Hyd-Mech H14A User manual

01
H-14A
April 2005, Rev B
393301
THANK YOU,
On behalf of everyone at HYD.MECH, I would like to thank and congratulate you on your decision to purchase
a HYD.MECH band saw.
Your new machine is now ready to play a key role in increasing the efciency of your operation, helping you to
reduce cutting costs while boosting quality and productivity.
To ensure you are maximizing the power and versatility of your new HYD.MECH band saw, please take the
time to familiarize yourself and your employees with the correct operation and maintenance procedures as
outlined in this manual.
We sincerely appreciate the condence you have demonstrated in purchasing our product and look forward to
building a long and mutually benecial relationship.
Thank-you.
HYD.MECH GROUP LIMITED
P.O. BOX 1030, 1079 Parkinson Road
Woodstock, Ontario Canada, N4S 8A4
Phone: [phone]
Service 1-877-237-0914
Sales 1-877-276-SAWS(7297)
Fax [phone]
e-mail, [email protected]

TOC.1
TABLE OF CONTENTS
SECTION 0 - SAFETY INSTRUCTIONS
SUMMARY ..................................................................................................................................................................0.1
FOREWORD ...............................................................................................................................................................0.2
RESPONSIBILITIES OF THE OWNER.......................................................................................................................0.5
RESPONSIBILITIES OF THE OPERATOR AND MAINTENANCE PERSONNEL......................................................0.6
SECTION 1 – INSTALLATION
SAFETY PRECAUTIONS............................................................................................................................................1.1
LIFTING AND SHIPPING ............................................................................................................................................1.2
FOUNDATION LEVELING AND ANCHORING ...........................................................................................................1.2
EARTH GROUNDING PROCEDURE.........................................................................................................................1.2
WIRING CONNECTIONS............................................................................................................................................1.3
HYDRAULIC OIL AND CUTTING FLUID ....................................................................................................................1.3
SECTION 2 - OPERATING INSTRUCTIONS
BLADE BASICS ..........................................................................................................................................................2.1
VARIABLE SPEED CONTROL ...................................................................................................................................2.1
THE CONTROL PANEL ..............................................................................................................................................2.1
MANUAL OPERATION................................................................................................................................................2.2
PLC 100 CONTROL SYSTEM ....................................................................................................................................2.3
ACTIVATING THE PLC ...............................................................................................................................................2.4
FUNCTION KEY DESCRIPTIONS..............................................................................................................................2.4
SINGLE PART CYCLE OPERATION ..........................................................................................................................2.6
KERF CORRECTION..................................................................................................................................................2.6
AUTOMATIC OPERATION..........................................................................................................................................2.7
PROCEDURE FOR EDITING OR STARTING A NEW JOB IN AUTO MODE.............................................................2.7
WORKING WITH A QUEUE ........................................................................................................................................2.8
CUTTING PARAMETERS CHART..............................................................................................................................2.9
CUTTING STRUCTURALS.........................................................................................................................................2.10
COOLANT FLOW........................................................................................................................................................2.14
HEAD UP AND DOWN LIMIT SETTING .....................................................................................................................2.15
SECTION 3 - MAINTENANCE & TROUBLESHOOTING
BLADE CHANGING PROCEDURE ............................................................................................................................3.1
BLADE TRACKING AND ADJUSTMENT....................................................................................................................3.1
BLADE GUIDE ADJUSTMENT ...................................................................................................................................3.3
BLADE BRUSH ADJUSTMENT ..................................................................................................................................3.3
CAM FOLLOWER ADJUSTMENT ..............................................................................................................................3.3
LUBRICATION.............................................................................................................................................................3.3
HYDRAULIC MAINTENANCE.....................................................................................................................................3.3
CLEANLINESS............................................................................................................................................................3.5
TROUBLESHOOTING ................................................................................................................................................3.6
PROGRAMMABLE LOGIC CONTROL, MITSUBISHI 100 .........................................................................................3.7
PLC 100 TROUBLESHOOTING .................................................................................................................................3.9
SECTION 4 - ELECTRICAL SYSTEM
GENERAL INFORMATION..........................................................................................................................................4.1
INITIAL START-UP ......................................................................................................................................................4.1
LIST OF H14A ELECTRICAL COMPONENTS ..........................................................................................................4.2
H14 POWER COMPONENTS FOR SPECIFIC VOLTAGES ......................................................................................4.4
ELECTRICAL SCHEMATICS ......................................................................................................................................4.6
SECTION 5 - HYDRAULIC SYSTEM
GLAND ASSEMBLIES ................................................................................................................................................5.2
PISTON ASSEMBLIES................................................................................................................................................5.2

