Hyd-Mech V18APC User manual

1
THANK YOU,
On behalf of everyone at HYD·MECH Group Limited, we would like to thank and congratulate you on your decision to
purchase a HYD·MECH bandsaw.
Your new machine is now ready to play a key role in increasing the e󰀩ciency of your operation, helping you to reduce cost
while boosting quality and productivity.
To ensure you are maximizing the power and versatility of your new HYD·MECH bandsaw, please take the time to
familiarize yourself and your employees with the correct operation and maintenance procedures as outlined in this
manual. Please keep this instruction manual for future reference in a known location and easily accessible to all users of
the device.
HYD·MECH o󰀨ers a great variety of options, components, and features for its various models. Therefore, some of the
equipment described in this manual (various illustrations and drawings) may not be applicable to your particular machine.
The information and specications provided in this manual were accurate at the time of printing. HYD·MECH reserves the
right to discontinue or change specications or design at any time without notice and without incurring any obligation.
Thank you.
Hyd·Mech Group Limited
P.O. Box 1659, 1079 Parkinson Road
Woodstock, Ontario, N4S 0A9
Phone : [phone]
Service : 1-877-237-0914
Sales : 1-877-276-SAWS (7297)
Fax : [phone]
e-mail : [email protected]
Printed MAY 2019
V18APC
393401

2

i
TABLE OF CONTENTS
SECTION 0 - SAFETY INSTRUCTIONS
SUMMARY .......................................................................................................................................0.1
BASIC RULES..................................................................................................................................0.3
RESPONSIBILITIES OF THE OWNER............................................................................................0.3
RESPONSIBILITIES OF THE OPERATOR AND MAINTENANCE PERSONNEL...........................0.4
SAFETY HAZARD LABELS .............................................................................................................0.6
SECTION 1 - INSTALLATION
SAFETY PRECAUTIONS.................................................................................................................1.1
V18 APC LIFTING AND SHIPPING..................................................................................................1.2
LEVELLING THE V18 APC ..............................................................................................................1.3
REMOVE HEAD RESTRAINTS .......................................................................................................1.4
INSTALLATION OF THE INFEED BASE..........................................................................................1.4
SHUTTLE GUARD INSTALLATION .................................................................................................1.8
HYDRAULIC OIL.............................................................................................................................1.11
CUTTING FLUID .............................................................................................................................1.11
WIRING CONNECTIONS................................................................................................................1.11
BLADE TENSION CHECK ..............................................................................................................1.12
EARTH GROUNDING PROCEDURE.............................................................................................1.12
SECTION 2 - OPERATING INSTRUCTIONS
INTERFACE OPERATION INSTRUCTIONS ...................................................................................2.1
PUSH BUTTON DESCRIPTIONS....................................................................................................2.2
CONTROL SYSTEM OPERATING INSTRUCTIONS ......................................................................2.4
MACHINE START UP.......................................................................................................................2.4
MANUAL MODE...............................................................................................................................2.5
KERF CORRECTION FOR ANGLE CUTTING (MANUAL MODE) ..................................................2.6
PARAMETERS .................................................................................................................................2.7
AUTOMATIC OPERATION..............................................................................................................2.10
PROCEDURE FOR EDITING OR STARTING A NEW JOB IN AUTO MODE SIMPLE SHAPES...2.10
HYDRAULIC FEED CONTROL.......................................................................................................2.14
CUTTING PARAMETERS CHART..................................................................................................2.14
CUTTING SOLIDS ..........................................................................................................................2.15
CUTTING STRUCTURALS.............................................................................................................2.15
ADDITIONAL CUTTING SETUP EXAMPLES.................................................................................2.19
COOLANT FLOW............................................................................................................................2.20
HEAD BACK LIMIT ADJUSTMENT.................................................................................................2.20
CHIP CONVEYOR ..........................................................................................................................2.20
HYDRAULIC CHIP CONVEYOR.....................................................................................................2.20
HEAD SWING BRAKE ....................................................................................................................2.21

