Hubbell GAI-Tronics 12538 Series User manual

Pub. 42003-221A
GAI-TRONICS 3030 KUTZTOWN RD. READING PA 19605 USA
610-777-1374 800-492-1212 Fax: [phone]
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
GAI-TRONICS®
A HUBBELL C OMPAN Y
Speaker Kit and Vacancy Kit
Model 12538-xxx & Model 12539-xxx
Confidentiality Notice
This manual is provided solely asanoperational, installation, and maintenance guide and contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics.
GAI-Tronics retains all intellectual property and other rights in or to theinformation contained herein,
and suchinformation may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not bedisclosed in any form, in whole or in part, directly or indirectly, toany
third party.
General Information
The Model12538-xxx Speaker Kit is intended for use with a Model 234SBM Stanchion Broadcast
Module or a Model 234SBA Stanchion Broadcast Assembly. Each speaker kit consists of a weatherproof
speaker mounted to a gasketed plate and wiring harness to connect to the 10458-xxx Electronics Paging
Module.
Qty Description
1 Speaker Assembly
4 #10-32 tamper-resistant screws
4 Washers, felt
The Model 12539-xxx Vacancy Kit is also used with a Model 234SBM Stanchion Broadcast Module or a
Model 234SBA Stanchion Broadcast Assembly. The vacancy kit is used when less than four speakers are
needed in the stanchion.
Qty Description
1 Vacancy Panel Assembly
4 #10-32 tamper-resistant screws
4 Washers, felt
Installation
1. Install the speaker kit or vacancy kit into the stanchion or broadcast module in the desired direction,
carefully feeding wires down to the access panel cutout for connection to the electronics module.
2. Secure each speaker panel with the four #10-32 tamper-resistant screws and felt washers provided.

Pub. 42003-221A
MODEL 12538-XXX SPEAKER KIT AND MODEL 12539-XXX VACANCY KIT Page: 2 of 2
\\s_eng\gtcproddocs\standard ioms - current release\42003 kit manuals\42004-221a.doc
10/08
3. For the Speaker Kit, remove the four-position connector from the speaker connection in the 10458-
xxx Electronics Paging Module. Connect the BK/W and W/BK wires into the four-position
connector and plug into the speaker connection. Refer to Paging Module Instructions, Pub. 42004-
415.
Figure 1. Typical Application of Speaker Kit and Vacancy Kit
Figure 2. Exploded View of Speaker Kit and Vacancy Kit

(Rev. 10/06)
Warranty
Equipment. GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any
GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall
comply with the then-current product specifications and product literature, and if applicable, shall be fit
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability
of any such third-party warranty will be determined by GAI-Tronics.
Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,
shall be performed in accordance with the standard of care with which such services are normally
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAI-
Tronics warranty obligations with respect to services exceed 100% of the total cost of the services
provided hereunder.
Warranty Periods. Every claim by Buyer alleging a defect in the goods and/or services provided
hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty
periods as set forth above. Provided, however, that if the defect complained of is latent and not
discoverable within the above warranty periods, every claim arising on account of such latent defect shall
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or
should have been discovered by Buyer.
Limitations / Exclusions. The warranties herein shall not apply to, and GAI-Tronics shall not be
responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Return Policy
If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in
accordance with the warranty policy set forth above. Please include a written explanation of all defects to
assist our technicians in their troubleshooting efforts.
Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the
Regional Service Center closest to you.