Husqvarna HU700H User manual

Gasoline containing up to 10% ethanol (El 0) isaccept=
able for use inthis machine, The use ofany gasoline e×=
ceeding lO%ethanol (ElO)wilI voidthe productwarranty,
Vous pouvez utiliser de ressence contenant jusqu'a
10 % d'ethanol (El0) avec cet appareil. L'utilisation
d'essence contenant plus de 10 % d'ethanol annulera
la garantie du produit,
Operator's Manual
Manuel de L'Operateur
HU700H /961450023
Please read the operator's manual carefully and make sure
you understand the instructions before using the machine.
Lisez tr_s attentivement et soyez certain de comprende
ces instructions avant d'utiliser cette machine.
115 73 10-32 Rev, 4English/French

A SAFETY RULES A
iMPORTANT: THIS CUTTING MACHINEIS CAPABLEOF AMPUTATINGHANDSAND FEETAND THROWINGOBJECTS. FAILURE
TO OBSERVETHE FOLLOWINGSAFETYINSTRUCTIONSCOULDRESULTiN SERIOUSINJURYOR DEATH.
&Look for this symbol to point out im-
portant safety precautions, it means
CAUTION!!! BECOMEALERT!!! YOUR
SAFETY IS INVOLVED.
WARNING: in order to prevent acciden=
tal starting when setting up, transport=
ing, adjusting or making repairs, always
disconnect spark plug wire and place
wire where it cannot come in contact
with plug.
CAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine
has stopped. To avoid severe burns on
contact, stay away from these areas.
&WARNING: Engine exhaust, some of
its constituents, and certain vehicle
components contain or emit chemi=
cais known to the State of California to
cause cancer and birth defects or other
reproductive harm.
&WARNING: Battery posts, terminals and
related accessories contain lead and
lead compounds, chemicals known to
the State of California to cause cancer
and birth defects or other reproductive
harm. Wash hands after handling.
WARNING: This lawn mower isequipped
with an internal combustion engine and
should not be used on or near any
unimproved forest=covered, brush-
covered or grass=covered land un-
less the engine's exhaust system is
equipped with a spark attester meeting
applicable local or state laws (if any).
if aspark attester is used, it should be
maintained in effective working order
by the operator.
In the state of California the above is required by law(Sec-
tion 4442 of the California Public Resources Code). Other
states may have similar laws. Federal laws apply onfederal
lands. A spark arrester for the muffler is available through
your nearest authorized service center.
I. CHILDREN
WARNING: CHILDREN CAN
BE SERIOUSLY iNJURED OR
KILLED BY THIS EQUIPMENT.
Carefully read and follow all of
the safety instructions below.
The American Academy of Pediatrics recommends that
children be a minimum of 12 year of age before operating
a pedestrian controlled lawn mower and a minimum of 16
years of age before operating a riding lawn mower.
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
*Keep children out of the mowing area and under the
watchful care of a responsible adult other than the
operator.
Be alert and turn machine off ifchildren enter the area.
e
eBefore and while walking backwards, look behind and
down for small children.
Never allow children to operate the machine.
II. GENERAL OPERATION
*Read, understand, and follow all instructions on the
machine and in the manual(s) before starting. Be
thoroughly familiar with the controls and the proper
use of the machine before starting.
Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
, Only allow responsible individuals, who are familiar
with the instructions, to operate the machine.
, Clear the area of objects such as rocks, toys, wire,
bones, sticks, etc., which could be picked up and
thrown by blade. Stay behind the handle when the
engine (motor) is running.
Be sure the area is clear of other people before mow-
ing. Stop machine if anyone enters the area.
Do not operate machine barefooted or while wearing
sandals. Always wear substantial footwear with good
ankle support while mowing.
Do not pull mower backwards unless absolutely neces-
sary. Always look down and behind before and while
moving backwards.
Never direct discharged material toward anyone.
Avoid discharging material against a wall or obstruc-
tion. Material may richochet back toward the operator.
Stop blade when crossing gravel surfaces.
Do not operate the mower without proper guards,
plates, grass catcher or other safety protective devices
in place.
See manufacturer's instructions for proper operation
and installation of accessories. Only use accessories
approved by the manufacturer.
, Stop the blade(s) when crossing gravel drives, walks,
or roads.
e
e
Never leave a running machine unattended.
Stop the engine (motor) and wait until the blade comes
to a complete stop before cleaning the machine, re-
moving the grass catcher, or unclogging the discharge
chute.
*Mow only in daylight or good artificial light.
* Do not operate the machine while under the influence
of alcohol or drugs.
2

•Never operate machine in wet grass. Always be sure
of your footing: keep a firm hold on the handle; walk,
never run.
*Disengage the drive system, if so equipped, before
starting the engine (motor).
If the equipment should start to vibrate abnormally,
stop the engine (motor) and check immediately for
the cause. Vibration is generally a warning of trouble.
Always wear eye protection when operating machine.
. Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
When loading or unloadingthis machine, do not exceed
the maximum recommended operation angle of 15°.
. Wear proper Personal Protective Equipment (PPE)
while operating this machine, including (at amini mum)
sturdy footwear, eye protection, and hearing protection.
Do not mow in shorts or open toed footwear.
Always let someone know you are outside mowing.
III. SLOPE OPERATION
Slopes are a major factor related to slip & fall accidents,
which can result in severe injury. All slopes require extra
caution. If you feel uneasy on a slope, do not mow it.
DO:
*Mow across the face of slopes: never up and down.
Exercise extreme caution when changing direction on
slopes.
Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, bumps or hidden objects. Un-
even terrain could cause a slip and fall accident. Tall
grass can hide obstacles.
DO NOR
Do not mow near drop-offs, ditches or embankments.
You could lose your footing or balance.
Do not mow on wet grass or excessively steep slopes.
Poor footing could cause a slip and fall accident.
IV. SAFE HANDLING OF GASOLINE
Toavoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremelyflammable
and the vapors are explosive.
Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
• Use only an approved container.
Never remove gas cap or add fuel with the engine
running.
• Allow engine to cool before refueling.
e
e
Never refuel the machine indoors.
Never store the machine or fuel container where there
is an open flame, spark or pilot light such as a water
heater or on other appliances.
Never fill containers inside avehicle, on atruck or trailer
bed with a plastic liner. Always place containers on
the ground away from your vehicle before filling.
Remove gas-powered equipment from the truck or
trailer and refuel iton the ground. Ifthis is not possible,
then refuel such equipment with a portable container,
rather than from a gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immedi-
ately.
Never overfill fuel tank. Replace gas cap and tighten
securely.
V. GENERAL SERVICE
e
e
Never run a machine inside a closed area.
Never make adjustments or repairs with the engine
(motor) running. Disconnect the spark plug wire, and
keep the wire away from the plug to prevent accidental
starting.
*Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
Never tamper with safety devices. Check their proper
operation regularly. Never do anything to interfere with
the intended function of a safety device or reduce the
protection provided by a safety device.
* Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage. Allow machine to
cool before storing.
. Stop and inspect the equipment ifyou strike an object.
Repair, if necessary, before restarting.
Never attemptto make wheel height adjustments while
the engine is running.
. Grass catcher components are subject to wear, dam-
age, and deterioration, which could expose moving
parts or allow objects to be thrown. Frequently check
components and replace with manufacturer's recom-
mended parts, when necessary.
. Mower blades are sharp and can cut. Wrap the blade(s)
or wear gloves, and use extra caution when servicing
them.
*Do not change the engine governor setting or over-
speed the engine.
*Maintain or replace safety and instruction labels, as
necessary.
TABLE OF CONTENTS
SAFETY RULES ........................................................ 2=3
PRODUCT SPECIFiCATiONS ..................................... 4
CUSTOMER RESPONSIBILITIES ............................... 4
ASSEMBLY ................................................................ 4=5
OPERATION ............................................................ 6=10
MAINTENANCE SCHEDULE ..................................... 11
MAINTENANCE .................................................... 11=14
SERVICE AND ADJUSTMENTS ........................... 15-16
STORAGE ............................................................. 16=17
TROUBLESHOOTING ........................................... 17=18
3