ii
SECTION 3 - MAINTENANCE AND TROUBLE SHOOTING
BLADE CHANGE PROCEDURE .....................................................................................................3.2
BLADE REMOVAL............................................................................................................................3.2
BLADE INSTALLATION....................................................................................................................3.3
BLADE TRACKING ..........................................................................................................................3.3
DRIVE WHEEL ADJUSTMENT........................................................................................................3.3
IDLER WHEEL ADJUSTMENT ........................................................................................................3.4
BLADE BRUSH ADJUSTMENT .......................................................................................................3.4
BLADE GUIDES...............................................................................................................................3.4
HEAD FORWARD LIMIT SETTING .................................................................................................3.5
GEARBOX LUBRICATION (V18 WITH A412 GEARBOX)...............................................................3.5
LUBRICATION..................................................................................................................................3.5
HYDRAULIC MAINTENANCE..........................................................................................................3.7
TROUBLE SHOOTING GUIDE........................................................................................................3.8
V18 APC ELECTRICAL...................................................................................................................4.1
SECTION 4 - ELECTRICAL
FOR ELEC SCHEMATICS AND COMPONENTS PARTS LIST SEE PDF ON ATTACHED CD ......4.8
SECTION 5 - HYDRAULIC SYSTEM
HYDRAULIC PARTS LIST................................................................................................................5.1
GLAND ASSEMBLIES......................................................................................................................5.2
PISTON ASSEMBLIES.....................................................................................................................5.2
HYDRAULIC SCHEMATIC AND PLUMBING DIAGRAM:................................................................5.3
SEE PDF ON ATTACHED CD..........................................................................................................5.3
SECTION 6 - MECHANICAL ASSEMBLIES
MECHANICAL ASSEMBLY DRAWINGS & PARTS LIST: SEE PDF ON ATTACHED CD................6.1
SECTION 7 - OPTIONS
OPTIONAL ASSEMBLY DRAWINGS: SEE PDF ON ATTACHED CD .............................................7.1
SECTION 8 - SPECIFICATIONS
V18APC SPECIFICATIONS .............................................................................................................8.1
V18APC LAYOUT LH (CANTED HEAD)..........................................................................................8.2
V18APC LAYOUT RH (CANTED HEAD) .........................................................................................8.4
SECTION 9 - WARRANTY
WARRANTY .....................................................................................................................................9.1

0.1
SECTION 0 - SAFETY INSTRUCTIONS
SUMMARY
All persons operating this machine must have read and understood all of the following sections of this Manual:
Section 0 SAFETY
Section 2 OPERATING INSTRUCTIONS
However, as a memory aid, the following is a summary of the Safety Section.
Put Safety First
Mandatory Information – What operators and maintenance people must have read and understood.
Signatures – Everyone involved with this machine must sign to conrm they have read and understood mandatory
information.
Basic Rules – only use this machine when
• It is in good working order.
• All safety equipment is in place and functional.
• Operations are in compliance with this manual.
• Materials are within designed specications and are non-hazardous.
Owner is responsible to
• Keep Manual accessible at the machine.
• Ensure only reliable, fully trained personnel work with the machine.
• Clearly dene responsibilities of all personnel working with the machine.
• Keep the machine in good working order.
Operator and Maintenance Personnel are responsible to:
• Keep all safety equipment in order, check its function at the beginning of each shift, and report any shortcomings.
• Shut down machine and report any faults or malfunctions that could impair safety.
• Understand and obey safety hazard labels.
• Not to wear un-restrained long hair, loose clothing or jewellery.
• Wear all required personal protective equipment.
• Not to wear gloves within 24 inches of moving blade.
• Maintain a clean working area and machine.
• Always use Lock-out when performing maintenance or repairs.

0.2
FOREWORD
Put Safety First!
This Safety Section contains important information to help you work safely with your machine and describes the dangers
inherent to bandsaws. Some of these dangers are obvious, while others are less evident.
It really is important to PUT SAFETY FIRST. Make it a habit to consider the hazards associated with any action BEFORE
you do it. If you feel any uncertainty, stop and nd a safer approach to the action. If you’re still uncertain, ask for advice
from your supervisor.
The SAFETY FIRST approach is particularly necessary when you do something new, or di󰀨erent, and most people
instinctively recognize this, although impatience may still cause them to take unnecessary risks.
Danger also lurks in the routine task that we have done over and over. Here, familiarity, boredom, or tiredness may lull us
into unthinking, automatic repetition. Be alert for this, and when you feel it happening, stop and assess your
situation. Review the safety hazards associated with what you are doing. That should get your brain working again.
Certainly production is important, but if you think you’re too busy to put safety rst, think how much production you’ll lose if
you get hurt.
You owe it to yourself, your family, and your co-workers to PUT SAFETY FIRST.
Mandatory Information
All persons operating this machine must have read and understood all of the following sections of this Manual:
Section 0 SAFETY
Section 2 OPERATING INSTRUCTIONS
Personnel involved in installation and maintenance of the machine must have read and understood all sections of the
manual
Persons who have di󰀩culty reading, or for whom English is not their rst language, must receive particularly thorough
instruction.
Signatures
Everyone involved in operation of this machine must sign below to conrm that:
I have read and understood all parts of Section 0 – Safety, and Section 2 – Operating Instructions.
Name Date Signature
Everyone involved in the installation, inspection, maintenance, and repair of this machine must sign below to conrm that:
I have read and understood all parts of this Operation and Maintenance Manual.
Name Date Signature

