Hubbell KIM LIGHTING KLV360 User manual

Mini Vault - LTV765/766& KLV360/361/365/366
Installation Instructions
P.O. Box 60080 •16555 East GaleAve.
City of Industry, California 91716-0080
626/968-5666 • FAX [phone]
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Do not overdrive fixtures with greater than 12 volts or fixture over-heating and short lamp life
will occur. This can happen when using other than KIM KLV model transformers.
SAFETY WARNING: Low voltage fixtures can become very hotdepending on the lamp wattage used.
Glass lenses and metal areas above and around the lamp can become hot enough to blister hands. DO
NOT touch the lamp at any time. Particular care should be taken not to locate fixtures where small children can
reach them if higher wattages are used. Lighted lamp is HOT!
CAUTION: Lamp gets HOT quickly. When relamping fixture avoid touching the lamp envelope with bare hands. If
touching the lamp is necessary during installation, clean the envelope with alcohol and dry with a clean, soft
cloth before burning. Contamination of the envelope may reduce lamp performance.
MAINTENANCE: To maintain light efficiency and prevent fixture overheating, glass lenses and enclosures must
be kept clean and free of dirt, dust, leaves, trash and mineral deposits from water. Do notuse these fixtures in
submersible installations such as fountains or swimming pools. Do notinstall luminaire within 10 feet (1.52m) of
a pool, spa, or fountain. Keep away from materials that may burn. DO NOT operate luminaire with missing or
damaged lens.
NOTE: Keep the lamp free from impact while burning, as this may deform the filament and shorten the lamp life.
All electrical work should be done by a qualified electrician. NOT INTENDED FOR INDOOR USE.
KEEP THIS SHEET FOR FUTURE REFERENCE.
Revision 7/16/10 ECN 100715008 Status 13 Part No. 95598
Make certain electrical supply is OFF before starting fixture installations.
LTV765/766
KLV360/361
1. Excavate hole in desired location
approximately 12” in diameter and
about 3” deeper than height of
fixture.
CAUTION:
Do not exceed maximum wattage shown on fixture label.
2. Backfill hole with sand/gravel and
soil for stabiity. Do not backfill with
bark or vermicolite. (May be
installed in concrete, for paved
area installation use Trim Ring,
part no. TR60.)
Tools Required:Flat Head ScrewdriverF” Hex Wrench
!
Socket Head
Cap Screw (5)
3. To open fixture, remove five (5)
socket head cap screws, lens
frame, lens and gasket.
Socket Head
Cap Screw (5)
!
KLV365
KLV366
!

Page 2 KIM Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]
Mini Light Vault - LTV765/766 & KLV360/361/365/366
Installation Instructions
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions
and accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim
Products, are warranted to be free from defects of material and/or
workmanship for a period of 1 year from date of sale, with the
following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers)
provided by and/or included in Kim Products shall carry the
component manufacturer's warranty.
Copper, Bronze and Brass Landscape Components
Copper and Bronze Landscape fixture components shall be
warranted against defects of material and/or workmanship, and
failure due to corrosion, for a period of 25 years from date of sale.
Kim Lighting's brass components are constructed from several
brass parts that are manufactured by various methods at various
times. Since brass naturally deepens in color as it ages through the
normal oxidation process, these parts may exhibit subtle
differences in coloration when the product is new. This is normal
and expected. These color differences will be eliminated shortly
after installation through the normal brass oxidation process.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade,
shall be warranted against defects of material and/or
workmanship, and failure due to corrosion, for a period of 7 years
from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact
with soil, shall be warranted against defects of material and/or
workmanship for a period of 3 years from date of sale. Aluminum
fixture components in direct contact with soil shall be warranted
from defects of material and failure from corrosion for a period of 1
year from date of sale.
Stainless Steel Components
Stainless steel landscape components (Lens Rings) installed in the
outdoor environment shall show signs of oxidation after 5 to 6 years
of install and is dependent on the application and its environment. A
proper maintenance and cleaning program will extend the beauty of
the stainless steel.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in
accordance with applicable Kim instructions, specifications and
accepted trade practices, are covered by the Kim Warranty.
During the warranty period, with proof of purchase, Kim will repair
or replace with the same or similar product, at Kim's option,
without charge. Labor costs are the owner's responsibility and are
excluded from this warranty. This warranty is void if the product is
modified, tampered with, misapplied, poorly installed, improperly
maintained, or subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the
exclusive remedy of the purchaser. This warranty is in lieu of all
other warranties, expressed or implied, including any implied
warranty of fitness for a particular application. Kim Lighting shall
not be liable to the purchaser for indirect or consequential
damages.
LAMP INFORMATION
Catalog Lamp Max
No. Type Watts
LTV765 LED 5
LTV766/KLV360 MR16 75
KLV361 LED 5
KLV365 MR16 75
KLV366 LED 5
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
To Relamp turn off/unplug and allow to cool
before replacing lamp. Replace per chart at
bottom of page. Lamp gets hot quickly. Contact
only switch or plug when turning on.
1
23
4
5
5. Make sure gasket surface is clean and free of all
dirt and debris so a leak free installation can be
achieved. Replace lens, gasket and lens ring.
Secure with socket head cap screws (5). Tighten
opposing screws progressively and evenly.
Rotational
Locking
Screw
Vertical
Locking
Screw
4. Observe warnings & cautions! Install lamp of type
and wattage shown on fixture label (not needed for
LED fixtures). To aim lamp loosen vertical and
rotational locking screws. Aim lamp bracket
assembly to desired orientation & tighten screws.
Remember, the
total wattage
of all lamps
connected to one
transformer must
not exceed the
capacity of that
transformer.
6. Connect fixture cable to main system cable using
a Kim KLV410 Sealed Connector. (See KLV410
Sealed Connector Installation Instructions P/N
95484.)