CONGRATULATIONS on your purchase of a new lawn
mower. Ithas been designed, engineered and manufactured
togive youthe best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center/department. We have competent, well-trained
technicians and the proper tools to service or repair this
lawn mower.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your lawn mower
properly. Always observe the "SAFETY RULES".
SERIAL
NUMBER:
DATE OF PURCHASE:
THE MODELAND SERIAL NUMBERS WILL BE FOUND
ON A DECALATTACHED TO THE REAR OFTHE LAWN
MOWER HOUSING.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
PRODUCT SPECIFICATIONS
Gasoline Capacity 1.0 Quarts (0.94 Liters)
and Type: (Unleaded Regular Only)
Oil Type (API SG-SL): SAE 30 (above 0°0 /32°F)
SAE 10W-30 (below 0°0 /32°F)
Oil Capacity: 0.58 Quarts (0.55 Liters)
Spark Plug (Gap: .030"/0.76mm): NGK BPR5ES
Valve Clearance: Intake: 0.006 mm
(_+0.001") Exhaust: 0.008 mm
Blade Bolt Torque: 35-40 ft. Ibs. (47-54 Nm)
CUSTOMER RESPONSIBILITIES
•Read and observe the safety rules.
•Follow a regular schedule in maintaining, caring for
and using your lawn mower.
•Followthe instructions under "Maintenance" and "Stor-
age" sections of this owner's manual.
ASSEMBLY
Read these instructions and this manual in itsentirety before
you attempt to assemble or operate your new lawn mower.
IMPORTANT: THIS LAWN MOWER ISSHIPPED WITHOUT
OIL OR GASOLINE IN THE ENGINE.
Your new lawn mower has been assembled at the factory
with the exception of those parts left unassembled for ship-
ping purposes. All parts such as nuts, washers, bolts, etc.,
necessary to complete the assembly have been placed in
the parts bag. To ensure safe and proper operation of your
lawn mower, all parts and hardware you assemble must
be tightened securely. Use the correct tools as necessary
to ensure proper tightness.
TO REMOVE LAWN MOWER FROM CARTON
1. Remove loose parts included with mower.
2. Cut down two end corners of carton and lay end panel
down flat.
3. Remove all packing materials except padding between
upper and lower handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of carton and check carton thor-
ougly for additional loose parts.
HOW TO SET UP YOUR LAWN MOWER
TO UNFOLD HANDLE (See Figs. 1and 2)
IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS NOT
TO PINCH OR DAMAGE CONTROL CABLES.
1. Raise lower handle section to operating position and
align holes in lower handle with holes in handle brack-
ets.
3. Remove protective padding, raise upper handle sec-
tion into place on lower handle and tighten both upper
("star") knobs.
4. Remove any packing material from around control bar.
Your handles may be adjusted for your mowing comfort.
Refer to "ADJUST HANDLE" inthe Service and Adjustments
section of this manual.
OPERATOR MOWING
PRESENCE POSiTiON
CONTROL
BAR
LOWER
HANDLE
LOWER HANDLE
"STANDARD" KNOB
FIG. 1
2. Insert handle bolts through lower handles and handle
brackets; secure with lower ("standard") knobs. 4

ASSEMBLY
\
/
/
J
HANDLE
BRACKET
FiG. 2
TO ASSEMBLE GRASS CATCHER
(See Fig. 3)
1. Put grass catcher frame into grass bag with rigid part
of bag on the bottom. Make sure the frame handle is
outside of the bag top.
2. Slip vinyl bindings over frame.
NOTE: Ifvinyl bindings aretoo stiff, hold them inwarm water
for a few minutes. If bag gets wet, let it dry before using.
>_--7-'_ \_/ /xx/ '-'_ \_/ /x_/ FRAME
// _ _/ HANDLE
/
VINYL FRAME
OPENING
FIG. 3
INSTALL STARTER ROPE (See Fig. 4)
1. Loosen T-knob.
2. Hold control bar against upper handle.
3. Slowly pull engine starter rope out until rope will slip
into loop of rope guide.
4. Tighten T-knob.
CONTROL BAR
UPPER
ROPE GUIDE T-KNOB
ENGINE
ROPE
FIG. 4
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be used as a
mulcher. To convert mower to bagging or discharging,
see "TO CONVERT MOWER" in the Operation section of
this manual.
5

OPERATION
KNOWYOUR LAWN MOWER. READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR LAWN
MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and
adjustments. Save this manual for future reference.
These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand
their meaning.
FAST SLOW CAUTION CHOKE ENGINE ENGINE FUEL OIL _ ...-_(_)
OR WARNING ON OFF
_ DANGER, KEEP
HANDS AND
READ OWNER'S MANUAL BEWARE OF THROWN OBJECTS KEEP BYSTANDERS AWAY FEET AWAY
PRESENCE CONTROL BAR
CONTROL LEVERS
STARTER
HANDLE
HANDLE KNOBS
GASOLINE FILLER CAP
GRASS
CATCHER
WHEEL HEIGHT
ADJUSTER LEVER
FUEL VALVE LEVER
AIR FILTER
ENGINE OiL CAP WiTH
MULCHER
IMPORTANT." This lawn mower is shipped DOOR SPARKPLUG
WITHOUT OIL OR GASOLINE in the engine. MUFFLER
NOTE: Gasoline containing up to 10% ethanol (El 0) is
acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (El 0) will void the product warranty.
MEETS CPSC SAFETY REQUIREMENTS
Our rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute
and the U.S. Consumer Product Safety Commission. &WARNING: The blade turns when the engine is running.
OPERATOR PRESENCE CONTROL BAR - must be
held down to the handle to start the blade. Release to
stop the blade.
STARTER HANDLE - used for starting the engine. 6
DRIVE CONTROL LEVERS - used to engage power-
propelled forward motion lawn mower.
MULCHER DOOR - allows conversion to discharge or
bagging operation.

