Huvitz HPE-810 User manual

1
1
User Manual
EDGER
HPE-810

2
2
HPE-810
HUVITZ
IMPORTANT NOTICE
This product may malfunction due to electromagnetic waves caused by portable personal
telephones, transceivers, radio-controlled toys, etc. Be sure to avoid having the above objects, which
affect the normal operation of the product, brought near the product.
The information in this publication has been carefully checked and is believed to be entirely accurate
at the time of publication. HUVITZ assumes no responsibility, however, for possible errors or
omissions, or for any consequences resulting from the use of the information contained herein.
HUVITZ reserves the right to make changes in its products or product specifications at any time and
without prior notice, and is not required to update this documentation to reflect such changes.
9000ENG0025-A
Ver 1.0 (Jun. 2015)
©2015 HUVITZ Co., Ltd.
298-29 Gongdan-ro, Gunpo-si, Gyeongi-do
435-862, Republic of Korea
All rights reserved.
Under copyright laws, this manual may not be copied, in whole or in part, without the prior written
consent of HUVITZ Co., Ltd.

3
3
CONTENTS
1. Introduction......................................................................................................................................6
1.1. Main Functions.......................................................................................................................6
1.2. System Configuration.............................................................................................................7
1.3. Classification..........................................................................................................................8
2. Safety Information............................................................................................................................9
2.1. Introduction ............................................................................................................................9
2.2. Safety Symbols ....................................................................................................................10
2.3. Environmental Considerations..............................................................................................11
2.4. Safety Precautions ...............................................................................................................13
3. System Overview ...........................................................................................................................17
3.1. Edger (HPE-810)..................................................................................................................17
3.2. Frame Reader (HFR-8000) ..................................................................................................20
3.3. Blocker (HMB-8000).............................................................................................................21
3.4. Standard Accessory (Tool Box) ............................................................................................22
4. Installation Procedure ...................................................................................................................23
4.1. Edger ...................................................................................................................................23
4.2. Frame Reader......................................................................................................................24
4.3. Blocker.................................................................................................................................24
5. Operation........................................................................................................................................25
5.1. Frame Reader......................................................................................................................25
5.1.1. Control Panel........................................................................................................25
5.1.2. Frame Tracing ......................................................................................................26
5.1.3. Pattern Tracing .....................................................................................................26
5.2. Blocker.................................................................................................................................27
5.2.1. Scale Plate ...........................................................................................................27
5.2.2. Lens Adapter Setter..............................................................................................27
5.2.3. Blocking Mode ......................................................................................................27
5.2.4. Operation..............................................................................................................29
5.3. Edger ...................................................................................................................................31
6. Edger User Interface ......................................................................................................................32
6.1. Main Screen.........................................................................................................................32
6.1.1. Side Button...........................................................................................................32
6.1.2. Job Management ..................................................................................................34
6.1.3. Frame Information ................................................................................................37
6.1.4. Layout Option .......................................................................................................37
6.1.5. Edging Option.......................................................................................................41
6.1.6. Detailed Edging Option .........................................................................................48
6.1.7. Function Button.....................................................................................................50
6.2. Manual Bevel/Groove Position Modification..........................................................................51
6.2.1. Base Position........................................................................................................51
6.2.2. Region Selection...................................................................................................52
6.2.3. Position Modification.............................................................................................54
6.2.4. Reset & Apply Button............................................................................................58
6.3. Partial Grooving Screen .......................................................................................................59
6.3.1. Region Selection...................................................................................................60
6.3.2. Processing Type Selection....................................................................................62
6.3.3. Safety Bevel Button ..............................................................................................63
6.3.4. Reset & Apply Button............................................................................................63

