Hubbell KIM LIGHTING Mini-Vault LTV 764 User manual

Mini-Vault LTV 764 Installation Instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code.
Failure to do so may result in serious personal injury. All work should be done by a qualified electrician.
SAFETY WARNING: Low voltage fixtures can become very hot depending on the lamp wattage used.
Lighted lamp is HOT! Glass lenses and metal areas above and around the lamp can become hot enough to
blister hands. Particular care should be taken not to locate fixtures where small children can reach them if
higher wattages are used. Do not use these fixtures in submersible installations such as fountains or swimming
pools. DO NOT operate luminaires with missing or damaged lens.
MAINTENANCE: To maintain light efficiency and prevent fixture overheating, glass lenses and enclosures must
be kept clean and free of dirt, dust, leaves, trash and mineral deposits from water. For optimum performance a
regularly scheduled maintenance program should be followed.
CAUTION: When relamping fixture avoid touching the lamp envelope with bare hands. If touching the lamp is
necessary during installation, clean the envelope with alcohol and dry with a clean, soft cloth before burning.
Contamination of the envelope may reduce lamp performance.
KEEP THIS SHEET FOR FUTURE REFERENCE.
Revised 7/16/10 ECN 100715008 Status 9 Part No. 95596
1. Excavate hole in desired location approximately 12”
in diameter and about 3” deeper than height of
fixture. Connect housing to conduit system using a
good thread sealant.
LTV764
CAUTION:
To help maintain a clean, dry splice compartment, seal the
conduit entries with RTV.
Do not exceed maximum wattage shown on fixture label.
2.Backfill hole with sand/gravel and soil for stability.
Do not backfill hole with bark or vermicolite. (May be
installed in concrete, for paved area installation use
Trim Ring, part no. TR60.)
Tools Required: Make sure all electrical supply is OFF before beginning fixture installation.
Flat Head Screwdriver F” Hex Wrench Thread Sealant RTV Sealant
!
!
LAMP INFORMATION
Catalog. No Lamp TypeMaximum Watts
LTV764MR16 50
HalogenIntegral Transformer
!
P.O. Box 60080 • 16555 East Gale Ave.
City of Industry, California 91716-0080
626/968-5666 • FAX [phone]

Page 2 KIM Lighting • 16555 E. Gale Ave. • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]
10. Make sure gasket surface is
clean and free of all dirt and
debris so a leak free installation
can be achieved. Replace lens,
gasket and lens ring. Secure
with allen head cap screws (5).
Tighten opposing screws
progressively and evenly to 20
inch/pounds, (1.67 ft. lbs.).
9. Replace socket bracket assembly
and install lamp of type and
wattage shown on fixture label.
To aim lamp loosen vertical and
rotational locking screws. Aim
lamp bracket to desired
orientation & tighten screws.
8. Make wire connections observing
polarity, i.e., green-to-ground,
white-to-common, and black-to-
voltage. Replace splice
compartment cover and
transformer assembly. Place
dessicant package inside
housing. Tighten cover screws to
15 inch/pounds, (1Jft. lbs.).
Mini-Vault LTV764 Installation Instructions
7. Pull field wire through conduit
system and into splice
compartment.
Vertical Locking
Screw
Rotational Locking
Screw
1
2
3
4
5
6. Remove two screws securing
transformer & splice compartment
cover using a flat blade screw-
driver and remove transformer and
cover.
8. Place dessicant package inside
housing.
3. To open fixture, remove five (5)
allen head cap screws, lens
frame, lens and gasket.
Hex Cap
Screw (5)
4. Loosen vertical locking screw.
(Do not remove)
Vertical Locking
Screw
5. Gently compress legs of socket
bracket assembly inward and
remove socket bracket assembly.
Socket Bracket
Assembly

Page 3 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
Mini-Vault LTV764 Installation Instructions
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim Products, are warranted to be free from defects of material
and/or workmanship for a period of 1 year from date of sale, with the following exceptions:
Auxiliary Equipment:
All auxiliary equipment (such as lamps, ballasts, and transformers) provided by and/or included in Kim Products shall carry the
components manufacturer's warranty.
Copper, Bronze and Brass Landscape Components
Copper and Bronze Landscape fixture components shall be warranted against defects of material and/or workmanship, and
failure due to corrosion, for a period of 25 years from date of sale.
Kim Lighting's brass components are constructed from several brass parts that are manufactured by various methods at various
times. Since brass naturally deepens in color as it ages through the normal oxidation process, these parts may exhibit subtle
differences in coloration when the product is new. This is normal and expected. These color differences will be eliminated shortly
after installation through the normal brass oxidation process.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade, shall be warranted against defects of material and/or
workmanship, and failure due to corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with soil, shall be warranted against defects of material and/or
workmanship for a period of 3 years from date of sale. Aluminum fixture components in direct contact with soil shall be
warranted from defects of material and failure from corrosion for a period of 1 year from date of sale.
Stainless Steel Components
Stainless steel landscape components (Lens Rings) installed in the outdoor environment shall show signs of oxidation after 5 to 6
years of install and is dependent on the application and its environment. A proper maintenance and cleaning program will
extend the beauty of the stainless steel.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance with applicable Kim instructions, specifications and
accepted trade practices, are covered by the Kim Warranty. During the warranty period, with proof of purchase, Kim will repair
or replace with the same or similar product, at Kim's option without charge. Labor costs are the owner's responsibility and are
excluded from this warranty. This warranty is void if the product is modified, tampered with, misapplied, poorly installed,
improperly maintained, or subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the exclusive remedy of the purchaser. This warranty is in lieu of all
other warranties, expressed, or implied, including any implied warranty of fitness for a particular application. Kim Lighting shall
not be liable to the purchaser for indirect or consequential damages.