HunterDouglas PowerView User manual

PowerView Scene Controller QuickStart Guide
Rev. 4
Buttons
– 1-press activation of favorite Scene
– 1-press activation of second favorite Scene
– activates Scene shown on display/Program mode/Program menu selections
- scroll buttons for cycling through Scene name list

Configuring the Scene Controller
You will need the PowerView Hub to be powered up and connected to a wireless router before configuring the
Scene ontroller.
1. Remove battery tabs to activate controller
2. Press and hold the button for 4 seconds until the buttons begin to flash.
3. Open the PowerView App on your mobile device.
4. Select the Add New ontroller menu option in the PowerView App (under Hub Settings)
5. Follow the instructions on the app screen to configure the Scene ontroller
The Scene ontroller is now joined to the same PowerView Shade Network as the PowerView Hub.
•Use the PowerView App to configure which Scene names are displayed on the Scene ontroller.
Programming
1. Press and hold for 4 seconds to put Scene ontroller into Program mode
2. Use the buttons and to navigate programming menu/options:
a. “Update ?” – scene controller communicates with Hub to get updated Scene name list
information
b. “Join Hub?” – used to join scene controller to Hub (initial setup only)
c. “Reset?” – clears all programming from Scene ontroller
d. “Exit” – exits Program mode
O eration
1. To wake the Scene ontroller, press any button key
2. Use the Scroll buttons to cycle through Scene name list that was configured using the
PowerView App and stored in the PowerView Hub.
3. Press to activate the Scene displayed on the screen.
a. The Scene name displayed with blink until the command has been confirmed by the Hub.
Note: The last Scene activated is displayed on screen.

Battery Re lacement:
1. Remove over.
Press notch to move cover slightly
clockwise to release and remove cover.
3. Replace over.
Position cover over slots. Press notch to
move cover slightly counterclockwise to
lock into position.
U.S. Radio Frequency FCC Compliance
Press notch to move cover slightly
clockwise to release and remove cover.
2. Place Batteries.
Use two R 2032 3V batteries. Slide one
battery into each compartment and press into
place to fully seat.
Position cover over slots. Press notch to
move cover slightly counterclockwise to
4. Battery Removal
To remove batteries use a small screwdriver or
fingernail to lift
battery and remove from slot.
Use two R 2032 3V batteries. Slide one
battery into each compartment and press into
To remove batteries use a small screwdriver or
battery and remove from slot.

This device complies with Part 15 of the F Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a lass B digital device, pursuant to Part 15 of the F
designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfere
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful int
reception, which can be determined by turning the equipment
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• onnect the equipment into an outl
et on a circuit different from that to which the receiver is connected.
• onsult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s a
Industry Canada
Under Industry anada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
transmitter by Industry anada. To reduce potential radio
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry anada licence-
exem
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of
lass B Digital Device Notice
This lass B digital apparatus complies with anadian I ES
Industrie Canada
onformément à la réglementation d’Industrie anada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
inférieur) approuvé pour l’émetteur par Industrie anada. Dans le but de réduire les risques de brouillage radioélectrique à
il faut choisir le type d’antenne et son gain de sorte que la puissance
l’établissement d’une communication satisfaisante.
Le présent appareil est conforme aux NR d’Industrie anada applicables aux appareils radio exempts de licence. L’exploitat
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter to
même si le brouillage est susceptible d’en compromettre le fonctionn
Appareil Numérique de la lasse B – Avis
et appareil numérique de la classe B est conforme à la norme NMB
AN I ES-3 (B)/NMB-3(B)
European Conformity
We, the undersigned,
Hunter Douglas Window Fashions
Address: One Duette Way, Broomfield, O 80020, USA
Authorized representative in Europe:
Hunter Douglas Europe B.V.
Piekstraat 2, 3071 EL Rotterdam, The Netherlands
certify and declare under our sole responsibility that the
2004/108/E and R&TTE directive 1999/5/E .
A copy of the original declaration of conformity may be found at
This device complies with Part 15 of the F Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a lass B digital device, pursuant to Part 15 of the F
Rules. These limits are
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfere
nce to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful int
erference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
• Increase the separation between the equipment and receiver.
et on a circuit different from that to which the receiver is connected.
• onsult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s a
uthority to operate the equipment.
Under Industry anada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
transmitter by Industry anada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
exem
pt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of
the device.
This lass B digital apparatus complies with anadian I ES
-003, RSS-Gen and RSS-210.
onformément à la réglementation d’Industrie anada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
inférieur) approuvé pour l’émetteur par Industrie anada. Dans le but de réduire les risques de brouillage radioélectrique à
l’intention des autres utilisateurs,
il faut choisir le type d’antenne et son gain de sorte que la puissance
isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à
Le présent appareil est conforme aux NR d’Industrie anada applicables aux appareils radio exempts de licence. L’exploitat
ion est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter to
ut brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionn
ement.
et appareil numérique de la classe B est conforme à la norme NMB
-003, NR-Gen et NR-210 du anada.
certify and declare under our sole responsibility that the
PowerView
™
Scene ontroller
conforms with the essential requirements of the
A copy of the original declaration of conformity may be found at
www.hunterdouglas.com/RFcertifications.
Rules. These limits are
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio
nce to radio communications. However,
erference to radio or television
off and on, the user is encouraged to try to correct the interference by one or more of the
uthority to operate the equipment.
Under Industry anada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the
interference to other users, the antenna type and its gain should be so chosen that the equivalent
pt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
the device.
onformément à la réglementation d’Industrie anada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
d’un gain maximal (ou
l’intention des autres utilisateurs,
isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à
ion est autorisée aux deux
ut brouillage radioélectrique subi,
conforms with the essential requirements of the
EM directive