Hunter Floating Glass Light Kit User manual

Floating Glass Light Kit
Installation Instructions
43525-01 r091107

IMPORTANT: Read all warnings before you begin.
CAUTIONS
• Readentireinstallationinstructionscarefullybeforebeginninginstallationandsavethese
instructions.
• Toavoidpossibleriskofelectricalshockandre,installthislightxtureonlyonHunterceilingfan
TypeA-Z.Findthefanmodelnumberonthefanpackageoronthenameplateontopofthemotor
housing.
WARNINGS
• Toavoidpossibleelectricalshock,beforeinstallinglightxturedisconnectpower
byturningothecircuitbreakersbothtotheoutletboxandtoitsassociatedwall
switchlocation.Ifyoucannotlockthecircuitbreakersintheoposition,securely
fastenaprominentwarningdevice,suchasatag,totheservicepanel.
• Connecthousewiringtothefanbeforeattachingthelightxturetothefan.
• Allwiringmustbeinaccordancewithnationalandlocalelectricalcodes.Ifyouareunfamiliarwith
wiring,youshoulduseaqualiedelectrician.Professionalinstallationisrecommended.
• Toreducetheriskofreorpersonalinjury,allowbulbsandsurroundingsurfacestocooltoroom
temperaturebeforetouchingorremovingthem.
is light fixture is for use only on Hunter Ceiling Fans Type A-Z.
OI
is light fixture weighs 2.12 pounds.
ismanualcontainsinstallationinstructionsforthefollowingmountingmethods:
• FansWithRemovableSwitchHousing
• FansWithNon-RemovableSwitchHousing
• FansWithNon-RemovableSwitchHousingandNoCenterHole
PreparingtheLightKit
1. Disconnectpowerbyturningothecircuitbreakersbothtotheoutletboxandtoits
associatedwallswitchlocation.
2. eshadecoverplatecomesinachoiceofdecorativenishes.Inaddition,thecoverplate
fortheceiling-mountedlighthasnoholeintheside;thecoverplateforthefan-mounted
lighthasaholeintheside.Choosethecoverplatethatappliestoyourdecorating
preferenceandyourmountingpreference.
43525-01 r0911072

OI
43525-01 r091107 3
HunterOriginaland
Non-removableSwitch,
NoCenterHole
Switch
Housing
Plate
Screw
Step 1
Wires
andWire
Connectors Light Kit
Mounting
Plate
Screwand
Washer
Step 3Step 2
InstallingtheLightKitonFansWithNon-RemovableSwitchHousing
andNoCenterHole
1. Uninstallthetwoscrewsfromtheswitchhousingplate.
2. Removethewireconnectorsfromthetwowiresintheswitchhousing
labeled“ConnectLightHere”or“ForLightUse.”Onewireiswhiteandtheotherwire
isblack/whitestriped.
 Connecttheblack/whitestripedwirefromtheswitchhousingtotheblackwirefrom
thelightkit.Connectthewhitewirefromtheswitchhousingtothewhitewirefrom
thelightkit.Secureallwireconnectionsusingwireconnectors.
 Toconnectthewires,holdthebaremetalleadstogetherandplaceawireconnector
overthem,thentwistthewireconnectorclockwiseuntiltight.
CAUTION:Besurenobaremetalwiresorwirestrandsarevisibleaftermaking
theconnections.
3. Finishattachingthelightkittotheswitchhousing.Usethetwoscrewsremoved
fromtheswitchhousingandthelockwashersontheredtag.Screwthelightkitinto
thetwotabsintheswitchhousing.Securelytightenthetwoscrews.
WARNING:Improperinstallationcouldcausethelightxturetofall,orresult
inelectricalshockorpersonalinjury.
4. GototheinstructionsforInstallingBulbs,Chains,Shades.