0.3
BASIC RULES
Intended Use
Our machines are designed and built in line with the state of the art, and specically in accordance with
American National Standards Institute Standard B11.10 Safety Requirements for Metal Sawing Machines.
However, all machines may endanger the safety of their users and/or third parties, and be damaged,
or damage other property, if they are operated incorrectly, used beyond their specied capacity, or for
purposes other than those specied in this Manual.
Exclusion of Misuse
Misuse includes, for example:
Sawing hazardous materials such as magnesium or lead.
Sawing work pieces which exceed the maximum workload appearing in the Specications.
Operating the machine without all original safety equipment and guards.
Liability
The machine may only be operated:
When it is in good working order, and
When the operator has read and understood the Safety and Operating Instructions Sections of the
Manual, and
When all operations and procedures are in compliance with this Manual.
Hyd-Mech Group cannot accept any liability for personal injury or property damage due to operator errors
or non-compliance with the Safety and Operating Instructions contained in this Manual.
RESPONSIBILITIES OF THE OWNER
Organization of work
This Operation and Maintenance Manual must always be kept near the machine so that it is accessible to
all concerned.
The general, statutory and other legal regulations on accident prevention and environmental protection
must also be observed, in addition to the Manual material. The operators and maintenance personnel
must be instructed accordingly. This obligation also includes the handling of dangerous substances and
the provision and use of personal protective equipment.
Choice and qualication of personnel
Ensure that work on the machine is only carried out by reliable persons who have been appropriately
trained for such work.
Training
Everyone working on or with the machine must be properly trained with regard to the correct use of the
machine, the correct use of safety equipment, the foreseeable dangers that may arise during operation of
the machine, and the safety precautions to be taken.
In addition, the personnel must be instructed to check all safety devices at regular intervals.

0.4
Dene responsibilities
Clearly dene exactly who is responsible for operating, setting-up, servicing and repairing the machine.
Dene the responsibilities of the machine operator and authorize him to refuse any instructions by third
parties if they run contrary to the machine’s safety.
Persons being trained on the machine may only work on or with the machine under the constant
supervision of an experienced operator. Observe the minimum age limits required by law.
Condition of Machine and Workplace
Ensure that the machine and its safety equipment are kept in good working order.
Ensure that the work area is well lit, and protected from the elements, such as rain, snow, abrasive dust,
and extremes of temperature.
Ensure that the machine is installed with su󰀩cient clearance around it for the safe loading and unloading
of work pieces.
RESPONSIBILITIES OF THE OPERATOR AND MAINTENANCE PERSONNEL
Safety equipment
All machines are delivered with safety equipment that must not be removed or bypassed during operation.
The correct functioning of safety equipment on the machine must be checked:
• At the start of every shift.
• After maintenance and repair work
• When starting for the rst time, and after prolonged shutdowns
Emergency Stop Button (E-Stops)
Always be aware of the location of the Emergency Stop Button(s). Do not allow material or objects to
block your access to an Emergency Stop.
Damage
If any changes capable of impairing safety are observed in the machine or its operation, such as damage,
malfunctions, or irregularities, then appropriate steps must be taken immediately, the machine switched
o󰀨, locked-out, and the fault reported to the responsible person.
Safe operation
The machine may only be operated when in good working order and when all protective equipment is in
place and operational.
Keep a safe distance from all moving parts – especially the blade and vises.
Stock should not be loaded onto the saw if the blade is running.
Long and heavy stock should always be properly supported in front of and behind the saw.
Faults
The machine must be switched o󰀨 and locked-out before starting to remedy any faults.
Safety hazard labels
Safety hazard labels and other instructional labels on the machine must be observed. They must be
clearly visible and legible at all times. If they become damaged they must be replaced.