TOC.2
HYDRAULIC SCHEMATIC..........................................................................................................................................5.3
HYDRAULIC PLUMBING DIAGRAM ..........................................................................................................................5.4
SECTION 6 - MECHANICAL ASSEMBLIES
BLADE BRUSH ASSEMBLY .......................................................................................................................................6.1
GUIDE ARM ASSEMBLY ............................................................................................................................................6.2
HYDRAULIC CARBIDE GUIDE ASSEMBLY ..............................................................................................................6.3
BLADE TENSIONER ASSEMBLY...............................................................................................................................6.4
HYDRAULIC TANK ASSEMBLY..................................................................................................................................6.5
HYDRAULIC PUMP ASSEMBLY ................................................................................................................................6.6
CHIP AUGER ASSEMBLY ..........................................................................................................................................6.7
FRONT VISE ASSEMBLY ...........................................................................................................................................6.8
CONVEYOR ASSEMBLY ............................................................................................................................................6.10
SHUTTLE VISE ASSEMBLY .......................................................................................................................................6.11
DATUM JAW ASSEMBLY............................................................................................................................................6.12
BONFIGLIOLI A412 GEARBOX ASSEMBLY .............................................................................................................. 6.14
REYNOLDS PM40 GEARBOX ASSEMBLY................................................................................................................6.16
SECTION 7 - OPTIONAL EQUIPMENT
BUNDLING ASSEMBLY ..............................................................................................................................................7.1
VERTICAL ROLLERS .................................................................................................................................................7.2
OUT OF STOCK ASSEMBLY......................................................................................................................................7.3
VARIABLE VISE PRESSURE .....................................................................................................................................7.3
SECTION 8 - SPECIFICATIONS
H-14A LAYOUT DRAWING .........................................................................................................................................8.2
WARRANTY................................................................................................................................................................9.1
PLC PARAMETERS ...................................................................................................................................................9.2

0.1
SECTION 0 - SAFETY INSTRUCTIONS
SUMMARY
All persons operating this machine must have read and understood all of the following sections of this Manual:
Section 0 SAFETY
Section 2 OPERATING INSTRUCTIONS
However, as a memory aid, the following is a summary of the Safety Section.
Put Safety First
Mandatory Information – What operators and maintenance people must have read and understood.
Signatures – Everyone involved with this machine must sign to conrm they have read and understood mandatory infor-
mation.
Basic Rules – only use this machine when
• it is in good working order
• all safety equipment is in place and functional
• operations are in compliance with this manual
• materials are within designed specications and are non-hazardous
Owner is responsible to
• keep Manual accessible at the machine
• ensure only reliable, fully trained personnel work with the machine
• clearly dene responsibilities of all personnel working with the machine
• keep the machine in good working order
Operator and Maintenance Personnel are responsible to:
• keep all safety equipment in order, check its function at the beginning of each shift, and report any shortcomings
• shut-down machine and report any faults or malfunctions which could impair safety
• understand and obey safety hazard labels
• not to wear un-restrained long hair, loose clothing or jewellery
• wear all required personal protective equipment
• not to wear gloves within 24 inches of moving blade
• maintain a clean working area and machine
• always use Lock-out when performing maintenance or repairs.

