Hubsan H107 User manual

Flip tips kindly check page 14-15

1 INTRODUCTION
Thank you for buying HUBSAN products. The quadcopter is designed as an easy to
use, full featured
RC model capable of all forms of rotary flight. Please read the
manual carefully and follow all precautions and recommendations within the manual.
Be sure to retain the manual for future reference, routine maintenance, and tuning.
1.11MPORTANT NOTES
This RC quadcopter
is not a toy, it utilizes various high-tech products and technologies
to provide superior performance.
Please read this manual carefully before operating this product. Improper use
of this
product can result
in serious injury. Be aware of your personal safety, safety of others
and your surrounding environment.
We recommend that you obtain the assistance
of an experienced pilot before
attempting to fly our product for the first time.
2 SAFETY NOTES
2.1 CAUTION
RIC quadcopter have parts that move at high speed, thus posing a certain degree of
danger. Pilots are responsible for any actions resulting
in damage or injury from the
improper operation
of their R/C aircraft models.
Choose a wide open space without obstacles.
Do not operate RIC aircraft near
buildings, crowds
of people, high voltage cables, or trees to ensure the safety of
yourself, others and your model.
Operate this unit within your ability.
Do not fly whilst tired , improper operation may
cause
in danger.
2.2 LiPo Battery Recharging
Your quadcopter
is powered by a Lithium-Polymer (LiPo) battery.
Never recharge your battery whilst it
is inserted in your model. It can catch fire leading
to the destruction of the item .

SAFETY ADVISORY NOTICE
[ Lithium-Polymer (LiPo) Batteries]
LiPo batteries differ from conventional batteries in that their chemical contents are
encased
in a relatively insubstantial foil packaging. This has the advantage of
significantly reducing their weight, but does make them more susceptible to
damage if roughly
or inappropriately handled. As with all batteries, there is a risk
of fire or explosion if safety practices are ignored:
Charge and store LiPo batteries in a location where a battery fire or
explosion (including smoke hazard) will not endanger life or property
Keep LiPo batteries away from children and animals
Consider how you would deal with a LiPo battery fire/explosion as part
of your
normal home Fire Safety & Evacuation Planning
Never charge a LiPo pack that has ballooned or swelled due to
over-/under-charging or from a crash
Never charge a LiPo battery pack that has been punctured or damaged
in a
crash (After a crash, inspect the battery pack for the sign
of damage. Discard
in accordance with your country's recycling laws.).
Do not charge LiPo batteries near flammable materials
or liquids
Ensure that charging leads are connected correctly. Reverse polarity charging
can lead to battery damage or a fire
or explosion
Never charge a LiPo battery
in a moving vehicle
Only charge your LiPo battery using the supplied "balanced" charger
Have a suitable( electrical type) fire extinguisher near the charging area OR a
large bucket
of dry sand. Do not try to extinguish electrical (LiPo) battery fires
with water
Reduce risks from fire/explosion by storing and charging LiPo batteries inside
a suitable container: a LiPo Sack
or metal/ceramic container is advised
Monitor recharging LiPo batteries for signs
of overheating
Never over charge a LiPo battery
Never leave a LiPo battery unattended during recharging
Protect your LiPo battery from accidental damage during storage and
transportation. (Do not put battery packs
in pockets or bags where they can
short circuit
or can come into contact with sharp or metallic objects.)
If your LiPo battery is subjected to a shock (such as a helicopter crash) you
should place it in a metal container and observe for signs of swelling or
heating for at least 30 minutes
0 Do not attempt to disassemble
or modify or repair a LiPo battery