OPERATION
The operation of any lawn mower can result in foreign objects thrown into the eyes,
which can result in severe eye damage. Always wear safety glasses or eye shields
while operating your lawn mower or performing any adjustments or repairs. We
recommend standard safety glasses or a wide vision safety mask over spectacles.
Use ear pro-
tectors to
avoid damage
to hearing.
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory for optimum per-
formance. Speed is not adjustable.
ENGINE ZONE CONTROL
CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower inorder to minimize the risk
of blade contact injury. Do not under
any circumstances attempt to defeat
the function of the operator control, The
blade turns when the engine is running.
Your lawn mower is equipped with an operator pres-
ence control bar which requires the operator to be
positioned behind the mower handle to start and
operate the mower.
2. Rotate turnbuckle on drive control to increase drive
speed.
3. Operate mower to test drive speed. Readjust as re-
quired.
4. If condition fails to improve after the above steps
(forward speed remains the same), your drive belt is
worn and should be replaced.
ADJUSTMENT TURNBUCKLE
DRIVE CONTROL (See Fig. 4)
*Self-propelling is controlled by holding the operator
presence control bar down to the handle and pulling
either drive control lever rearward to the handle. The
further toward the handle a lever is pulled, the faster
the unit will travel.
*Forward motion will stop when either the operator pres-
ence control bar or adrive control lever are released. To
stop forward motion without stopping engine, release
a drive control lever only. Hold operator presence
control bar down against handle to continue mowing
without self-propelling.
NOTE: If after releasing the drive control the mower will
not roll backwards, push the mower forward slightly to
disengage drive wheels.
OPERATOR PRESENCE CONTROL BAR
TO ENGAGE
DRIVE CONTROL
DRIVE
CONTROL
LEVERS
DRIVE CONTROL
DISENGAGED
FIG. 4
DRIVE CONTROL ADJUSTMENT (See Fig. 5)
Over time, the drive control system may become "loose",
resulting in decreased speed. There is a turnbuckle on
the drive control housing to increase tension on the drive
cable. Proceed as follows:
FIG. 5
TO ADJUST CUTTING HEIGHT (See Fig. 6)
All four wheels are adjusted by a single lever.
• Pull adjuster lever toward wheel. To raise mower, move
lever forward to desired position. Tolower mower, move
the lever toward the rear.
WHEEL
ADJUSTER
LEVER
LEVER BACKWARD
TO LOWER MOWER
LEVER FORWARD
TO RAISE MOWER
FIG. 6
1. Turn unit off and disconnect spark plug wire from spark
plug. 7

OPERATION
TO CONVERT MOWER
Your lawn mower was shipped ready to be used as a
mulcher. To convert to bagging or discharging:
REAR BAGGING (See Fig. 7)
•Lift rear door of the lawn mower and place the grass
catcher frame hooks onto the grass bag brackets.
•To convert to mulching or discharging operation,
remove grass catcher and close rear door.
SIDE DISCHARGING (See Fig. 8)
•Rear door must be closed.
Open mulcher door and install discharge deflector
under door as shown.
• Mower is now ready for discharging operation.
• Toconvertto mulching or bagging operation, discharge
deflector must be removed and mulcher door must be
closed and locked.
REAR DOOR
GRASS BAG
BRACKET
GRASS
_, CATCHER
HANDLE
CATCHER
FRAME
FIG. 7
SIMPLE STEPS TO REMEMBER
WHEN CONVERTING YOUR LAWN MOWER
FOR MULCHING -
1. Rear door closed.
2. Mulcher door closed and locked.
FOR REAR BAGGING -
1. Grass catcher installed.
2. Mulcher door closed and locked.
FOR SIDE DISCHARGING -
1. Rear door closed.
2. Discharge deflector installed.
ACAUTION: Do not run your lawn mower
without rear door closed or approved
grass catcher in place. Never attempt
to operate the lawn mower with the rear
door removed or propped open.
\\
UNLOCK
LATCH
OPEN MULCHER
DOOR
iNSTALL
DISCHARGE
DEFLECTOR
\\
MOWER IS NOW READY FOR
DiSCHARGiNG OPERATION
FIG. 8
8

OPERATION
TO EMPTY GRASS CATCHER (See Fig. 9)
1. Lift up on grass catcher using the frame handle.
2. Remove grass catcher with clippings from under lawn
mower handle.
3. Empty clippings from bag using both frame handle
and bag handle.
NOTE: Do not drag the bag when emptying; it will cause
unnecessary wear.
GRASS
CATCHER
FRAME
HANDLE
BAG
HANDLE
FIG. 0
BEFORE STARTING ENGINE
ADD OIL (See Fig. 10)
Your lawnmower is shipped without oil in the engine. For
type and grade of oil to use, see "ENGINE" in the Mainte-
nance section of this manual.
= m
I CAUTION: DO NOT overfill engine with I
oil, or it will smoke on startup.
1. Be sure lawnmower is level.
2. Remove oil fill cap/dipstick from oil fill spout.
3. You recieve a container of oil with the unit. Slowly
pour the entire container down the oil fill spout into
the engine.
4. Insert and tighten oil fill cap/dipstick.
IMPORTANT:
Check oil level before each use. Add oil if needed.
Fill to full line on dipstick.
Change the oil after every 25 hours of operation or
each season. You may need to change the oil more
often under dusty, dirty conditions. See "TO CHANGE
ENGINE OIL:'in the Maintenance section ofthis manual.
ADD GASOLINE (See Fig. 10)
• Fillfuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with a
minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
FILLER CAP
OIL FILL
CAP/DIP-
STICK
FIG. 10
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
Alcohol blended fuels (called gasohol
or using ethanol or methanol) can at-
tract moisture which leads to separation
and formation of acids during storage.
Acidic gas can damage the fuel sys-
tem of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage of
30 days or longer. Empty the gas tank,
start the engine and let it run until the
fuel lines and carburetor are empty. Use
fresh fuel next season. See Storage
Instructions for additional information.
Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
TO STOP ENGINE (See Fig. 11)
•Tostop engine, release operator presence control bar.
Wait until blade and all moving parts have stopped and
turn fuel valve to OFF position if you do not intend to
restart the engine soon.
TO START ENGINE (See Fig. 11)
NOTE: Due to protective coatings on the engine, a small
amount of smoke may be present during the initial use of
the product and should be considered normal.
1. Be sure fuel valve is in the ON position.
2. Hold operator presence control bar down to the handle
and pull starter handle quickly. Do not allow starter
rope to snap back.
9