0.2
0.3
FOREWORD
Put Safety First!
This Safety Section contains important information to help you work safely with your machine and describes the dangers
inherent in our machines. Some of these dangers are obvious, while others are less evident.
It really is important to PUT SAFETY FIRST. Make it a habit to consider the hazards associated with any action BEFORE
you do it. If you feel any uncertainty, stop and nd a safer approach to the action. If you’re still uncertain, ask for advice
from your supervisor.
The SAFETY FIRST approach is particularly necessary when you do something new, or different, and most people in-
stinctively recognize this, although impatience may still cause them to take unnecessary risks.
Danger also lurks in the routine task that we have done over and over. Here, familiarity, boredom, or tiredness may lull us
into unthinking, automatic repetition. Be alert for this, and when you feel it happening, stop and take stock of your situa-
tion. Review the safety hazards associated with what you are doing. That should get your brain working again.
Certainly production is important, but if you think you’re too busy to put safety rst, think how much production you’ll lose if
you get hurt.
You owe it to yourself, your family, and your co-workers to PUT SAFETY FIRST.
Mandatory Information
All persons operating this machine must have read and understood all of the following sections of this Manual:
Section 0 SAFETY
Section 2 OPERATING INSTRUCTIONS
Personnel involved in installation and maintenance of the machine must have read and understood all sections of the
manual
Persons who have difculty reading, or for whom English is not their rst language, must receive particularly thorough
instruction.

0.2
0.3
Signatures
Everyone involved in operation of this machine must sign below to conrm that:
I have read and understood all parts of Section 0 – Safety, and Section 2 – Operating Instructions.
Name Date Signature
Everyone involved in the installation, inspection, maintenance, and repair of this machine must sign below to conrm that:
I have read and understood all parts of this Operation and Maintenance Manual.
Name Date Signature
BASIC RULES
Intended Use
Our machines are designed and built in line with the state of the art, and specically in accordance with
American National Standards Institute Standard B11.10 Safety Requirements for Metal Sawing Machines.
However, all machines may endanger the safety of their users and/or third parties, and be damaged,
or damage other property, if they are operated incorrectly, used beyond their specied capacity, or for
purposes other than those specied in this Manual.

0.4
0.5
Exclusion of Misuse
Misuse includes, for example:
Sawing hazardous materials such as magnesium or lead
Sawing work pieces which exceed the maximum workload appearing in the Specications
Operating the machine without all original safety equipment and guards
Liability
The machine may only be operated:
when it is in good working order, and
when the operator has read and understood the Safety and Operating Instructions Sections of the Manu-
al, and
when all operations and procedures are in compliance with this Manual.
Hyd-Mech Group cannot accept any liability for personal injury or property damage due to operator errors
or non-compliance with the Safety and Operating Instructions contained in this Manual.

0.4
0.5
RESPONSIBILITIES OF THE OWNER
Organization of work
This Operation and Maintenance Manual must always be kept near the machine so that it is accessible to
all concerned.
The general, statutory and other legal regulations on accident prevention and environmental protection
must also be observed, in addition to the Manual material. The operators and maintenance personnel
must be instructed accordingly. This obligation also includes the handling of dangerous substances and
the provision and use of personal protective equipment.
Choice and qualication of personnel
Ensure that work on the machine is only carried out by reliable persons who have been appropriately
trained for such work.
Training
Everyone working on or with the machine must be duly trained with regard to the correct use of the ma-
chine, the correct use of safety equipment, the foreseeable dangers that may arise during operation of the
machine, and the safety precautions to be taken.
In addition, the personnel must be instructed to check all safety devices at regular intervals.
Dene responsibilities
Clearly dene exactly who is responsible for operating, setting-up, servicing and repairing the machine.
Dene the responsibilities of the machine operator and authorize him to refuse any instructions by third
parties if they run contrary to the machine’s safety.
Persons being trained on the machine may only work on or with the machine under the constant supervi-
sion of an experienced operator. Observe the minimum age limits required by law.