2.3 PREVENT MOISTURE
R/C models are composed
of many precision electrical components.
It is critical to keep the model and associated equipment away from condensation and
other contaminants. Exposure to water or moisture may cause the model to
malfunction resulting
in loss of responsiveness, or a crash .
2.4 PROPER OPERATION
For the safety purpose, please only use hubsan's spare parts for replacement.
2.5 ALWAYS BE AWARE OF THE ROTATING BLADES
When
in operation, the main and tail rotor blades will be spinning at high speed. The
blades are capable of inflicting serious body injury and damage to the environment.
Be cautious of your actions and careful to keep your body and loose clothing away
from the blades. Never take your eyes off the model or leave it unattended while it
is
turned on. Once landed, immediately turn off the model and transmitter.
2.6 AVOID FLYING ALONE
Beginners should avoid flying alone whilst learning flight skills. It
is advised that an
experienced pilot be on hand for guidance.
3 SAFETY CHECK BEFORE FLYING
CAREFULLY INSPECT BEFORE REAL FLIGHT
• Before operation, please check the batteries
of the transmitter and receiver are
charged enough for the flight.
• Before turning on the transmitter, please check that the throttle stick
is in the
minimum position.
• Carefully check rotor blades and rotor holders. Broken or premature failure of parts
will result
in a dangerous situation.
• Check the battery and power plug are securely fastened . Vibration and violent flight
may cause the plug to loosen resulting
in loss of control.
• When turning
on the unit, please follow the power on/off procedure: for Power ON-
please turn on the transmitter first, and then turn on the receiver. For Power OFF-
please turn off the receiver first and then turn off the transmitter. Improper procedure
may cause loss
of control of the quadcopter .

4 TRANSMITTER
4.1 Identification and functional keys
Main Menu
Battery voltage
display -
Elevator trim
(MODE 1)
TRANSMITTER
Data display
Throttle trim
Aileron trim
Battery voltage
display -
(MODE 2)
8 Antenna
4 Elevator Trim
(2) Elevator/Rudder Stick
5 Rudder Trim
8 Antenna
6 Throttle Trim
1 Throttle/Rudder Stick
5 Rudder Trim
(1) Throttle /Aileron stick
Power
Aileron Trim
(MODE 1)
4 Elevator Trim
2 Elevator/Aileron stick
Power
3 Aileron Trim
(MODE 2)

Input Key Function
S/N Identification Function
Forward and backward movement of the stick makes the quad copter
1 Throttle/ Rudder Stick
ascend and descend respectively. Left and right movement of the
stick will rotate the quadcopter's fuselage left/right respectively.
Forward and backward movement of the stick makes the quad copter
2 Elevator/ Aileron Stick
move forward and ba c kward respectively . Left and right mo v ement of
the stick makes the quadcopter drift sideways left/right respecti v ely .
Forward and backward movement of the stick will make the quadcopter
(1) Throttle /Aileron stic k
increase or decrease speed respectively . Left and ri ght movement
of the stick makes the quadcopter roll left/right to initiate a turn .
Forward and backward movement of the st i ck makes the quadcopter
(2) Elevator/ Rudder Stick nose point up / down respectively. Left and right movement of the
stick makes the quadcopter yaw left/right respectively.
3 Aileron Trim Aileron trim subsidiary adjusts left and right drift.
4 'Elevator Trim Elevator trim subsidiary adjusts forward and bac k ward movement.
5 Rudder Trim Rudder trim subsidiary adjusts left and right rotation .
6 Throttle Trim Throttle trim subsidiary adjusts ascent and descent.
7 Power SW
Pushing up switches on the po wer transmitter, pulling down
switches it off.
8 Antenna Transmits wireless signal
4 .2 Reversing channel setup
4.2.1.ELEV REVERSE SET UP
Hold down the Elevator/Aileron or ( mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status, press Elevator Trim key up or down to choose reverse,and
then hold down the Elevator/Aileron stick for 1 second to confirm and exit.

[
.J
M1
•!
--- ._ _ __ _ ___ __ _ - - - - -
~22 . ~L E R E VERSESETUP
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status, press Aileron Trim key left or right to choose reverse ,and
then hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second
to confirm and exit.
i
[
.]
M1 i
-- - :J-
4.2.3. RUDD REVERSE SET UP
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status,press Rudder Trim key left or right to choose reverse,and
then hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second
to confirm and exit.
i i
s E2
______ _ ____ : -:J