OPERATION
e
ON
FUEL VALVE LEVER
FiG. 11
MOWING TiPS
CAUTION: Do not use de=thatcher blade
attachments on your mower. Such
attachments are hazardous, will dam=
age your mower and could void your
warranty.
Under certain conditions, such as very tall grass, it
may be necessary to raise the height of cut to reduce
pushing effort and to keep from overloading the engine
and leaving clumps of grass clippings. It may also be
necessary to reduce ground speed and/or run the
lawn mower over the area a second time.
For extremely heavy cutting, reduce the width of cut
by overlapping previously cut path and mow slowly.
For better grass bagging and most cutting conditions,
the engine speed should be set in the FAST position.
For side discharge operation, cut ina counterclockwise
direction, starting at the outside of the area to be cut,
in order to spread grass clippings more evenly and
to put less load on the engine. To keep clippings off
of walkways, flower beds, etc., make the first cuts in
a clockwise direction (See Fig. 12).
f
<,J
FIG. 12
If a trail of grass clipping is left on the right side of the
lawn mower during rear discharge operation, mow in
a clockwise direction with a small overlap to collect
the clippings on the next pass.
Pores in cloth grass catchers can become filled with
dirt and dust with use and catchers will collect less
grass. To prevent this, regularly hose catcher off with
water and let dry before using.
Keep top of engine around starter clear and clean of
grass clippings and chaff. This will help engine airflow
and extend engine life.
MULCHING MOWING TIPS
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER
HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE
"CLEANING" iN MAINTENANCE SECTION OF THIS MANUAL.
The special mulching blade will recut the grass clip-
pings many times and reduce them in size so that
as they fall onto the lawn they will disperse into the
grass and not be noticed. Also, the mulched grass
will biodegrade quickly to provide nutrients for the
lawn. Always mulch with your highest engine (blade)
speed as this will provide the best recutting action of
the blades.
Avoid cutting your lawn when it iswet. Wet grass tends
toform clumps and interferes with the mulching action.
The best time to mow your lawn is the early afternoon.
At this time the grass has dried, yet the newly cut area
will not be exposed to direct sunlight.
For best results, adjust the lawn mower cutting height
so that the lawn mower cuts off only the top one-third
of the grass blades (See Fig. 13). If the lawn is over-
grown it will be necessary to raise the height of cut to
reduce pushing effort and to keep from overloading
the engine and leaving clumps of mulched grass. For
extremely heavy mulching, reduce your width of cut
by overlapping previously cut path and mow slowly.
MAX 1/3
FIG. 13
*Certain types ofgrass and grass conditions may require
that an area be mulched a second time to completely
hide the clippings. When doing a second cut, mow
across (perpendicular) to the first cut path.
Change your cutting pattern from week to week. Mow
north to south one week then change to east to west
the next week. This will help prevent matting and
graining of the lawn.
10

MAINTENANCE
MAINTENANCE
SCHEDULE
Check for Loose Fasteners
_ Clean /Inspect Grass Catcher *
Check Tires
_ Check Drive Wheels
Clean Lawn Mower ....
M Clean under Drive Cover ***
O Check Drive Belt /Pulleys ***
_ Check /Sharpen /Replace Blade
R Lubrication
Clean and Recharge Battery **
BEFORE
EACH
USE
v'
v'
v'
AFTER
EACH
USE
EVERY
10
HOURS
v'
EVERY
25 HOURS
OR SEASON
v'
EVERY
100
HOURS
Check Engine Oil level
E Change Engine Oil
N Clean Air Filter
t Inspect Muffler
N Replace Spark Plug
E Replace Air Filter Paper Cartridge
Empty fuel system or add Stabilizer
14
v'
, (if so equipped)
** Electric-Start mowers
*** Power-Propelled mowers
**** Use a scraper
to clean under deck
BEFORE
STORAGE
v'
v'
v'
_4
v'
1 - Change more often ifoperating under a heavy load or in high outdoor temperatures.
2 - Service more often if operating in dirty or dusty conditions.
3 - Replace blades more often when mowing in sandy soil.
4 - Charge 48 hours at end of season. 6 - See "LUBRICATION" in the
5 - And after each 5 hours of use. Maintenance section of this manual.
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must maintain
mower as instructed in this manual. Some adjustments
will need to be made periodically to properly maintain your
unit. At least once a season, check to see if you should
make any of the adjustments described in the Service and
Adjustments section of this manual.
•At least once a year, replace the spark plug, clean or
replace air filter element and check blade for wear. A
new spark plug and clean/new air filter element assure
proper air-fuel mixture and help your engine run better
and last longer.
•Follow the maintenance schedule in this manual.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
LUBRiCATiON
Keep unit well lubricated (See "LUBRICATION CHART").
IMPORTANT: DO NOT OIL OR GREASE PLASTICWHEEL
BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST
AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-
LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE
LUBRICATED,USEONLYA DRY,POWDEREDGRAPHITETYPE
LUBRICANTSPARINGLY.
I
I
I
k
LUBRICATION CHART
/
\
@ ENGINE OIL
f _ _ (_ MULCHER
DOOR
HINGE PIN
J (_ REAR DOOR HINGE
(_ HANDLE BRACKET MOUNTING PINS
(_ SPRAY LUBRICANT
@SEE "ENGINE" IN MAINTENANCE SECTION
11

MAINTENANCE
LAWN MOWER
Always observe safety rules when performing any main-
tenance.
TIRES
*Keep tires free of gasoline, oil, or insect control chemi-
cals which can harm rubber.
* Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
DRIVE WHEELS
Check rear drive wheels each time you mowto be sure they
move freely. The wheels not turning freely means trash,
grass cuttings, etc., may be inside the drive wheel and dust
cover area and must be cleaned out to free drive wheels.
If necessary to clean the drive wheels, check both rear
wheels.
BLADE CARE
For best results, mower blade must bekept sharp. Replace
a bent or damaged blade.
CAUTION: Use only a replacement
blade approved by the manufacturer of
your mower. Using a blade notapproved
by the manufacturer of your mower is
hazardous, could damage your mower
and void your warranty.
TO REMOVE BLADE (See Fig. 14)
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2. Turn lawn mower on its side. Make sure air filter and
carburetor are up.
3. Use a wood block between blade and mower housing
to prevent blade from turning when removing blade bolt.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
4. Remove blade bolt by turning counter-clockwise.
5. Remove blade and attaching hardware (bolt, lock
washer and hardened washer).
6. Remove debris shield.
NOTE: Removethe blade adapter and checkthe key inside
hub of blade adapter. The key must be in good condition
to work properly. Replace adapter if damaged.
TO REPLACE BLADE (See Fig. 14)
1. Position the blade adapter on the engine crankshaft.
Be sure key in adapter and crankshaft keyway are
aligned; and that the drive belt is inside the tab of the
belt retainer.
2. Install debris shield.
3. Position blade on the blade adapter.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE
IN BLADE MUST ALIGN WITH STAR ON BLADE ADAPTER.
4. Be sure the trailing edge of blade (opposite sharp
edge) is up toward the engine.
5. Install the blade boltwith the Iockwasher and hardened
washer into blade adapter and crankshaft.
6. Use block of wood between blade and lawn mower
housing and tighten the blade bolt, turning clockwise.
The recommended tightening torque is 35-40 ft. Ibs.
(47-54 Nm).
IMPORTANT: BLADEBOLTISHEATTREATED.IFBOLTNEEDS
REPLACING,REPLACEONLYWITHAPPROVEDBOLT.
SHAFT
BELT KEYWAY
BLADE
ADAPTER
DEBRIS
SHIELD EDGE
HARDENED
WASH ER
LOCK WASH ER
BLADE BOLT
FIG. 14
TO SHARPEN BLADE (See Fig. 15)
NOTE: We do not recommend sharpening blade - but if
you do, be sure the blade is balanced. An unbalanced
blade will cause eventual damage to lawn mower or engine.
• The blade can be sharpened with afile or on a grinding
wheel. Do not attempt to sharpen while on the mower.
• Tocheck blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer. (When using a
cone balancer, follow the instructions supplied with
balancer.)
NOTE: Do not use a nail for balancing blade. The lobes
of the center hole may appear to be centered, but are not.
Slide blade on to an unthreaded portion of the steel
bolt or pin and hold the bolt or pin parallel with the
ground. If blade is balanced, it should remain in a
horizontal position. If either end of the blade moves
downward, sharpen the heavy end until the blade is
balanced.
CENTER HOLE
5/8" BOLT OR PIN BLADE
12 FIG. 15

