Hussmann IMPACT D5RRI Quick start guide

1
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0435047
January, 2003
D5RRI and D5RRIS
Rear Roll-in Dairy
Joining Instruction
Merchandisers
®
PARTS LIST
Item Quantity Description
D5RRI D5RRIS
1. 1 1 Gasket 1/2x 1/2x 60 (1524 mm)
2. 1 1 Gasket 1/2x 15/8x 120 (3048 mm)
3. 9 5 Cap Screw 5/16 -18 x 11/4
4. 9 5 Lock Washer 5/16
5. 9 5 Flat Washer 5/16
6. 1 1 Threaded Rod 1/2-16 x 12 (305 mm)
7. 2 2 Flat Washer 1/2
8. 2 2 Hex Nut 1/2-16
9. 1 1 Silicone Sealer
Note: Nut retainers are factory installed in the left end, and alignment pins are factory installed in
the right end of each merchandiser.
NOTES:
• Be sure merchandisers have been
leveled according to the installation
instructions.
• Be sure factory-installed nut
retainers and alignment pins are in
place.
• Install optional shelf kits after all
merchandisers have been joined.
1Remove front air grille and honeycomb from the right end
as shown in Figure 1.
Right Front
Air Grille
Right Front
Honeycomb
Figure 1. Remove Air Grille and Honeycomb
D5RRI
D5RRIS

2Verify that nut retainers and alignment pins are installed in
the right-hand end of the left
case in the locations shown in
Figure 2.
P/N 0435047
Merchandisers
®
2HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Alignment Pins
Alignment Pins
Figure 2. Verify Nut Retainer and Alignment Pin Installation

3Apply Gasket – 1 along the center of the lower assembly.
Apply Gasket – 2 to cover
foam-to-metal gap at rear and
across top as shown in Figure 3.
Lap gaskets at lower corners.
Check that there are no gaps
between gasket and case.
• Do not stretch gasket,
especially around corners.
• Do not butt gaskets; always lap
joints.
• Remove paper backing after
gasket is applied.
Joining Instruction for D5RRI and D5RRIS
Rear Roll-in Dairy Merchandisers P/N 0435047
3
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Optional
Low Front
2
Standard
1
1
Note: Case To Be
Sealed And
Gasketed As Shown
2
11/2in. x 1/2x 60
1/2in. x 15/8x 120
1
2
Figure 3. Apply Gaskets
Optional
Low Front Standard Front
D5RRI
D5RRIS

4Move second merchandiser against first, mating alignment
pins with corresponding holes.
5Fasten fronts together using Cap Screw – 3,
Flat Washers – 4, and
LockWashers – 5 as shown in
Figure 4. Tighten only until front
panels touch. Do not tighten
fully.
6Use Cap Screws – 3 with Flat Washers – 4 and
Lock Washers – 5 to draw
merchandisers together at rear.
Start at the bottom, then middle,
then top; tighten until gaskets are
compressed.
P/N 0435047
Merchandisers
®
4HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
5
Alignment
Pins
Nut Retainer
9 Places for D5RRI and
5 Places for D5RRIS
3
4
Figure 4. Joining Ends

7Draw canopies together using Rod – 6 through top shoe, and
Washers – 7, and Nuts – 8
on each end of rod as illustrated
in Figure 5. Stop when canopies
touch.
8Apply a bead of Silicone – 9 to the joined merchandisers as
shown in Figure 6. When dry,
replace honeycomb.
Joining Instruction for D5RRI and D5RRIS
Rear Roll-in Dairy Merchandisers P/N 0435047
5
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
876
7
8
Silicone Gun
Silicone Gun Apply Silicone Bead
Apply Silicone Bead
D5RRI
D5RRIS
9
9
Figure 5. Canopy Joining
Figure 6. Applying Silicone