0.5
Clothing, jewellery, protective equipment
Personnel operating or working on the machine must not wear un-restrained long hair, loose-tting
clothes and dangling jewellery.
When operating or working on the machine, always wear suitable, o󰀩cially tested personal protective
equipment such as safety glasses and safety boots and any other equipment required by workplace
regulations.
Gloves
Experience has shown that careless use of gloves around machinery is a major factor in serious
hand injuries.
Gloves should not be worn when operating or adjusting the machine, except:
Wear protective gloves when handling bandsaw blades at blade changes.
Gloves may be worn when handling work pieces, only if the machine is in Manual Mode
and the bandsaw blade is not running.
If the machine is running in Auto Mode, and only if the cut parts are greater than 24
inches long, it may be possible to safely wear gloves for handling the cut parts, but the
wearer of the gloves must never put his hands near the blade for any reason. If the cut
parts are less than 24 inches long, it is required to arrange their automatic ow into a
parts bucket or other suitable arrangement to avoid the necessity to pick them o󰀨 the
machine by hand.
Hearing protection
Ear protection must be worn whenever necessary.
The level and duration of noise emission requiring hearing protection depends upon the national
regulations in the country in which the machine is being used.
The actual level of noise emission by band sawing machines depends upon work piece size, shape and
material, blade type, blade speed and feed rate.
The only practical course of action is to measure the actual noise emission levels for the type of work that
is typically done. With reference to national standards, decide upon the necessary hearing protection
required.
In the absence of such measurements, it is advisable for anyone exposed to long periods of moderate to
loud noise to wear hearing protection. It is important to understand that hearing loss is gradual and easily
goes un-noticed until it is serious and irreversible.
Workplace
A clear working area without any obstructions is essential for safe operation of the machine. The
oor must be level and clean, without any build-up of chips, o󰀨-cuts, coolant, or hydraulic oil.
The workplace must be well lit, and protected from the elements, such as rain, snow, abrasive dust, and
extremes of temperature
Nothing may ever be placed on, or leaned against the machine, with the obvious exception of the work
piece on the table and conveyor of the machine.
Master Disconnect
Lock-out the machine before undertaking any maintenance or repair work on it. ‘Lock-out’ refers switching
o󰀨 the master electrical disconnect switch, and locking it out so that it cannot be switched on again
without authorization.

0.6
On Hyd-Mech machines the Master Disconnect Switch will be of one of four types:
• Rotary switch mounted in electrical control cabinet door and inter-locked with door.
• Rotary switch mounted on the side of the operator interface console.
• Lever switch mounted in separate box on the machine.
• Supply disconnect switch supplied by user at installation and usually wall-mounted within sight of
the machine, depending upon local regulations.
In almost all jurisdictions, it is required that owners of industrial equipment establish and post
lock-out procedures. Know and use the lock-out procedures of your company or organization.
Residual Risks
The machine is still not completely de-energized if an electrical cabinet door type switch is
locked-out.
The line side of the disconnect switch itself remains energized.
Variable speed blade drives store dangerous voltage in their capacitors, and this requires time to
dissipate. After locking out power, wait 3 minutes before beginning to work on machine electrical
circuits.
If compressed air is supplied to the machine to power a mist lubrication system or other devices,
it should be disconnected, and any stored air pressure released before working on the machine.
The weight of individual machine components represents stored potential energy that can be
released if they fall when disconnected. Secure these components with adequate hoisting gear
before disassembly.
SAFETY HAZARD LABELS
The safety hazard labels attached to your machine represent important safety information to help you avoid personal injury
or death.
All supervisors, operators, and maintenance personnel must locate and understand the safety information associated with
each hazard label prior to operating or servicing the machine.
The safety hazard labels shown below are located at various positions on the machine to indicate possible safety hazards.
The location and re-order part number of all the safety labels associated with this particular model of bandsaw are indicated
at the end of this section of the manual. It is important to replace any safety hazard label that becomes damaged or illegible.
HAZARDOUS VOLTAGE INSIDE
Contact with high voltage may cause death or serious injury. Never perform
maintenance on, or near, electrical components until the machine’s electrical
power source has been disconnected. Lock-out power in accordance with your
company’s lock-out procedures before any such maintenance. The “Stop” or
“Emergency Stop” push button does not disconnect the machine’s power supply.
Hazardous voltage is still present in the machines electrical circuits.
The machine’s Electrical Disconnect Switch does disconnect voltage from the
machine’s circuits; however hazardous voltage is still present inside the main
electrical cabinet, on the infeed (line) side of the main fuses. Therefore keep hands
and tools away from the infeed side of the control panel main fuses. If these fuses need to be replaced, use a fuse puller.
Allow three minutes after locking-out power before opening any electrical enclosures. Your machine may be equipped with a
variable frequency drive that stores high voltage within its capacitors. Three minutes will allow su󰀩cient time for this voltage
to safely discharge.
Never spray coolant directly at electrical components or cabinets.