4.2.4. EXPERT MODE REVERSE SET UP
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status, press Throttle Trim key
up or down to choose reverse ,and
then hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second
to confirm and exit.
[.]
M1 ,
'E I
_ _ _ _ __ _ _ _ _ _ _
t
4.3 SENSITIVITY SET UP
4.3.1 RUDDER SENSITIVITY SET UP-NOR MODE
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status, press Throttle/Rudder or( mode 1 :Elevator/Rudder) key until
the three-point dotted line symbol start to flash( see picture below), press Rudder
Trim to idea sensitivity and then hold down the Elevator/Aileron or (mode 1 :
Elevator/Rudder) stick for 1 second to confirm and exit.
[] M1 s [J
Flashing - : : !
- - - - - - ----- - -- - - - - -
4.3.2. ELEV SENSIVITY SET UP- NOR MODE
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status, press Throttle/Rudder or( mode 1 :Elevator/Rudder) key until
the three-point dotted line symbol start to flash(see picture below),press Elevator
Trim to idea sensitivity and then hold down the Elevator/Aileron or (mode 1 :
Elevator/Rudder) stick
fo r 1 second to confirm and exit.

[]
s
M1
----- --------- -----
4.3.3 AILE SENSIVITY SET UP- NOR MODE
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status,press Throttle/Rudder or( mode 1 :Elevator/Rudder) key until
the three-point dotted line symbol start to flash( see picture below), press Aileron
Trim to idea sensitivity and then hold down the Elevator/Aileron
or (mode 1 :
Elevator/Rudder) stick for 1 second to confirm and exit.
[]
n
M1
_ _ _ _ ___________ : _ _
4.3.4 RUDDER SENSITIVITY SET UP- EXPERT MODE
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status, press Throttle/Rudder or( mode 1 :Elevator/Rudder) key until
the five-point dotted line symbol start to flash( see picture below), press Rudder
Trim to idea sensitivity and then hold down the Elevator/Aileron
or (mode 1 :
Elevator/Rudder) stick for 1 second to confirm and exit.
so [J
, M1 M2 ,
: __ _ _ _ J

4.3.5. ELEV SENSIVITY SET UP- EXPERT MODE
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status, press Throttle/Rudder or( mode 1 :Elevator/Rudder) key until
the five-point dotted line symbol start to flash( see picture below),press Elevator
Trim to idea sensitivity and then hold down the Elevator/Aileron or (mode 1 :
Elevator/Rudder) stick for 1 second to confirm and exit.
[]
s n
M1
Expert !
-- -- -- - --
4.3.6 AILE SENSIVITY SET UP- EXPERT MODE
Hold down the Elevator/Aileron or (mode 1 : Elevator/Rudder) stick for 1 second to
enter the setting status,press Throttle/Rudder or( mode 1 :Elevator/Rudder) key until
the five-point dotted line symbol start to flash( see picture below), press Aileron Trim
to idea sensitivity and then hold down the Elevator/Aileron or (mode 1 :
Elevator/Rudder) stick for 1 second to confirm and exit.
S [J
4.3Batte ry Mounting
Notice:
>Do not mix old and new batteries
>Do not mix different types
of batteries
>Do not charge non-rechargeable battery.
Release the screw Take out the cover lnstall4 x AAA battery
according to the correct polarities

Return the cover Fasten the screw
5 Li-Po Battery Charging
5.1 The quadcopter equipped with a 3.7V 240mAh Lipo battery
1.Take out the battery from bottom of the quadcopter.
2. Connect the battery with USB charger, the LED light is ON whilst charging
and turns OFF when charging complete.

5.2.Piease refer to 2.2. Safety Advisory Notice
Always partially charge your LiPo battery before storage. LiPo batteries retain a
charge over a reasonable period; It
is not normally necessary to recharge stored
LiPo batteries unless stored for periods longer than 3-6 months.
If your LiPo battery has been over-discharged, it will not
be possible to recharge it
again.
LiPo Battery Disposal & Re-Cycling
Lithium-Polymer (LiPo) batteries must not be placed in with household refuse . Please contact
your
Local Authority (Council) or the supplier of your model for local regulations and the location
of your nearest LiPo battery recycling centre.
TEMPORARY STORAGE of DAMAGED liPo BATTERIES:
Bury the liPo battery in a bucket of Q!Y sand or (if discharged) the battery may be neutralized by immersion in a salt water bath.
If in doubt: always seek expert advice!
6. Start to fly
6.1 Power-On (Failsafe) Procedure
Your RC quadcopter's 4-in-1 Gyro Receiver
is fitted with a Power-On failsafe.
This
is designed to ensure that the quad copter's motor will not start unless it detects a
suitable radio-control signal when the LiPo battery
is connected. The correct Start-Up
sequence
is as follows:
6.1.1 Minimize the throttle to zero position