0.6
0.7
Condition of Machine and Workplace
Ensure that the machine and its safety equipment is kept in good working order.
Ensure that the work area is well lit, and protected from the elements, such as rain, snow, abrasive dust,
and extremes of temperature.
Ensure that the machine is installed with sufcient clearance around it for the safe loading and unloading
of work pieces.
RESPONSIBILITIES OF THE OPERATOR AND MAINTENANCE PERSONNEL
Safety equipment
All machines are delivered with safety equipment that must not be removed or bypassed during operation.
The correct functioning of safety equipment on the machine must be checked:
• at the start of every shift.
• after maintenance and repair work
• when starting for the rst time, and after prolonged shutdowns
Emergency Stop Button ( E-Stops)
Always be aware of the location of the Emergency Stop Button(s). Do not allow material or objects to
block your access to an Emergency Stop.
Damage
If any changes capable of impairing safety are observed in the machine or its operation, such as damage,
malfunctions, or irregularities, then appropriate steps must be taken immediately, the machine switched
off, locked-out, and the fault reported to the responsible person.
Safe operation
The machine may only be operated when in good working order and when all protective equipment is in
place and operational.
Keep a safe distance from all moving parts – especially the blade and vises
Stock should not be loaded onto the saw if the blade is running
Long and heavy stock should always be properly supported in front of and behind the saw.
Faults
The machine must be switched off and locked-out before starting to remedy any faults.
Safety hazard labels
Safety hazard labels, and other instructional labels on the machine must be observed. They must be
clearly visible and legible at all times. If they become damaged they must be replaced.
Clothing, jewellery, protective equipment
Personnel operating or working on the machine must not wear un-restrained long hair, loose-

0.6
0.7
tting clothes and dangling jewellery.
When operating or working on the machine, always wear suitable, ofcially tested personal pro-
tective equipment such as safety glasses and safety boots and any other equipment required by
plant regulations.
Gloves
Experience has shown that careless use of gloves around machinery is a major factor in serious
hand injuries.
Gloves should not be worn when operating or adjusting the machine, except:
Wear protective gloves when handling bandsaw blades at blade changes.
Gloves may be worn when handling work pieces, only if the machine is in Manual Mode
and the bandsaw blade is not running.
If the machine is running in Auto Mode, and only if the cut parts are greater than 24
inches long, it may be possible to safely wear gloves for handling the cut parts, but the
wearer of the gloves must never put his hands near the blade for any reason. If the cut
parts are less than 24 inches long, it is required to arrange their automatic ow into a
parts bucket or other suitable arrangement to avoid the necessity to pick them off the
machine by hand.
Hearing protection
Ear protection must be worn whenever necessary.
The level and duration of noise emission requiring hearing protection depends upon the national
regulations in the country in which the machine is being used.
The actual level of noise emission by band sawing machines depends upon work piece size,
shape and material, blade type, blade speed and feed rate.
The only practical course of action is to measure the actual noise emission levels for the type
of work that is typically done. With reference to national standards, decide upon the necessary
hearing protection required.
In the absence of such measurements, it is advisable for anyone exposed to long periods of
moderate to loud noise to wear hearing protection. It is important to understand that hearing loss
is gradual and easily goes un-noticed until it is serious and irreversible.
Workplace
A clear working area without any obstructions is essential for safe operation of the machine. The oor
must be level and clean, without any build-up of chips, off-cuts, coolant, or hydraulic oil.
The workplace must be well lit, and protected from the elements, such as rain, snow, abrasive dust, and
extremes of temperature
Nothing may ever be placed on, or leaned against the machine, with the obvious exception of the work
piece on the table and conveyor of the machine.
Master Disconnect
Lock-out the machine before undertaking any maintenance or repair work on it. ‘Lock-out’ refers switching
off the master electrical disconnect switch, and locking it out so that it cannot be switched on again
without authorization.
On Hyd-Mech machines the Master Disconnect Switch will be of one of three types:
• Rotary switch mounted in electrical control cabinet door and inter-locked with door

0.8
• Lever switch mounted in separate box mounted on the machine
• Supply disconnect switch supplied by user at installation and usually wall-mounted within sight of
the machine, depending upon local regulations.
In almost all jurisdictions, it is required that owners of industrial equipment establish and post lock-out pro-
cedures. Know and use the lock-out procedures of your company or organization.
Residual Risks
The machine is still not completely de-energized if an electrical cabinet door type switch is
locked-out.
The line side of the disconnect switch itself remains energized.
Variable speed blade drives store dangerous voltage in their capacitors, and this requires time to
dissipate. After locking out power, wait 3 minutes before beginning to work on machine electrical
circuits.
If compressed air is supplied to the machine to power a mist lubrication system or other devices,
it should be disconnected, and any stored air pressure released before working on the machine.
The weight of individual machine components represents stored potential energy that can be
released if they fall when disconnected. Secure these components with adequate hoisting gear
before disassembly.