0.7
MOVING BANDSAW BLADE WILL CUT
Do NOT operate with guard removed.
Do NOT place hands or ngers near moving bandsaw blade.
For blade changing, always follow the proper Blade Changing Procedure, as given in
Section 3 of this manual.
PINCH POINT
Machine parts may move without warning, either because the machine is operating automatically, or because another
person initiates the motion. Keep hands clear of all labelled pinch points, whenever the machine is running. Machine
vises can exert great force and cause severe injury. Keep hands clear of vises and work piece when vises are opened or
closed. Be aware that vise closing or opening may result in potentially dangerous work piece movement. Be aware also
that the opening motion of a vise may create potential pinch points.
MOVING PARTS CAN CRUSH AND CUT
Keep hands clear of chip auger. Lock-out power in accordance with your com-
pany’s lock-out procedures before attempting to clear a jam in the chip auger.
Be aware that the chip auger may start unexpectedly, either because the
machine is operating automatically, or because another person initiates the
motion.
If the chip auger is stalled because of a jam, it may start without warning when
the jam is cleared, unless the machine power is locked out.

1.1
SECTION 1 - INSTALLATION
SAFETY PRECAUTIONS
All safety precautions must be observed during installation, operation, or repair work on the V18 APC bandsaw machine.
Inspect the machine thoroughly before power hook-up. Pay special attention to the electrical and hydraulic systems to
ensure no damage was caused in shipping.
Power hook-up should be performed by qualied personnel.
If not performing properly, the machine should be stopped immediately and set-up, or repaired by a qualied person.
Stock must not be loaded while the blade is running and the V18 APC should not be operated unless all guards, covers,
and doors are in place and closed.
Long and heavy stock should be supported where it extends o󰀨 the saw table.
The operator should keep a safe distance from all moving parts especially the blade and operating vises.
Long hair, loose clothing, or gloves, should not be worn while operating the V18 APC.
The area around the machine should be kept clean and tidy.
The V18 APC machine should be used according to its specications.
The operator must wear eye protection.
No modications to the machine are allowed without Hyd·Mech Group Limited’s prior approval. Any approved
modications shall be performed by trained personnel.

1.2
V18 APC LIFTING AND SHIPPING
The shipping weight of the V18 APC main machine is 6000 lb. The machine can be lifted from the infeed side of the ma-
chine by forklift as shown below.
NOTE: The head restraint plate attached to the head and table must be removed before machine start up.