MAINTENANCE
GRASS CATCH ER
The grass catcher may be hosed with water, but must
be dry when used.
Check your grass catcher often for damage or dete-
rioration. Through normal use it will wear. If catcher
needs replacing, replace only with approved replace-
ment catcher. Give the lawn mower model number
when ordering.
GEAR CASE
To keep your drive system working properly, the gear
case and area around the drive should be kept clean
and free of trash build-up. Clean under the drive cover
twice a season.
The gear case is filled with lubricant to the proper
level at the factory. The only time the lubricant needs
attention is ifservice has been performed on the gear
case.
ENGINE
Maintenance, repair, or replacement ofthe emission control
devices and systems, which are being done atthe custom-
ers expense, may be performed by any non-road engine
repair establishment or individual. Warranty repairs must
be performed by an authorized engine manufacturer's
service outlet.
LUBRICATION
Use only high quality detergent oil rated with API service
classification SG-SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
SAE VISCOSITY GRADES
°F , -20 0,30 32, 40 ,60 ,80 ,100
°C -30 -2'0 -10 0 10 20 30 40
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
NOTE: Multi-viscosity oils (5W30, 10W30 etc.) improve
starting in cold weather, and you should check your engine
oil level frequently to avoid possible engine damage from
running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before starting the engine
and after each five (5) hours of continuous use. Tighten oil
plug securely each time you check the oil level.
TO CHANGE ENGINE OIL (See Figs. 16 & 17)
NOTE: Before tipping lawn mower to drain oil, empty fuel
tank by running engine until fuel tank is empty.
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2. Remove oil fill cap/dipstick; lay aside on a clean sur-
face.
3. Tip lawn mower on its side as shown and drain oil into
a suitable container. Rock lawn mower back and forth
to remove any oil trapped inside of engine.
CONTAINER
FIG. 16
4. Wipe off any spilled oil from lawn mower or side of
engine.
5. Fill engine with oil. Slowly pour oil down the oil fill
spout into the engine.
6. Wait one minute to allow oil to settle. Use guage on
oil fill cap/dipstick for checking level. Insert dipstick
into the tube and rest the oil fill cap on the tube. DO
NOT thread the cap into the tube when taking reading.
13
OIL FILL CAP /
DIPSTICK
UPPE
MARK_J
FIG. 17
7. Continue adding small amounts of oil and recheck-
ing the dipstick until it reads full. DO NOT overfill, or
engine will smoke on startup.
8. Always be sure to retighten oil fill cap/dipstick before
starting engine.
9. Reconnect spark plug wire to spark plug.
AIR FILTER (See Fig. 18)
Your engine will not run properly and may be damaged
by using a dirty air filter. Replace the air filter every 100
hours of operation or every season, whichever occurs first.
Service air cleaner more often under dusty conditions.
TO CLEAN AIR FILTER
1. Remove cover.
2. Carefully remove cartridge.
3. Clean by gently tapping on a flat surface. If very dirty,
replace cartridge.

MAINTENANCE
CLEAN UNDER DRIVE COVER
CAUTION: Petroleum solvents, such as
kerosene, are not to be used to clean
cartridge. They may cause deterioration
of the cartridge. Do not oil cartridge.
Do not use pressurized air to clean or
dry cartridge.
4. Install cartridge, then replace cover.
SLOT
TAB
CARTRIDIGE
FILTER COVER
FIG. 18
MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
the "PRODUCT SPECIFICATIONS" section ofthis manual.
CLEANING
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER
HOUSING FREE OF BUILT-UPGRASS AND TRASH. CLEAN
THE UNDERSIDEOF YOURMOWERAFTER EACH USE.
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
*Clean the underside of your lawn mower by scraping
to remove build-up of grass and trash.
Clean engine often to keep trash from accumulating.
A clogged engine runs hotter and shortens engine life.
. Keep finished surfaces /wheels free of gasoline, oil,
etc.
With the exception of the water washout port (if
equipped), we do not recommend using a garden
hose to clean the outside of your lawn mower unless
the electrical system, muffler, air filter and carburetor
are covered to keep water out. Water in engine can
result in shortened engine life. 14
Clean under drive cover at least twice a season. Scrape
underside of cover with putty knife or similar tool to remove
any build-up of trash or grass on underside of drive cover.
WATER WASHOUT FEATURE (See Fig. 19)
Your lawn mower is equipped with a fitting that allows
quick and easy cleaning of the underside of the housing.
To use this feature, proceed as follows:
1. Move lawn mower to an area of cut grass or another
hard surface.
NOTE: Water,grass and other debris will drain from beneath
the mower housing during the washout process.
2. Remove grass catcher and discharge chute assembly
from lawn mower.
3. Close mulcher door (if equipped).
4. Connect a garden hose to the fitting where shown.
IMPORTANT: BE SURE THE GARDEN HOSE IS NOT ROUTED
UNDER THE LAWN MOWER HOUSING OR ENTANGLED IN
THE WHEELS.
5. Turn on water supply and check for leaks atthe fitting.
If no leaks are present, start engine (as described in the
Operation section of this manual) and let engine run until
the underside of the lawn mower is clean.
WARNING: Do not engage the drive
Asystem during the washout process.
6. Shut off the engine.
7. Shut off water supply and remove hose from fitting.
&CAUTION: Do not remove hose from
fitting while engine is running. Water
in engine can result in shortened en-
gine life.
8. Start engine (as described in the Operation section
of this manual) and let engine run for a full minute to
remove excess water from mower.
HOSE
FITTING
FIG. 19

SERVICE AND ADJUSTMENTS
CAUTION: TO AVOID SERIOUS iNJURY, BEFORE
PERFORMING ANY SERVICE OR ADJUSTMENTS:
1. Release control bar and stop engine.
2. Make sure the blade and all moving parts
have completely stopped.
3. Disconnect spark plug wire from spark
plug and place where it cannot come in
contact with plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in the Operation
section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the rear wheels of
your mower, is provided to minimize the possibility that
objects will be thrown out of the rear of the mower into
the operator's mowing position. Replace the rear deflec-
tor if damaged.
TO REMOVE DRIVE BELT (See Fig. 20)
1. Remove screws securing rear baffle.
2. Turn mower on its side with air filter and carburetor up.
NOTE: Before tipping lawn mower to remove drive belt,
empty fuel tank by running engine until fuel tank is empty.
3. Remove rear baffle from mower.
4. Disconnect return spring from rear baffle/rear gearcase
belt keeper.
5. Remove blade bolt, Iockwasher, hardened washer and
blade.
6. Remove debris shield.
7. Remove gearcase belt keeper.
8. Remove drive belt.
TO REPLACE DRIVE BELT (See Fig. 20)
1. Place new drive belt on gearcase pulley.
NOTE: Always use factory approved belt to assure proper
fit and long life.
2. Reinstall gearcase belt keeper. Be sure the new drive
belt is inside the tabs of the gearcase belt keeper.
3. Position the blade adapter on the engine crankshaft.
Be sure key in adapter and crankshaft keyway are
aligned; and that the new drive belt is inside the tabs
of the belt retainer.
4.
5.
6.
7.
8.
9.
Reattach return spring to rear baffle /rear gearcase
belt keeper.
Place rear baffle in mower housing.
Reinstalldebris shield.
Reinstall blade. The recommended tightening torque is
35-40 ft. Ibs. (47-54 Nm).
Return mower to upright position.
Reinstall rear baffle screws. 15
REAR
GEARCASE
BELT KEEPER
RETURN
BLADE
ADAPTER
\
\
IDLER
PULLEY
RETAINER
DEBRIS
SHIELD
LOCKWASHER
FiG. 20
WASHER
BOLT
TO ADJUST HANDLE (See Fig. 21)
The handle on your lawn mower has three (3) height posi-
tions - adjust to height that suits you.
1. Remove knob and carriage bolt on one side of the
lower handle.
2. While holding handle assembly, remove knob and
carriage bolt from opposite side, align hole in handle
with desired hole in handle bracket and reassemble
bolt and knob and tighten securely.
3. Align opposite side of handle with same positioning
hole and secure with bolt and knob.
KNOB BOLT
HANDLE
BRACKET
HIGH
/
/
LOW
FIG. 21