1.1
SECTION 1 – INSTALLATION
Upon delivery of you r new H-14A saw, it is imperative that a thorough inspection be undertaken to check for any damage
that could have been sustained during shipping. Special attention should be paid to the electrical and hydraulic systems to
check for damaged cords and hoses or for uid leaks. In the event of damage caused during shipping, contact your carrier
to le a damage claim.
SAFETY PRECAUTIONS
The H-14A has been designed to give years of reliable service. It is essential that operators be alerted to the safe opera-
tion of this saw, and the practices to avoid that could lead to injury. The following safety rules are at a minimum for the
safe installation, operation and maintenance of the saw. Take every precaution for the protection of operators and mainte-
nance personnel.
• POWER HOOK-UPS AND REPAIRS SHOULD BE ATTEMTPED ONLY BY QUALIFIED TRADSMEN.
• THE SAW SHOULD BE LOCATED IN AN AREA WITH SUFFICENT ROOM TO SAFELY LOAD STOCK INTO
THE SAW. SECURE THE SAW TO THE FLOOR.
• THE AREA AROUND THE SAW SHOULD BE MAINTANINED IN A CLEAN AND TIDY CONDITION TO AVOID
OBSTACELS OPERATORS COULD TRIP OVER.
• THE H-14A SHOULD ONLY BE OPERATED ACCORDING TO THE SPECIFICATIONS OF THE SAW. AVOID
UNSAFE USAGE PRCATICES.
OPERATOR:
• THE SAW SHOULD NEVER BE OPERATED UNLESS ALL GUARDS AND DOORS ARE IN PLACE AND
CLOSED.
• KEEP A SAFE DISTANCE FROM ALL MOVING PARTS ESPECIALLY THE BLADE AND VISES.
• LOOSE CLOTHING AND GLOVES SHOULD NEVER BE WORN WHILE OPERATING THE SAW. COVER LONG
HAIR.
• STOCK SHOULD NOT BE LOADED ONTO THE SAW IF THE BLADE IS RUNNING.
• LONG AND HEAVY STOCK SHOULD ALWAYS BE PROPERLY SUPPORTED IN FRONT OF AND BEHIND THE
SAW.
• NEVER ATTEMPT TO DISLODGE OR MOVE STOCK WHILE THE BLADE IS MOVING. TAKE THE TIME TO
STOP THE SAW BLADE, REMOVE OBSTRUCTIONS AND RESTART THE BLADE.
• WEAR EYE PROTECTION
• MAINTAIN PROPER ADJUSTMENT OF THE BLADE TENSION, BLADE GUIDES, AND THRUST BEARINGS.
No modications to the machine are permitted without prior approval from HYD·MECH. Any modications should only be
undertaken by trained personnel.