1.3
A machinists level being used in both directions
LEVELLING THE V18 APC
It is important that the V18 APC be leveled and provision is made to secure the saw with concrete anchors to the oor.
See foundation plan below - Note: There are 2 levelling bolts inside of the power pack compartment.
Using a machinist’s level, level the saw from side to side and from front to back.
AA
0
1.0
22.8
54.7
72.5
90.5
82.1
102.2
.0 3.5
73.4
70.5
6.5
5.7
45.5
46.0
80.2 85.0
B
SECTION A-A
FOUNDATION/MOUNTING LAYOUT
3.00
6.00
1.25
.75 THRU ALL
.66 THRU ALL
3/4-10 UNC THRU ALL
DETAIL B
SCALE 1 : 8
THE DATA/DESIGN CONTAINED HEREIN IS PROPRIETARY
AND CONFIDENTIAL.REPRODUCTION,PUBLICATION OR
DISTRIBUTION OF ANY PART REQUIRES WRITTEN CONSENT
OF HYD-MECH GROUP.THIS DATA IS THE PROPERTY OF
HYD MECH GROUP AND ITS POSSESION CONFERS NO
LICENSE TO USE OR RIGHT OR LICENSE TO DISCLOSE IT
TO OTHERS FOR ANY PURPOSE WHATSOEVER.
ALL RIGHTS RESERVED.
A
0
B
C
D
E
G F
H
I
J K L
M
2
1
4
3
5
8
7
6
2
1
4
3
5
8
7
6
G
F
E
D
C
B
A
H
I
J
K
L M
0
SCALE
SHEET
REV
DRAWING NUMBER:
WOODSTOCK. ONTARIO. CANADA N4S 0A9
HYDMECH GROUP LIMITED
50002585
1:20
5
OF
5
-
AA
0
1.0
22.8
54.7
72.5
90.5
82.1
102.2
.0 3.5 73.4
70.5
6.5
5.7
45.5
46.0
80.2 85.0
B
SECTION A-A
FOUNDATION/MOUNTING LAYOUT
3.00
6.00
1.25
.75 THRU ALL
.66 THRU ALL
3/4-10 UNC THRU ALL
DETAIL B
SCALE 1 : 8
THE DATA/DESIGN CONTAINED HEREIN IS PROPRIETARY
AND CONFIDENTIAL.REPRODUCTION,PUBLICATION OR
DISTRIBUTION OF ANY PART REQUIRES WRITTEN CONSENT
OF HYD-MECH GROUP.THIS DATA IS THE PROPERTY OF
HYD MECH GROUP AND ITS POSSESION CONFERS NO
LICENSE TO USE OR RIGHT OR LICENSE TO DISCLOSE IT
TO OTHERS FOR ANY PURPOSE WHATSOEVER.
ALL RIGHTS RESERVED.
A
0
B
C
D
E
G F
H
I
J K L
M
2
1
4
3
5
8
7
6
2
1
4
3
5
8
7
6
G
F
E
D
C
B
A
H
I
J
K
L M
0
SCALE
SHEET
REV
DRAWING NUMBER:
WOODSTOCK. ONTARIO. CANADA N4S 0A9
HYDMECH GROUP LIMITED
50002585
1:20
5
OF
5
-
Left Hand Infeed Conguration

1.4
REMOVE HEAD RESTRAINTS
Before start-up, remove the head support strut installed for shipping purposes to secure the head to the base. Replace the
two 5/16 NC countersunk screws which fasten the wear-strip down.
INSTALLATION OF THE INFEED BASE
The shipping weight of the infeed is 3000 lb. The infeed can be lifted from the datum side by forklift as shown below.

1.5
• Move the infeed base into position under the wear plate and line up the holes for the roll pins.
Wear Plate
Roll Pins
• Install the coolant side shields to both the infeed and outfeed side of the base.

1.6
Tighten SHCS
• Use the leveling foot bolts to raise the infeed base towards the wear plate. Tighten the four socket head cap screws
(390715) to mate the two pieces together. Level the infeed base with the machine by elevating the rear adjusting bolt.
Once level has been achieved make sure that all levelling bolts are touching the oor.
• Remove the infeed base cover. Feed the bundle of hydraulic hosed and electrical cables from inside the machine to
the infeed base

1.7
• Plumb the hydraulic hoses as per the photo below. Refer to the “Hydraulic Plumbing Diagram” found in the DWG
package CD
NOTE: LH Infeed conguration shown
91B
101A
61E
91C
62E
102A
92C
93
101
61B
91
62B
102
92
92B 92D
• Fasten the conduit to the bracket with the provided nut.
Connect the M12 connectors:
C 19 : C 19-1
C2 23 : C 23
C E1 : C E2

1.8
SHUTTLE GUARD INSTALLATION
• Refer to the “Perimeter Guard Assembly” drawings in the DWG package CD
• Assemble the moveable side leg to the infeed assembly
• Assemble the datum side leg to the infeed assembly

1.9
• Assemble the rear guard tubes to the back of the infeed assembly
• Assemble both the front guard and the hinged guard to the legs. A pulley is mounted on a bracket and attached to
each rear corner of the safety guard. Fasten the three sides of the guard together at these brackets.
Adjust the levelling bolts on each leg to ensure the guard is level.
• Remove the cover of the trip wire control box.