SERVICE AND ADJUSTMENTS
ENGINE
Maintenance, repair, or replacement ofthe emission control
devices and systems, which are being done atthe custom-
ers expense, may be performed by any non-road engine
repair establishment or individual. Warranty repairs must
be performed by an authorized engine manufacturer's
service outlet.
ENGINE SPEED
Your engine speed has been factory set.
CARBURETOR
Your carburetor is not adjustable.
IMPORTANT:NEVERTAMPERWITHTHEENGINEGOVERNOR,
WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.
OVERSPEEDINGTHE ENGINE ABOVE THE FACTORYHIGH
SPEEDSETTING CAN BE DANGEROUS. IFYOU THINK THE
ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,
CONTACT YOUR NEAREST HUSQVARNA OR OTHER
AUTHORIZED SERVICE CENTER, WHICH HAS PROPER
EQUIPMENTAND EXPERIENCETO MAKEANY NECESSARY
ADJUSTMENTS.
STORAGE
Immediately prepare your mower for storage at the end of
the season or ifthe unit will not be used for 30 days or more.
LAWN MOWER
2.
3.
When lawn mower isto be stored for a period of time, clean
it thoroughly, remove all dirt, grease, leaves, etc. Store in
a clean, dry area.
1. Clean entire lawn mower (See "CLEANING" in the
Maintenance section of this manual).
Lubricate as shown in the Maintenance section of this
manual.
4.
Be sure that all nuts, bolts, screws, and pins are se-
curely fastened. Inspect moving parts for damage,
breakage and wear. Replace if necessary.
Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
HANDLE (See Figs. 22 and 23)
You can fold your lawn mower handle for storage.
1. Loosen the two "star" handle knobs on sides of the
upper handle and allow handle to fold down to the
rear.
2. Loosen the two "standard" handle knobs on sides of
the lower handle and pivot entire handle assembly
forward and allow it to rest on mower.
3. Reinstall "standard" knobs and carriage bolts to lower
handle or handle brackets for safe keeping.
• When setting up your handle from the storage position,
you must manually lock lower handle into mowing
position.
IMPORTANT: WHEN FOLDINGTHE HANDLEFOR STORAGE
ORTRANSPORTATION,BE SURETO FOLDTHE HANDLEAS
SHOWNORYOU MAYDAMAGETHE CONTROLCABLES.
OPERATOR
PRESENCE
CONTROL
BAR
MOWING
POSiTiON
/\
/\\ \_
/ / _ \
/ / \
/ / / /
j J ._/
I I
I I
I ii //////
j// UPPER
/_llt HANDLE
II/I/fX
UPPER
.// HANDLE
/ "STAR"
KNOB
LOWER
HANDLE
LOWER HANDLE
"STANDARD" KNOB
FIG. 22
HANDLE
BRACKET
16 FIG. 23

STORAGE
ENGINE
FUEL SYSTEM
IMPORTANT: IT ISIMPORTANTTO PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTSSUCH AS
CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING
STORAGE. ALCOHOL BLENDED FUELS (CALLED GASOHOLOR
USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE
WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS
DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL
SYSTEM OF AN ENGINE WHILE IN STORAGE.
•Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
•Never use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in mini-
mizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean en-
gine oil. (See "ENGINE" in the Maintenance section of
this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3. Pull starter handle slowly a few times to distribute oil.
4. Replace with new spark plug.
OTHER
•Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your unit indoors and cover itto give
protection from dust and dirt.
Cover your unit with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe, which allows condensation to form
and will cause your unit to rust.
IMPORTANT: NEVERCOVER MOWERWHILE ENGINEAND
EXHAUSTAREASARE STILLWARM.
CAUTION: Never store the lawn mower
with gasoline in the tank inside a build=
ing where fumes may reach an open
flame or spark. Allow the engine to
cool before storing in any enclosure.
TROUBLESHOOTING POINTS
See appropriate section in manual unless directed to a Husqvarna or other authorized repair center.
PROBLEM CORRECTION
Does not start
CAUSE
1. Dirty air filter.
2. Out of fuel.
3. Stale fuel.
4. Water in fuel.
5. Spark plug wire is disconnected.
6. Bad spark plug.
7. Loose blade or broken blade adapter.
8. Control bar in released position.
9. Control bar defective.
10. Fuel valve lever (if equipped) in OFF position.
il 1. Weak battery (if equipped).
12. Disconnected battery connector (if equipped).
1. Clean/replace air filter.
2. Fill fuel tank.
3. Empty fuel tank and refill tank with fresh,
clean gasoline.
4. Empty fuel tank and refill tank with fresh,
clean gasoline.
5. Connect wire to plug.
6. Replace spark plug.
7. Tighten blade bolt or replace blade adapter.
8. Depress control bar to handle.
9. Replace control bar.
10. Turn fuel valve lever to the ON position.
11. Charge battery.
12. Connect battery to engine.
17