6.1.2 Power on the transmitter
6.1.3 Switch on the quadcopter by connecting the battery cables with correct polarity
6.1.4 Insert the battery to the bottom
of your quadcopter, make sure the battery
need to
be pushed to the end of the battery compartment.
Tip: You no need to adjust the rudder trimming button if the quadcopter keep left
turn or right turn during flight, The quadcopter will find the rudder central point
automatically
in 3 secondes after the quadcopter landing on a horizontal ground
Landing on a horizontal ground

6.2 Effect of Control
CAUTION: To avoid loss of control: ALWAYS move the controls S-L-0-W-L-Y! Be
aware that control inputs will reduce available lift (see 'Helicopter Principles
of
Flight'). Be ready to use a little extra Throttle to maintain height during maneuvers.
{J. Down
MODE2 MODE1
Throttle (Collective Power) increases/decreases the Flying Height your quadcopter
MODE2 MODE 1
Rudder (Collective Torque Yaw) rotates your quadcopter's fuselage Left I Right
Elevator (Cyclic Pitch) moves
your quadcopter Forwards/Backwards
MODE 1
LEFT mo veme nt mo vement
CAU TION: Controls will appear reversed
when the model is flying towards you I
Aileron (Cyclic Roll) moves your quadcopter 'sideways' Left/Right

6.3 Aerial Flip Tips.
Flip maneuver can only working under the EXPERT MODE, you need to press
cyclic joystick one time to switch into the expert mode.
[L S [J
MODE2
1 Expert
Your quadcopter can do 360° evertion by pushing the joystick
quickly on the condition that the flight surface forming a 30°angle with the
ground and the quadcopter in the acceleration period from the low height to
high height.
6.3.1 Left side flip
Push the joystick to the right side and then quickly push the joystick from the right to
the left.
6.3.2 Right side flip
Push the joystick to the left side and then quickly push the joystick from the left to
the right.
/

6.3.3 Forward flip
Push the joystick to the back and then quickly push the joystick from the back to the
front
MODE2 MODE 1
6.3.4 Backward flip
Push the joystick to the front and then quickly push the joystick from the front to the
back
MODE2 MODE 1

H107 Spare Part Chart
H107-A01
Body Shell
H107-A04
X4RX
H107-A07
Screw Set
H107-A02
Blades
H107-A05
Battery
H203-16
Transmitter
H107-A03
Motor
H107-A06
USB Charger

H107 FAQ
. Transmitter and Quadcopter can not be binded
Answer: Throttle position need to be minimized to zero.
2. Transmitter led light on and then suddenly off.
Answer: Replace new AAA batteries
3. LCD transmitter not showing the setting interface after hold down the joystick for 1 second .
Answer: Throttle not
in zero position
4. Gyro not working well
Answer :
(1 )Battery voltage lower, (2) Re-binding (3)Land on to the groud for 3 seconds and
take off again.
5. Unable to Flip
Answer: (1) Power not enough , (2) Press the cyclic joystick one time to enter into the expert(flip)
mode.
(3)1n the expert{flip) mode, the sensitivity on each channel should be above 90%, you can
program the sensitivity
in setting interface, please check manual4.3 Sensitivity set up.
6. Quadcopter shaking with noise
Answer: Please check if the canopy, chassis and rotors transformed or the chassis not firmly
joint with canopy.
?.
Switchi11g between low and high rates on the transmitter not very user friendly.
Answer: Press cyclic joystick one time to switch on/off the expert mode and normal mode,
"expert" shows on/off on the LCD .
8. Can not take off
Answer:
(1 )Wrong installation on rotors, Rotors mark with A,B .please check here below picture
shows. (2)Wrong installation on motors,please check if each motor installed
in correct position,
there are two different type of motors, you can tell apart from the motor cables, check below
picture shows.
{Top View) (Bottom View)

9. The leg of the quadcopter easy to be taken apart.
Answer: This is a special design to absorb the impact from hard crash, Force the leg back
to the joint position by hand as picture shows.