1.2
1.3
LIFTING AND SHIPPING
This machine is designed to be lifted in one fully assembled piece. In order to lift the ma-
chine it needs to be in the following condition:
• Saw head in its bottom position.
• Shuttle vise fully forward.
• Coolant tank emptied.
The H-14A may be lifted from the front with a forklift which has a capacity of 4500 lbs
(2040 Kg) and a fork length of 72” (1830mm).
Lifting chains may be used as an alternative if used in the manner described below:
Lifting chains are fastened to 1 - 2” diameter steel bar inserted in the base where shown and 2 lugs at the front base.
FOUNDATION LEVELING AND ANCHORING
Machine location should be carefully selected. A at concrete oor area
should be chosen. It should have enough free space surrounding the
machine to enable free access for safe operation and maintenance.
The machine should be leveled in both directions, i.e. along and across
its infeed conveyor especially when machine is to be inserted into a
larger conveyor system. Six leveling screws are provided, one in each
corner of the machine base as shown below. Steel plates are to be
placed under each screw to prevent their sinking into the concrete oor.
In cases when the machine is to be anchored permanently, anchoring
holes are provided. They are located next to the leveling screws.
NOTE:
In some cases leveling the saw infeed and auxiliary conveyors with a slight slope towards the blade is recommended. This
will prevent coolant from running down the raw stock. (This is especially true when cutting tubing or bundles)
GENERAL INFORMATION
This machine has been built to the customers requirements, however, if any voltage changes are required, please consult
Hyd·Mech service department before implementing any changes.
NOTE:
1. The PLC is equipped with a lithium battery to keep the program stored while the power is shut down. The battery
will need to be replaced every 3 to 5 years, depending on usage. A visual warning will be displayed on the inter-
face when the battery drains to a certain level. Batteries can be purchased through your Hyd·Mech Distributor.
2. If the machine is equipped with an inverter, do not turn the disconnect on for 3 three minutes after disconnect has
been shut off. Cycling power sooner than 3 minuets will result in damage to the Variable Frequency Drive.
EARTH GROUNDING PROCEDURE
1. Customer to provide and install a ground rod approx. 60 (15mm) diameter, copper clad steel, to be driven no less
than 8’ (2.5m) into the ground, no more than 10’ (3m) away from control enclosure.
2. Ground rod to be connected to customer’s in plant ground system. This connection shall be made directly at the
ground rod (If applicable).
3. It is desirable that the overall resistance to ground measured at the ground rod does not exceed 3 ohms. Cus-
tomer is advised to consult local power company for further information on grounding.

1.2
1.3
4. Ground rod to be connected to ground terminal in control enclosure using insulated 8-gauge stranded copper
wire.
5. An additional point to check is ensuring continuity of ground within control enclosure. Start with main power
entrance ground terminal where internal ground conductors should originate and connect to, DIN terminal strip,
control transformer and the lid of control enclosure. Also PLC and Interface units should have their own ground
conductors connected to one of the main ground terminals.
6. Properly functioning ground system will;
• Provide safety for personnel.
• Ensure correct operation of electrical/electronic devices.
• Prevent damage to electrical/electronic apparatus.
• Help dissipate lightning strokes.
• Divert stray radio frequency (RF) energy from electronic/control equipment.
WIRING CONNECTIONS
After the machine is leveled and anchored the necessary power hook-up needs to be performed.
In order to provide a safe operation as well as to prevent potential damage to the machine, only qualied personnel
should be allowed to do the work.
The rst two areas that need to be checked are:
• There are no signs of shipping damage to electrical conduits, cords or hydraulic hoses.
• Hydraulic oil level is between the upper and lower lines on the level gauge.
As supplied, the machine is set to run on the three phase voltage as indicated on the serial plate and voltage label.
Power connection to the machine is made to the main disconnect box with the Ll, L2,L3 and Ground terminals. The dis-
connect box is located at the drive side of the machine.
During the initial hook-up it is very important to check that the phase order is correct. This is indicated by the hydraulic
pressure gauge registering a pressure rise and the blade running in a counterclockwise direction. If the hydraulics do not
register an immediate pressure rise,
- shut the hydraulics off and change the phase order.
HYDRAULIC OIL AND CUTTING FLUID
As shipped the saw oil tank is lled with Arco - Duro AW46 hydraulic oil. If you want to change the hydraulic oil or the
brand of oil, see HYDRAULIC MAINTENANCE.
No cutting uid is supplied with the machine. There are two types of coolant available:
• oil based; dilute in 1:10 ratio (one part of concentrated coolant and 10 parts of water)
• -synthetic; dilute as recommended by manufacturer.