TROUBLESHOOTING POINTS
See appropriate section in manual unless directed to aHusqvarna or other authorized repair center.
CAUSEPROBLEM
Loss of power
Poor cut =
uneven
Excessive
vibration
Starter rope
hard to pull
Grass catcher
not filling
(if so equipped)
Hard to push
Loss of drive
(or slowing of
drive speed)
1. Rear of lawn mower housing or cutting
blade dragging in heavy grass.
2. Cutting too much grass.
3. Dirty air filter.
4. Buildup of grass, leaves and trash under
mower.
5. Too much oil in engine.
6. Walking speed too fast.
1. Worn, bent or loose blade.
2. Wheel heights uneven.
3. Buildup of grass, leaves and trash under
mower.
1. Worn, bent or loose blade.
2. Bent engine crankshaft.
1. Engine flywheel brake is on when control
bar is released.
2. Bent engine crankshaft.
3. Blade adapter broken.
4. Blade dragging in grass.
1. Cutting height too low.
2. Lift on blade worn off.
3. Catcher not venting air.
1. Grass is too high or wheel height is too low.
2. Rear of lawn mower housing or cutting
blade dragging in heavy grass.
3. Grass catcher too full.
4. Handle height position not right for you.
1. Belt wear.
2. Belt off of pulley.
3. Drive cable worn or broken.
4. "Loose" drive control system.
CORRECTION
1. Raise cutting height.
2. Raise cutting height.
3. Clean/replace air filter.
4. Clean underside of mower housing.
5. Check oil level.
6. Cut at slower walking speed.
1. Replace blade. Tighten blade bolt.
2. Set all wheels at same height.
3. Clean underside of mower housing.
1. Replace blade. Tighten blade bolt.
2. Contact a Husqvarna or other authorized
service center.
1. Depress control bar to upper handle before
pulling starter rope.
2. Contact a Husqvarna or other authorized
service center.
3. Replace blade adapter.
4. Move lawn mower to cut grass or other
hard surface before starting.
1. Raise cutting height.
2. Replace blade.
3. Clean grass catcher.
1. Raise cutting height.
2. Raise rear of lawn mower housing one (1)
setting higher.
3. Empty grass catcher.
4. Adjust handle height to suit.
1. Check/replace drive belt.
2. Check/reinstall drive belt.
3. Put belt on pulleys /replace belts if broken.
4. Adjust drive control.
18

"_ f f
REGLES DE SECURITE
IMPORTANT: CETTE MACHINE COUPANTE EST CAPABLE D'AMPUTER LES MAINS, LES PIEDS ET DE PROJETER DES
OBJETS. L'INOBSERVATION DES REGLES DE SECURITE SUIVANTES PUET ETRE LA CAUSE DES BLESSURES SERIEUSES ET
EVENTUELLEMENT MORTELLES.
Ce symbole signale les points importants en
mati_re de s_curit_. IIsignifie -ATTENTION
!!!, SOYEZ PRUDENT !!! VOTRE SECURITE
EST EN JEU.
ATTENTION : D_branchez toujours le fil
de bougie d'allumage et pour pr_venir les
d_marrages accidentels, posez-le de telle
fagon qu'il ne puisse pas entrer en contact
avec la bougie d'allumage lots de I'installa-
tion, du transport, des ajustements ou des
r_parations.
ATTENTION :Le silencieux et d'autres
pi_ces de moteur deviennent extr_mement
chauds Iors du fonctionnement et restent
chauds apr_s que le moteur se soit arr_t_.
Pour _viter des br_lures graves, restez loin
de ces zones.
AVERTISSEM ENT: Les gaz d'_chappement
et certains composants des v_hicules
contiennent ou _mettent des produ, its
chimiques reconnus dangereu× par rEtat
de la Californie, parce que canc_rig_nes
ou t_ratogenes ou responsables d'autres
troubles de la reproduction.
&AVERTISSEMENT : Les homes des bat-
teries, ainsi que toutes les homes et leurs
accessoires contenant du plomb, des d_ri-
v_s du plomb ou des produits chimiques
base ,de plomb, sont reconnus dangereu×
par rEtat de la Californie, parce que can-
c_rig_nes ou t_ratog_nes ou responsables
d'autres troubles de lareproduction. Lavez-
vous soigneusement les mains apr_s les
avoir touches.
&AVERTISSEMENT : Ce tondeuse & gazon
est _quip_ d'un moteur &combustion interne
et il ne doit pas _tre utilis_ sur ou pros d'un
terrain couvert d'arbres, d'arbrisseau×, ou
d'herbe si le syst_me d'_chappement n'est
pas muni d'un pare-_tincelles qui rencontre
les e×igences des lois locales appJicables.
Quand un pare=_tincelles est utilis_, il doit
_tre maintenu en bon _tat de fonctionnement
par I'op_rateur. Un pare-_tincelles pour le si-
lencieux est disponible au centre d'entretien
autoris_ le plus proche.
Dans l'6tat de Californie ceci est exig6 par ta Ioi (Code de res-
sources pubtiques de Californie Section 4442). D'autres provinces
ou zones f_d6rates peuvent avoir des lois similaires. Les lois f_-
d6rales s'apptiquent sur les territoires f6d_raux. Un pare-6tincelle
pour lesilencieux est disponible chez un concessionnaire autoris6.
I. ENFANTS
AVERTISSEMENT: LESENFANTS PEUVENT
ETRE GRAVEMENT BLESSES OU TUES PAR
CET EQUIPEMENT. Lisez attentivement et
respectez toutes les consignes de s_curit_
ci=dessous.
Selon I'Acad_mie am_ricaine de pediatrie, ilfaut que les enfants
aient au minimum 12 ans avant d'utiliser une tondeuse A pousser
et au minimum 16 ans avant d'utiliser une tondeuse autoport_e.
Des accidents dramatiques peuvent survenir si I'utilisateur ne
fait pas attention A la presence des enfants. Les enfants sont
fr_quemment attires par la machine et par la tonte de la pelouse.
Ne croyez jamais que les enfants restent & rendroit oQ vous les
avez vu en dernier.
• Tenir les enfants loin de la zone de travail et sous la surveil-
lance attentive d'un adulte autre que l'op_rateur.
• Soyez vigilant et arr6tez la machine si un enfant p_n_tre
dans I'aire de tonte.
• Avant de reculer et Iorsque vous reculez regardez toujours
vers le baset derriere s'il y a des enfants en bas &ge.
• N'autorisez jamais les enfants A utiliser la machine.
• Soyez particuli_rement prudents Iorsque vous approchez
des angles morts, des buissons, des arbres ou de tout objet
pouvant boucher la vision normate.
II. FONCTIONNEMENT GI_NC:RAL
• II est imperatif, avant de d_marrer ta machine, de life et
de comprendre toutes les instructions pr_sentes dans le/s
manuel/s d'utitisation et sur la machine. Bien connaftre les
commandes et I'utilisation de la machine avant la d_marrer.
• Ne mettez pastes mains ou tespieds pros ou au-dessous des
parties rotatives. Restez loins de l'ouverture de la d_charge
a tout temps.
• Seuls des adultes dignes de confiance connaissant les
instructions doivent 6tre autoris_s a utiliser la machine.
• D_barrassez I'aire de tonte des objets tets que les pierres,
les jouets, les fils m_tattiques, les os, les batons etc. Ces
objets peuvent 6tre soutev_s et projet_s par la lame. Res-
ter derriere ta poign_e Iorsque le moteur est en cours de
fonctionnement.
• Assurez-vous qu'il n'y a personne, en particulier ni animaux
domestiques ni enfants, dans l'aire de tonte avant de com-
mencer atondre. Arr6tez ta machine si quetqu'un s'introduit
dans l'aire de tonte.
• Ne pas faire fonctionner la machine pieds nus ou en portant
des sandales. Lots de latonte, toujours porter des chaussures
offrant un bon maintien des cheviIles.
• Ne faites pas recuter la machine & moins d'y 6tre contraint.
Regardez toujours parterre etderriere vous avant de reculer.
• Ne dirigez jamais t'_vacuation du mat_riau vers tespersonnes.
Evitez de diriger t'_vacuation du mat_riau vers un mur ou un
obstacle. Le mat_riau _vacu_ risque de rebondir en arri_re
vers l'operateur. Arr6tez les lames lorsque vous passez sur
du gravillon.
• N'utitisez jamais la machine si les protections, les plateaux
et tes autres dispositifs de s_curit_ ne sont pas en place.
• Consuttez les instructions du producteur pour connaftre
le mode correct de fonctionnement et d'installation des
accessoires. N'utilisez que les accessoires conseiIl_s par
le producteur.
lg