4
4
HPE-810
HUVITZ
6.4. Job Manager........................................................................................................................64
6.4.1. Job selection tab...................................................................................................64
6.4.2. Function Button.....................................................................................................65
6.4.3. Waiting Job...........................................................................................................65
6.4.4. Working Job..........................................................................................................66
6.4.5. Completed Job......................................................................................................66
6.4.6. Job Search ...........................................................................................................67
6.5. Digital Pattern ......................................................................................................................69
6.5.1. Enlargement/Reduction ........................................................................................69
6.5.2. Near Vision Area Enlargement/Reduction.............................................................71
6.5.3. Rotation ................................................................................................................72
6.5.4. Partial Modification ...............................................................................................74
6.5.5. Reset....................................................................................................................75
6.5.6. Toggle R/L Sync ...................................................................................................76
6.5.7. Exit .......................................................................................................................76
6.6. Retouch Mode......................................................................................................................78
6.7. Hole Editor ...........................................................................................................................79
6.7.1. Upper Side of Hole Editor .....................................................................................80
6.7.2. Working Area........................................................................................................80
6.7.3. Preview.................................................................................................................81
6.7.4. Function Buttons...................................................................................................82
6.7.5. List of Hole/Slot.....................................................................................................88
6.7.6. Property of Hole/Slot.............................................................................................90
6.8. Job Editor.............................................................................................................................91
6.8.1. Layout Option .......................................................................................................91
6.8.2. Edging option........................................................................................................92
6.9. Edging Process....................................................................................................................93
6.9.1. Edging Start..........................................................................................................93
6.9.2. Edging Screen ......................................................................................................94
6.9.3. Edging Stop..........................................................................................................95
6.9.4. Edging Error .........................................................................................................96
6.9.5. Edging Finish........................................................................................................97
6.10. Frame Change .....................................................................................................................98
6.10.1. Frame Change Lens Registration .........................................................................98
6.10.2. Frame Change Mode............................................................................................99
6.10.3. Frame Change Procedure...................................................................................100
7. Configuration ...............................................................................................................................101
7.1. Configuration of Frame Reader ..........................................................................................101
7.2. Configuration of Edger .......................................................................................................102
7.2.1. Preferences ........................................................................................................103
7.2.2. Adjustments........................................................................................................111
8. System Maintenance....................................................................................................................126
8.1. Automatic Calibration of Frame Reader..............................................................................126
8.1.1. Stroke Calibration ...............................................................................................126
8.1.2. Frame Calibration ...............................................................................................126
8.1.3. Pattern Calibration ..............................................................................................127
8.2. Automatic Calibration of Edger...........................................................................................128
8.2.1. Size Calibration...................................................................................................128
8.2.2. Feeler Calibration ...............................................................................................128
8.3. Test Mode..........................................................................................................................129
8.3.1. Sensor ................................................................................................................129
8.3.2. X / Y / R ..............................................................................................................131
8.3.3. Feeler .................................................................................................................132

5
5
8.3.4. SBG / Wheel.......................................................................................................133
8.3.5. Pump..................................................................................................................134
8.3.6. Clamp / Window..................................................................................................135
8.3.7. Drill .....................................................................................................................136
8.3.8. PI / Motor............................................................................................................137
8.4. Wheel Dressing..................................................................................................................138
8.5. Statistics ............................................................................................................................139
8.5.1. Current Statistics ................................................................................................139
8.5.2. Wheel Statistics ..................................................................................................140
8.5.3. Total Statistics ....................................................................................................141
8.6. Date & Time.......................................................................................................................142
8.7. Touch Test.........................................................................................................................142
8.8. Configuration Management ................................................................................................143
8.9. SW Upgrade ......................................................................................................................144
8.10. Maintenance Code .............................................................................................................145
8.11. Maintenance Tips...............................................................................................................146
8.11.1. Wheel Replacement............................................................................................146
8.11.2. Drill Bit Replacement ..........................................................................................146
8.11.3. Regular Maintenance..........................................................................................148
8.11.4. Fuse Replacement..............................................................................................148
8.11.5. Cleaning .............................................................................................................149
9. Troubleshooting Guide................................................................................................................150
10. Specifications and Accessories..................................................................................................151
10.1. Standard Accessories ........................................................................................................151
10.2. Specifications.....................................................................................................................152
10.2.1. Specifications of Edger .......................................................................................152
10.2.2. Specifications of Frame Reader ..........................................................................152
10.2.3. Specifications of Blocker.....................................................................................152
10.3. Drawings of System ...........................................................................................................153
10.3.1. Drawings of Edger ..............................................................................................153
10.3.2. Drawings of Frame Reader.................................................................................154
10.3.3. Drawings of Blocker............................................................................................154
11. SERVICE INFORMATION..............................................................................................................155

