning process was completed at the end of previous cigarette cycle.
AUTOMATIC GOLDEN
RAINBOW 10 +
Residential Cigarette Making Machine
Visit our website at
www.hsptgoldenrainbow.eu
From the date of purchase, the Automatic HSPT Golden Rainbow 10 + comes with a one year limited warranty or 20,000
cigarettes made whichever come rst. Please keep your proof of purchase. - The warranty covers repair of defective parts and
workmanship if the machine was used according to the owner’s manual and manufacturer’s recommendations; including
tobacco size cut and moisture standards. - Warranty will take eect after registration of your Automatic HSPT Golden Rainbow
10 + at www.hsptgoldenrainbow.eu, within 15 days from the date the machine was purchased.
Void of the Warranty
If is Failure to abide by standards of tobacco size cut and moisture level as dened by HSPT Golden Rainbow manufacturer.
If Physical or other damages caused by misuse, abuse, neglect, alterations, unauthorized repair, and machine opening without
manufacturer agreement or lack of proper maintenance.
If the unique machine Serial Number as well as the Quality Control stickers are removed, replaced, or broke and does not
match the machine, it’s original parts, and/or electronic components.
Warranty Exclusions
Cleaning brushes and mat.
Machine and accessories returned to factory must be cleaned and properly packed in an appropriately sized box for return.
WHAT’S IN THE BOX (also include clean mat, cleaning brushes and power cord)
1. Tubes Magazine (for 10 cigarettes at a time).
2. Back carriage opening (cover to be installed).
3. Tobacco hopper (load ONLY recommended tobacco).
4. Discharge chute for cigarette (to be joined).
5. Compaction level control for cigarette density.
6. LED display for turning power on.
7. Pause/Continue cycle button.
8. Start/Stop/Return cycle button.
9. Drawer for recycling excess tobacco (which can be reused).
10. Cigarette counter.
11. Tube Catcher.
12. Plug and Power Switch (Located back of machine).
1
2
3
456
78
910
11
12
QUICK START
WHAT YOU NEED
HOW TO OPERATE
Tube catcher
Use KING SIZE tubes only.
REMOVE any damaged, missshaped
or ‘oval’ tubes from the box.
3
Back Box Carriage
Position and x the back box carriage
to preset screw holes.
1
Load tube magazine
Turn power on. Gently slide down
the tubes in the tube opening
until all tubes are loaded.
5
Suitable tobbaco
Tobacco size MUST be between1/4’ to 5/8”
(6mm to 16mm) and moisture MUST be
between 12% to 20% (ideally 14% or 15%).
4
Power cord
Insert the power cord into the machine
and plug into a power outlet.
2
Load tobbaco and start
Open the the tobacco hopper cover and ll
with approximately 0.5oz (15g) of tobacco
to make 10 cigarettes. Start a cycle.
6
HOW TO INSTALL
COMPLETE INSTRUCTIONS
Brush and run cycle
With the cleaning brushes provided,
clean the tobacco wheel feeder inside
the hopper.
2
Step 1. Power
Insert the power cord into the machine and plug into a
power outlet. When ready to start a cigarette making cycle
turn on the power switch on the back of the machine. The
front led display will turn red after a short delay.
Step 2. Tube catcher
Remove from the box any damaged, misshaped, or “oval”
tubes. Tilt the box to get the tubes perfectly aligned. Place
the tube catcher on the tube lters with the teeth of the tool
between tubes, directing the curve side of the tube catcher
towards the right if you are right handed and left if you are
left handed. With a gentle push you will be able to catch10
tubes at once.
Step 3. Tube loading
Gently slide down the tubes in the tube magazine opening
until all tubes are loaded. Remove the tube loader by pulling
it smoothly away.
While using the tube loader tool is the most ecient way of
loading 10 tubes at once, you can also load the tube loader
by hand. With 2 ngers, gently pick up a fresh, unwrinkled
cigarette tube at the lter. With the lter on the left, at
~30 degree angle, introduce the tube lter rst in the tube
loader. Drop the tube. Ensure that the tube is being placed
correctly and gently in the tube loader. Do not force the
tube into the tube loader. Repeat the operation until you
have loaded all ten tubes. Note: Any damaged tubes will
disturb a proper cigarette making cycle. In both loading
ways, practice can be required.
Step 4. Tobacco loading
Use only tobaccos shown in the table printed on the hopper
cover: the moisture level of the tobacco MUST be between
12% to 20% (ideal 14% or 15%). The length of the tobacco
cut MUST be between 1/4’’ to 5/8’’(6mm to 16mm). The
tobacco chopper and moisture meter supplied with the
Automatic HSPT Golden Rainbow 10 + will help you adjust
your tobacco to the perfect usage standards. Open the
tobacco hopper cover and ll with ~0.5 oz (15 g) of tobacco
to make 10 cigarettes, then close the cover. Note: Use
of tobacco outside these specications will jam and
possibly damage the machine.
Step 5. Starting the cycle and completion
Set-up the tobacco compaction needed on the level
control-setting knob (1 to 3).As you raise the level control
setting you will get a higher degree of compaction in the
tube. Through trial and error you can determine the best
compact setting based on yourown test and the size of
the lter of your favorite cigarette tube brand supplier.
Softly press the “Start/stop/return”button one time to
start the machine. This will produce 10 quality cigarettes
automatically in 2.5 minutes. The machine will automatically
stop at the end of the 10 cigarettes cycle.
If a problem occurs during cigarette cycle
production, press the “Pause /Continue”
button once and x the issue by removing
deteriorated material like damaged
cigarette tubes or by removing excess
tobacco, then resume the cigarette making
cycle by pressing the“Pause/Continue”
button once again.
CAUTION: Ideally, clean the machine after each cycle, never after more than three cycles. Turn o the power switch and
unplug the machine. Empty the machine of all supplies. Next open the tobacco hopper and drawer and the machine tuned
upside-down shaking it gently. This will removed potential tobacco residues stock in the machine. Then, using the brushes
provided, clean the machine as show on the above pictures. Clean the tobacco wheels feeder inside the hopper by pushing
tobacco inside the tobacco chamber (bottom of the tobacco hopper). Then, close the tobacco hopper cover. Turn the machine
back on and run the machine for one cycle with the tube magazine empty to clean the excess tobacco. Recycle the tobacco
from the cleaning process, which might still remain on the cleaning mat (supplied).
Never leave your machine not cleaned when your production is over for the day.
Empty hopper
Remove the drawer for excess tobacco.
1
HOW TO CLEAN
Table of contents