• Arr6tez les lames Iorsque vous traversez des atl6es gravil-
Ionn6es, des trottoirs ou des rues.
• Ne jamais laisser la machine fonctionner sans surveillance.
• Arr6ter le moteur et attendre jusqu'& ce que la lame soit &
I'arr6t comptet avant de nettoyer la machine, retirer le r6cu-
p6rateur d'herbes ou d_bourrer la goutotte d'_vacuation.
• Tondez uniquement avec la lumi_re du jour ou avec une
bonne lumi_re artificielle.
• N'utitisez pas la machine si vous 6tes sous I'influence de
I'atcoot ou des drogues.
• N'utilisez jamais la machine sur de I'herbe humide. Mar-
chez d'un pas sQr: saisissez bien la poign6e et marchez; ne
courrez jamais.
• Avant de d6marrer le moteur, d_sengager le syst_me d'entraf-
nement, seton 1'6quipement.
• Si la machine commence a vibrer de fa£_onanormale, arr6tez
le moteur et cherchez imm6diatement tacause. Lesvibrations
sont en g6n6rat un signal d'alarme.
• Toujours porter des lunettes de protection Iors de l'utilisation
de la machine.
• Soyez tr_s prudent Iorsque vous approchez des coins
aveugles, arbustes, arbres ou autres objets qui peuvent
obstruer la vision.
• IIne faut pas d_passer un angle maximum de 15° pour
charger et d6charger cette machine.
• Le port d'Equipements de protection individuetle (EPI) appro-
pri6s est conseille pendant I'utitisation de cette machine et
comprend (au moins) des chaussures robustes, des tunettes
de s_curit6 et des protections auditives. Ne tondez pas en
chaussures d6couvertes et/ou a bout ouvert.
Veillez a informer une tierce personne que vous 6tes en train de
tondre & I'ext_rieur.
III. FONCTIONNEMENT DANS LES PENTES
Les pentes sont souvent & I'origine de glissades ou de chutes
pouvant causer de graves btessures. Faites tr_s attention au
cas de pentes. Si vous ne vous y sentez pas en s_curit_ sur les
pentes, ne tondez pas.
FAITES:
,, Tondez paratl_lement & la pente, jamais en mont6e ou en
descente. Faites tr_s attention Iorsque vous changez de
direction.
• Enlevez les obstacles tels que les pierres, les branches les
arbres, etc.
• Prendre garde aux trous, aux orni_res, aux bosses et aux
objets cach6s. Unterrain accident6 peut entrafner une chute.
L'herbe haute peut cacher des obstacles.
NE FAITES PAS:
,, Ne pastondre pros de sur616vations, de foss6s ou d'orni_res.
Vous pourriez perdre votre stabilit6 ou votre 6quilibre.
Ne pas tondre du gazon humide ou sur des pentes trop
raides. Un terrain accident_ peut entrafner une chute.
IV. MANIPULATION SORE DU CARBURANT
Pour 6viter les blessures corporelles et les dommages materiels,
prendre grand soin dans la manipulation de I'essence.
Eteignez les cigarettes, cigares, pipes et autre sources
d'incendie.
,, N'utilisez qu'un bidon homotogu_.
•N'enlevezjamais tebouchon etn'ajoutezjamais de carburant
Iorsque le moteur est en marche.
• Laissez te moteur refroidir avant de le remptir.
• Ne remplissez jamais le r6servoir a l'int6rieur.
• Ne rangez jamais ni I'appareil nile bidon dans un endroit
oQse trouve une flamme nue, des etincelles ou une flamme
pilote (chauffe-eau ou autres appareils).
• Ne remptissez jamais tes bidons darts unevoiture, un camion
ou une remorque rev6tue de plastique. Ptacez toujours
les bidons sur le sol eta I'_cart de votre v_hicule avant le
remplissage.
• Sortez I'appareil a essence du camion ou de laremorque et
remplissez-te au sol. Si ceta n'est pas possible, remptissez-
le avec un bidon portable ptut6t qu'avec un distributeur
pistotet.
• Laissez la buse au contact du bord de t'orifice du r6servoir
d'essence ou du bidon pendant toute la dur6e du remptis-
sage. N'utilisez pas de dispositif dont le pistolet se verrouille
en ouverture.
Si vous versez du carburant sur vos v_tements, changez-
vous imm_diatement.
• Ne remplissez jamais trop le r_servoir. Remettez le bouchon
en place et serrez bien.
V. ENTRETIEN GI_NF:RALE
• Ne faites jamais marcher latondeuse &t'int_rieur d'un espace
ctos.
• Ne faites ni r6glage ni r6paration avec le moteur en marche.
D6branchez le fil de la bougie et 61oignez-te de la bougie
pour 6viter les d_marrages accidentets
• Garder les boulons et 6crous serr6s afin de s'assurer que
1'6quipement est en _tat de fonctionnement s_curitaire.
• N'alterez jamais le fonctionnement normal des dispositifs de
s_curite. V_rifiez r_guli6rement teur bon fonctionnement. Ne
jamais rien faire qui puisse interf_rer avec le fonctionnement
d'un dispositif de s_curit_ ou r_duire la protection fournie
par un dispositif de securite.
• Evitez que des herbes, des feuilles, ou des d_bris en tout
genre ne s'accumutent sur votre machine. Nettoyez les
6ctaboussures d'huile ou d'essence. Laissez refroidir la
machine avant de l'entreposer.
• Dans le cas oQvous heurtez un objet, arr6tez la machine et
v_rifiez l'absence de d_g&ts. Avant de red,matter, r_parez
si n_cessaire les d_g&ts.
• N'essayez jamais de r_gler la hauteur de la roue Iorsque le
moteur est en marche.
• Les 61_ments du bac de ramassage s'usent et peuvent
s'abfmer etse d_t_riorer, risquant ainsi de projeter les parties
en mouvement ou des objets. Contr61ez fr_quemment ces
61_ments et remplacez-les, en cas de besoin, par des pi_ces
de rechange conseillees par le fabricant.
• Les lames de la tondeuse sont affQtees et peuvent couper.
Enveloppez les lames ou portez des gants et faites tr_s
attention Iors des operations d'entretien sur les lames.
• Ne changez pas le r6glage du limiteur de r_gime et _vitez
tout survitesse du moteur.
• Nettoyez ou remplacez au besoin les _tiquettes d'information.
SO E
RI_GLES DE SI_CURITE ........................................ 19-20
SPI_CIFICATIONS DU PRODUIT ............................... 21
RESPONSABILITES DU CLIENT ............................... 21
ASSEMBLAGE ...................................................... 21-22
UTILISATION ......................................................... 23-27 2O
GUIDE D'ENTRETIEN ................................................ 28
ENTRETIEN ........ _................................................. 28-31
REVISIONS ET REGLAGES ................................. 32-33
ENTREPOSAGE .................................................... 33-34
GUIDE DE Di=PANNAGE ..................................... 34-35