2.1
SECTION 2 - OPERATING INSTRUCTIONS
This section has been prepared to give the operator the ability to set up the saw for most cutting situations. Before cutting
any material, the operator should be familiar with all operations and controls as well as the basic cutting theory described
below. The saw is equipped with a variable blade speed control and hydraulic feed control, as well as an extensive door
chart to guide the operator to the correct setting of these controls.
BLADE BASICS
Technology is rapidly changing all aspects of production machining. Metal cutoff is no exception. The advances made
in the bandsaw blade industry have denitely brought down the cost per cut, despite the three fold higher price of high
technology blades. Variable pitch, bi-metal blades (like the 4/6 or 3/4 bi-metal blade supplied with the machine) last much
longer, cut faster, and more accurately than conventional carbon steel blades. In order to take advantage of the superiority
of bi-metal blades, it is critical to properly “break-in” a new blade. This is accomplished by taking two or three cuts through
solid four or ve inch diameter mild steel at an extremely slow feed rate. (It is also advisable to utilize a slow blade speed.)
These two or three slow cuts sufciently lap (polish) the teeth on the new blade so that it does not snag the material being
cut. Proper break-in will alleviate blade vibration, improve surface nish, accuracy, and blade life.
After “break-in”, the following six points must be closely monitored to ensure long blade life:
1. Proper blade tension should be maintained. (see Section 3, Maintenance and Troubleshooting)
2. Generous coolant application is essential with most materials. A high quality and well mixed coolant will extend
blade life, and also increase cutting rate and quality. On those materials where coolant is undesirable for cutting,
a slight coolant ow or periodic oiling of the blade is necessary to prevent the blade from being scored by the
carbide guides.
3. The stock being cut must be securely clamped in the vises.
4. The proper feed force should be chosen. (see Saw Cutting Parameters: Step 2)
5. The proper blade speed must be selected. (see Saw Cutting parameters: Step 4)
6. The proper feed rate must be applied. (see Saw Cutting Parameters: Step 5)
VARIABLE SPEED CONTROL
Blade speed can be adjusted innitely between 60 to 350 SFM (Surface Feet/Minute) (18 to 107m/min).
Adjustment should be made only when the blade is running. Clockwise rotation of the knob increases
blade speed while counter clockwise rotation decreases blade speed.
THE CONTROL PANEL

2.2
2.3
START-UP
The H-14A control console has been designed to simplify the operation of the saw, to give the operator the ability to stop
any function at any time, and to be able to control all the functions remotely. We can not overstress the importance of
familiarizing yourself with the controls of the H-14A prior to starting the machine.
NOTE:
1. ALL SWITCHES MUST BE IN THE CENTER NEUTRAL POSITION TO START THE MACHINE!
2. WHEN STARTING THE MACHINE FOR THE FIRST TIME MAKE SURE THAT BLADE IS MOVING IN A COUN-
TERCLOCKWISE DIRECTION, AND THAT THE HYDRAULIC PRESSURE IS 700 PSI (4822kP). IF THERE IS
NO IMMEDIATE PRESSURE, SHUT THE SAW DOWN AND CHANGE THE PHASE ORDER.
MANUAL OPERATION
Manual Operations can be performed when the PLC 100 controller is set to MAN (AUTO is active when a RED light is on
above the AUTO/MAN button). All functions are self-explanatory. Specic control button functions are described on the
following pages.
Switch Operation
FRONT VISE
This switch has three positions, OPEN, HOLD and CLOSE. With the switch held in the
OPEN position the vise will open all the way or until the switch is released. With the
switch in the HOLD position, the vise will stay where it is and will not move freely although
it will not resist a large force indenitely without creeping. In CLOSE, the vise will close all
the way, or until it encounters enough resistance to stop it.
HEAD CONTROL
This switch has three positions: UP, HOLD and DOWN.
The switch is inactive unless the PLC is in manual mode. In the UP position, the head will
rise until it trips the head up limit which is adjustable via the PLC.
In the HOLD position the head will stay still.
In the DOWN position the head will descend until it reaches the bottom of the stroke. The
speed of descent is controlled by the Head Feed and Head Force Limit controls.
BLADE START
The blade can be started only when the hydraulics are running in either manual or auto
mode.
NOTE: In automatic Mode the head will not descend until the blade has been started,
which the PLC will prompt the operator to do so.
HYDRAULIC START
To start the hydraulic system, the switches for the head and both vises must be in the
“NEUTRAL” position. The “HYDRAULIC START” button must be depressed and held in
momentarily until the PLC display becomes active.
CYCLE START / PAUSE
This button starts the cutting cycles and will stay illuminated white until the cycles are
completed. The PLC control system will prompt you to start the blade if it is not running.
The machine will then begin the automatic cycle until completed when it will shut itself off.
The current cycle can be PAUSED by pressing this button at any time during a cycle and
restarted by pressing it again.
COOLANT
This switch has three positions, WASH, OFF, and ON.
In the WASH position, the coolant system will operate when there is power to the ma-
chine, this allows using the wash gun to clean the machine.
In the OFF position, the coolant system is inactive.
In the ON position the coolant system will only run when the head is descending. This
minimizes coolant carry over on the stock.