443525-01 r091107
Screw
Cap
Plastic
Grommets
InstallingBulbs,Chains,ShadeonFan-MountedLights
1. Install60-wattmaximumTypeB-10(candelabra)bulbsintothelamp
sockets.
2. elightkitcomeswiththreepreinstalledplasticgrommets.Checktomake
sureallthreeisolatorsareinplaceattheendsofthemetalarmsandwere
notremovedduringshipment.
3. readthepullchainthroughtheholeinthemiddleoftheglassbowl
4. Lifttheglassbowlandaligntheholesintheglassbowlwiththemetalarms.
5. Slidetheglassbowlontothemetalarms.
6. Installthelooseplasticwashersincludedwiththelightkitontotheendsof
themetalarms.Installthescrewcapsontothemetalarmstosecurewashers
andglassbowlinplace.
7. einstallationiscompleteandyoucanrestorepowertotheceilingfan.
Steps 1–7

InstallingtheLightKitonFanswithRemovableSwitchHousings
1. Unscrewthethreescrewsfromtheupperswitchhousing.Disconnectthe
9-pinplugconnectors.Removethelowerswitchhousing.
2. Pushtheplugfrominsidethelowerswitchhousingtoremovetheplugand
switchhousingcap.
NOTE:Savetheplugbuttonandswitchhousingcapshouldyouchoosetoremove
the light fixture in the future.
3. Feedthetwowiresfromthelightkitupthroughthecenterholeinthelowerswitch
housing.
CAUTION:Ifyourfanisoperatedbyremotecontrol,takecarenottodamage
thesmallcomponentsonthecircuitboardinsidethehousing.
 Screwthreadedrodintothebottomoftheswitchhousing.
 Alignthescrewholesofthelightkitandthelowerswitchhousing.
 Installthenutandwasherontothethreadedrodfromthelightkit.
 Finishattachingthelightkittothelowerswitchhousingusingthetwoattachment
screwsenclosed.Securelytightenthetwoscrews.
WARNING:Improperinstallationcouldcausethelightxturetofall,orresult
inelectricalshockorpersonalinjury.
4. Removethewireconnectorsfromthetwowiresintheswitchhousinglabeled
“ConnectLightHere”or“ForLightUse.”
 Connecttheblack/whitestripedwirefromtheswitchhousingtotheblackwirefrom
thelightkit.Connectthewhitewirefromtheswitchhousingtothewhitewirefrom
thelightkit.Secureallwireconnectionsusingwireconnectors.
 Toconnectthewires,holdthebaremetalleadstogetherandplaceawireconnector
overthem,thentwistthewireconnectorclockwiseuntiltight.
43525-01 r091107 5
OI
RemovableSwitchHousing
Attachment
Screwand
Lockwasher
9-Pin Plug
Connector
LowerSwitch
Housing
Attachment
Screw
Plug
Steps 1-2
Steps 3-4

Hunter Fan Company
2500 Frisco Avenue
Memphis,Tennessee 38114
Printed in China©2007HunterFanCompany
Troubleshooting
Lightdoesnotcomeon.
1. Makesurebulbsareinstalledproperlyandlamentisnotblown.
2. Makesurebreakersorfusesareon.
3. Verifythatthelightpowerleadisconnectedattheceiling.Referto
yourceilingfanmanualforlocatingassemblyandwiring.
Glassrattles.
1. Makesuretheglassglobeissecure.
Forotherproblemsorquestions,contactthe
HunterFanCompanyTechnicalSupportat
US888-830-1326/Canada866-268-1936.
http://www.hunterfan.com
43525-01 r0911076
CAUTION:Besurenobaremetalwiresorwirestrandsarevisibleaftermaking
theconnections.
5. Reconnectthe9-pinplugconnector.
6. Installscrewstoreattachthelowerswitchhousingtotheupperswitchhousing.
7. GototheinstructionsforInstallingBulbs,Chains,Shades.
Wires
andWire
connectors
9-Pin Plug
Connector
Screw
Steps 5-6