6
6
HPE-810
HUVITZ
1. Introduction
1.1. Main Functions
This product is for processing lenses fit into eyeglasses frame, which automatically covers
from tracing to edging.
Edging
Material
Beveling
Flat
Edging
Grooving
Polishing
Safety
Beveling
Drilling
Plastic
○
○
○
○
○
○
Glass
○
○
X
X
○
X
High Index
○
○
○
○
○
○
Polycarbonate
○
○
○
○
○
○
Trivex®
○
○
○
○
○
○
High Resolution TFT-LCD (9.7”) and interface with touchscreen make it possible to use it
easily and process intuitively with the actual sized data (frame, PD, FPD etc.)
The “Digital Pattern Layout” modifies the lens shape in left/right, top/bottom as well as
circumference and optimizes the fitting challenge for Rimless and Semi-Rimless.
Frame Tracing, Layout and Lens Edging can be processed simultaneously. Frame Tracing
and Layout work can be saved in advance during the lens edging process.
Graphically Designed Test Mode enables you to effectively perform the routine
maintenance without the technical assistance.
It guarantees precise processing with its ability to scan every kind of frames from rimless to
goggles.
You can save the frame data in memory cards so that the processing can be restarted
anytime.
Hardware with durability and stability with effective processing algorithm makes the whole
processing easy and perfect.

7
7
1.2. System Configuration
Edger + Frame Reader + Manual Blocker
Edger (HPE-810)
Frame Reader (HFR-8000)
Blocker (HMB-8000)
Edger + Auto Blocker
Edger (HPE-810)
Auto Blocker (HAB-8000)

8
8
HPE-810
HUVITZ
NOTE
HPE-810 (ND) type does not support drilling function.
HPE-810 (ND) type is able to perform drilling by connecting an external drill machine
(HDM-8000) in the above system configuration.
Edger (HPE-810 (ND) type)
Driller (HDM-8000)
1.3. Classification
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Class A equipment
Class A equipment is intended for use in an industrial environment. In the documentation
for the user, a statement shall be included drawing attention to the fact that there may be
potential difficulties in ensuring electromagnetic compatibility in other environments, due to
conducted as well as radiated disturbances.
Protection against electric shock: Class I (when earthed)
Measurement Category: CAT II
Pollution Degree: 2

9
9
2. Safety Information
2.1. Introduction
Safety is everyone’s responsibility. The safe use of this machine is largely dependent upon the
installers, users, operators, and managers. It is prerequisite to read and understand these
specifications before installing, using, cleaning, fixing or revising. Fully understanding the whole
instructions must be the first priority. For this reason, the following safety notices have been placed
appropriately within the text of this manual to highlight safety related information or information
requiring special emphasis. All users, operators, and maintainers must be familiar with and pay
particular attention to all signs of Warnings and Cautions.
WARNING
“Warning” indicates the presence of a hazard that could result in severe personal injury, death or
substantial property damage if ignored.
CAUTION
“Caution” indicates the presence of a hazard that could result in minor injury, or property
damaged if ignored.-
NOTE
This is used to emphasize essential information.
Be sure to read this information to avoid operating the device incorrectly.
!
!

10
10
HPE-810
HUVITZ
2.2. Safety Symbols
The International Electrotechnical Commission (IEC) has established a set of symbols, which are
listed below.
This applies only to the instrument that has the certification symbol printed explicitly on the product
label or sticker.
I and O on power switch represent ON and OFF respectively.
This symbol identifies caution, risk of danger. Ensure you
understand the function of this control before using it. Control
function is described in the appropriate User’s or Service Manual.
Protective Earth Connection
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a
product it means the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will help prevent
potential negative consequences for the environment and
human health.
4. For more detailed information about disposal of your old
appliance, please contact your city office, waste disposal service
or the shop where you purchased the product.
Alternating Current