HTC E-mo1 User manual

HTC True Wireless Earbuds Plus
Quick Start Guide
Model HTC E-mo1
What’s in the box
Earbuds x2
Charging case x1
Quick Start Guide x1
USB Type-C cable x1
Pairs of rubber tips x2 (large and small)
Things to keep in mind with HTC True Wireless Earbuds Plus
HTC True Wireless Earbuds Plus should not be used in extreme
temperatures.
Before using the charging case for the first time, make sure to charge it
using a 5 volt charger.
Pairing HTC True Wireless Earbuds Plus with your phone
1. The earbuds will turn on automatically when you open the charging case.
2. On your phone, go to Settings, turn Bluetooth on, and then pair with
"HTC E-mo1". Check your phone user guide to find out how to access
Bluetooth settings.
Note:
If you don't see the earbuds shown in the list, put them in the charging
case. With the charging case open, repeatedly plug and unplug the
USB Type-C cable thrice. You’ll see the three LEDs flash on then off,
which means the earbuds have been reset.
When the earbuds are on and haven't connected to any mobile device,
they will continue to search for devices. The earbuds will turn off
automatically after 10 minutes.
3. Once paired, the earbuds will automatically connect to your mobile device
when you open the charging case.

4. When you’re not using the earbuds, place them in the charging case to
charge them. Recharge the case with a 5V charger periodically.
Controls:
Power on/off
Open the charging case to turn on the earbuds.
Close the charging case to turn off the earbuds.
Play / Pause
Tap either earbud.
Play next
Double-tap either earbud.
Play previous
Triple-tap either earbud.
Answer call / End call
Tap either earbud.
Decline call
Tap and hold either earbud for 3 seconds.
Assistant
Tap and hold the right earbud.
ANC
(Active Noise reduction)
Tap and hold the left earbud to switch between
these modes:
1. ANC on
2. Ambient sound on
3. Ambient sound off
LED notifications:
Middle LED
When connected to power：
Red: charging the case
Green: case is fully charged
When not connected to power：
Flashing red:charging case is low on battery
Green：charging case has sufficient power
Left and right LED
Orange: charging the earbuds
Off: earbuds are fully charged
Technical specifications:
Product model
HTC E-mo1
Sweat and water resistant
IPX5
Bluetooth range
≦10 m
Bluetooth version
5.0+EDR
Speaker frequency response
20 Hz - 20 kHz
Playback only
Up to 6 hours（Volume level 50%）
Playback with n oise reduction on
Up to 5 hours（Volume level 50%）
Noise reduction only
Up to 9 hours

Talk time
Up to 5 hours（Volume level 50%）
Game time
Earbud charges
(when case is fully charged)
Around 3 charges
Earbud battery capacity
45 mAh
Charging case battery capacity
500 mAh
Charging case input voltage
5V
Charging interface
USB Type-C
Charging case power input rating
5V / 200 mA
Checking product authenticity
1. Scan the QR code on the package
with your phone.
2. Scratch off the coating. You’ll then
see a code.
3. On your phone, enter the last four
4. If the code is authentic, the Search

digits of the code.
results screen will show that you
have a genuine product code.
Warning: If you see the above screen,
beware of counterfeiting.
Legal notice
Trademarks and permissions:
HTC and the HTC logo are trademarks of HTC Corporation and used under license
by Fortune Ship International Industrial Limited.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc.
Copyright © 2021 Fortune Ship International Industrial Limited. All rights reserved.
THIS DOCUMENT IS FOR INFORMATION PURPOSES ONLY, AND DOES NOT
CONSTITUTE ANY KIND OF WARRANTIES.
FCC Warning
FCC ID: 2AVFE-HTCEMO1,only for left earbud.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
Warning：please tear off this isolative film before using.