Hubner U-ONE-SAFETY Compact USC 42 Quick guide

English
Translation of the original configuration
manual
issued
August 2018
ID 74237
Configuration manual
U-ONE
®
-SAFETY-Compact USC 42
Universal-Encoder-System
For the following modules:
SCU-C (Safety Control Unit)
SRC C-R (Safety position switch)
SGS C-R (Safety overspeed switch)
Read the configuration manual prior to assembly,
starting installation and handling!
Keep for future reference!

U-ONE
®
-SAFETY Compact
Configuration manual SCU C / SRC C / SGS C
2
USC42_SCU-KonfigManual-en_R5
Trademark
Brand names and product names are trademarks or registered trademarks of their respective
owner.
Protected trademarks bearing a ™ or
®
symbol are not always depicted as such in the manu-
al.
However, the statutory rights of the respective owners remain unaffected.
Manufacturer / publisher
Johannes Hubner
Fabrik elektrischer Maschinen GmbH
Siemensstraße 7
35394 Giessen
Germany
Phone: [phone]
Fax: [phone]
Internet: www.huebner-giessen.com
E-Mail: [e-mail]
The manual has been drawn up with the utmost care and attention. Nevertheless, we cannot
exclude the possibility of errors in form and content. It is strictly forbidden to reproduce this
publication or parts of this publication in any form or by any means without the prior written
permission of
Johannes Hubner Fabrik elektrischer Maschinen GmbH.
Subject to errors and changes due to technical improvements.
Copyright © Johannes Hubner Fabrik elektrischer Maschinen GmbH.
All rights reserved.

U-ONE
®
-SAFETY Compact
Configuration manual SCU C / SRC C / SGS C
USC42_SCU-KonfigManual-en_R5
3
Table of contents
1 Generally......................................................................................................................... 5
1.1 Abbreviations and terminology used .......................................................................... 5
1.2 System requirements................................................................................................. 5
2 Installing the software.................................................................................................... 5
2.1 Installing the driver manually...................................................................................... 6
2.2 Manual driver installation under Windows XP SP3..................................................... 7
3 Setting up USC 42........................................................................................................... 8
3.1 Planning..................................................................................................................... 8
4 Software description US42Pro....................................................................................... 9
4.1 Fundamental procedure............................................................................................. 9
4.1.1 User interface head section.................................................................................................10
4.1.2 Pulldown menu: File Import Parameters......................................................................... 10
4.1.3 Pulldown menu: File Export Parameters ........................................................................ 10
4.1.4 Pulldown menu: File Report............................................................................................ 10
4.1.5 Pulldown menu: File Offline ............................................................................................ 11
4.1.6 Pulldown menu: Options Language................................................................................. 11
4.1.7 Pulldown menu: Options Login ........................................................................................ 11
4.1.8 Pulldown menu: Options Change password.................................................................... 11
4.1.9 Pulldown menu: Options firmware update...................................................................... 12
4.1.10 Pulldown menu: Options Reset to factory settings .................................................... 13
4.1.11 Pulldown menu: Options Recover password ............................................................. 13
4.1.12 Pulldown menu: Options FitCalc................................................................................ 14
4.1.13 Pulldown menu: Options Determine calibration factor...............................................14
4.1.14 Pulldown menu: “Analysis” switch test...................................................................... 14
4.1.15 Pulldown menu „?“......................................................................................................... 15
4.1.16 Generate support file..................................................................................................... 15
4.1.17 Display calibration settings............................................................................................ 15
4.1.18 Display device data........................................................................................................ 15
4.1.19 Fault memory................................................................................................................. 16
4.2 User interface - display section.................................................................................16
5 Configuring USC 42.......................................................................................................17
5.1 Launching the software US42Pro..............................................................................17
5.2 Operating mode........................................................................................................17
5.2.1 Speed mode ........................................................................................................................ 17
5.2.2 Position and speed mode....................................................................................................17
5.3 Calibrating the position system .................................................................................18
5.3.1 Calibration............................................................................................................................ 19
5.3.2 Determining the calibration factor with two calibration points ............................................. 19
5.3.3 Determining the calibration factor by calculation.................................................................19
5.4 Saving configuration- or parameterisation data in the USC 42..................................20
6 Functions .......................................................................................................................21
6.1 SCU C module..........................................................................................................21
6.1.1 Digital inputs ........................................................................................................................ 21
6.1.2 Digital outputs...................................................................................................................... 22
6.1.3 Current output (non safety related) .....................................................................................23
6.1.4 Configuring the incremental output (non safety-related).....................................................23
6.2 SRC C module..........................................................................................................24
6.2.1 Depiction in the display section........................................................................................... 25
6.3 SGS C module..........................................................................................................25
6.3.1 Underspeed ......................................................................................................................... 26

U-ONE
®
-SAFETY Compact
Configuration manual SCU C / SRC C / SGS C
4
USC42_SCU-KonfigManual-en_R5
6.3.2 Rotation direction dependent............................................................................................... 26
6.3.3 Switching delay.................................................................................................................... 27
6.3.4 Display in the display area...................................................................................................27
6.4 Input accuracy of switching points.............................................................................27
6.5 Error handling ...........................................................................................................28
6.5.1 Error table............................................................................................................................ 29

U-ONE
®
-SAFETY Compact
Configuration manual SCU C / SRC C / SGS C
USC42_SCU-KonfigManual-en_R5
5
1 Generally
The U-ONE®-SAFETY-Compact is referred to as “USC 42” in the following documentation.
This document explains how to set the parameters of the U-ONE®-SAFETY-Compact using
the software US42Pro and then transfer the settings to the device.
1.1 Abbreviations and terminology used
USC 42 U-ONE
®
-SAFETY-Compact universal encoder system
SCU C Module Safety Control Unit
SRC C-R Module safe position switch with positively driven contacts
SGS C-R Module safe speed switch with positively driven contacts
1.2 System requirements
For configuration purposes it is possible to use any commercially available Windows
®
note-
books/PCs that fulfil the following system requirements:
•Windows
®
XP SP3 / Vista / 7 / 8 / 8.1 / 10
•Free space on the HDD: 150 MB (+ Dot Net Framework)
•Available USB 2.0 port
•1 GB RAM, CPU: 1GHz, screen resolution 1024 x 768
2 Installing the software
Ensure the device and your notebook/PC are connected via the USB cable.
Close the automatically started „Found new hardware wizard“ with a click on “Cancel“.
Place the supplied CD containing the software into the CD drive or, alternatively, download
the Setup.exe. If the Setup.exe does not run automatically, navigate via Explorer on the CD-
ROM drive and there start the Setup.exe.
1. The Setup guides you through the installation. Please follow the instructions on the
monitor.
If you use Windows XP, Vista or 7, continue with step 2, users higher operating sys-
tem versions go on to step 3.
2. Windows XP SP3/ Vista / 7
Due to the ended support for your operating system, it is no longer possible for us to
sign the driver; therefore you need to confirm the installation manually. To do this, in
Windows XP, click on “ Continue Anyway ”. In Windows Vista and 7 click on “ Install
this driver software anyway ”. After that, the setup routine will continue.
3. Completion
The software has been installed and starts automatically.
Fig. 2-1: Software Installation 1