2.2
2.3
SHUTTLE VISE
This switch has three positions, OPEN, HOLD and CLOSE.
With the switch held in the OPEN position the vise will open all the way or until the switch
is released.
With the switch in the HOLD position, the vise will stay where it is and will not move freely
although it will not resist a large force indenitely without creeping.
In CLOSE, the vise will close all the way, or until it encounters enough resistance to stop
it.
BLADE SPEED This dial will increase or decrease the speed at any time while the blade is running.
BLADE STOP BUTTON Stops the blade. If the blade is stopped during a cycle, the cycle will continue but will not
let the head descend until the blade is started.
STOP
This mushroom button stops the blade and hydraulic motors. Both vises will hold their po-
sition but, pressure will begin to fall off. Long pieces of work should always be supported
so they will not become loose over time and fall while the machine is shut down. This is a
latched button and must be pulled out to start the machine.
GUIDE ARM This switch controls the position of the idler (left) guide arm.
WORK LAMP This option switch has two positions, OFF and ON.
LASER GUIDE This option switch has two positions, OFF and ON.
AUXILLARY VISE
This switch has three positions, OPEN, HOLD and CLOSE.
With the switch held in the OPEN position the vise will open all the way or until the switch
is released.
With the switch in the HOLD position, the vise will stay where it is and will not move freely
although it will not resist a large force indenitely without creeping.
In CLOSE, the vise will close all the way, or until it encounters enough resistance to stop
it.
PLC 100 CONTROL SYSTEM
NOTE:
This instruction manual is applicable to the H-14A equipped with a MITSUBISHI PLC.
OPERATION OVERVIEW
The PLC is a programmable logic controller which allows the operator to run the machine in both manual and automatic
modes.
In manual mode, all functions can be operated by using a combination of selector switches on the control console and
the PLC function buttons. Also the operator has the ability to execute a single cut utilizing a preprogrammed “Single Part
Cycle”.
In automatic mode, the PLC has the capacity to program and store 99 jobs. Designated job numbers can be programmed
for the quantity required (maximum of 999 pieces) and lengths from 0” to 220” (5588mm).
Jobs can be run individually or in a QUEUE which allows a maximum of 5 jobs to run consecutively and the queue can be
repeated automatically as well up to 99 times.
All machine operators should be familiar with the entire operation instructions prior to operating the machine.
NOTE:
If an emergency situation arises during any operation, use the large red mushroom “STOP” button located on the control
panel to shut down the machine. To operate the machine, the “STOP” button must be pulled out.

2.4
2.5
ACTIVATING THE PLC
Position the head, xed vise, and shuttle vise switches to the NEUTRAL (center) positions. If any of these switches are
not in the NEUTRAL position, the hydraulics will not start. The PLC control will become active when the HYDRAULIC
START button is depressed and “held in” momentarily. First, the HMI and PLC’s current revision number will be shown on
the display window and nally the MANUAL MODE display window will appear as shown below. The AUTO/MAN green
indicator light will be on and all MANUAL controls are enabled. The “LTH” value (shuttle vise position) will always display
zero at start up. The “LTH” value can be reset or cleared at any time in MANUAL mode by pressing the CLEAR function
button.
FUNCTION KEY DESCRIPTIONS
If a red indicator light above a function button is illuminated, it means that the function printed in red at the top of the but-
ton is enabled. No light indicates the function printed in black at the bottom of the function button is enabled.
The following are the function keys for AUTO and MAN modes:
PLC FUNCTION
KEYS
CURSOR KEYS
DISPLAY WINDOW
ENTER KEY
NUMERIC KEY PAD
BLADE SPEED
(SFM) IN SURFACE
FEET (METERS)
PER MINUTE and
SHUTTLE VISE (LTH)
POSITION