Hypercable Z24A60T37301 User manual

Manuel de montage des antennes Hautes performances Wi200-Wi700
HYPERCABLE sarl 74 Avenue Paul Sabatier ZA de la Coupe 11.100 Narbonne Tel : [phone] - Fax : [phone]
Mail : [e-mail] - N° SIRET : 384 007 894 00023 –Code TVA CEE: FR90384007894 - www.hypercable.fr
60 cm antenna Z24A60T37301
Remarks: Before Installation, please read the instruction carefully.
This instruction book is for the installation of 0.6m ultra-high performance microwave
antenna.
Installation, maintenance and removal of antenna system are suggested being carried
out by a qualified experienced personnel.
To guarantee performance, the antenna system is suggested being inspected once a year
by a qualified personnel.

Manuel de montage des antennes Hautes performances Wi200-Wi700
HYPERCABLE sarl 74 Avenue Paul Sabatier ZA de la Coupe 11.100 Narbonne Tel : [phone] - Fax : [phone]
Mail : [e-mail] - N° SIRET : 384 007 894 00023 –Code TVA CEE: FR90384007894 - www.hypercable.fr
1. Requirement of Installation
1.1 Mounting Pole
Microwave antenna can be fixed to the Mounting Pole (self-feed) of diameter from ø50 mm to
ø114 mm.
1.2 Tools Required for Installation
20×200 Adjustable Spanner (Used for bolt M10-M12)
17-19 Open-end Spanners (Used for bolt M10-M12)
3mm L-Spanner (Used for Screw M4)
Cross Screw-driver (Used for M3-M5)
Torque Spanner (Recommended)
1.3 Torque Parameters of Standard Parts
Customer can use these torque parameters as reference to assembly the antenna.
Fig 2.1 Parts List

Manuel de montage des antennes Hautes performances Wi200-Wi700
HYPERCABLE sarl 74 Avenue Paul Sabatier ZA de la Coupe 11.100 Narbonne Tel : [phone] - Fax : [phone]
Mail : [e-mail] - N° SIRET : 384 007 894 00023 –Code TVA CEE: FR90384007894 - www.hypercable.fr
3. Antenna Overall Assembly
3.1 Mount Anti-slide Bracket
Anti-slide Bracket could be mounted to the Mounting Pole(ø50~ ø114) in a way shown in Fig 3.1.
Make sure tighten the two M6x110 bolts after fixing the position.
3.2 Antenna installation
Following indications in Fig 3.2 ~ 3.3, customer could install the antenna either on the left hand
or right hand sides of the pole.

Manuel de montage des antennes Hautes performances Wi200-Wi700
HYPERCABLE sarl 74 Avenue Paul Sabatier ZA de la Coupe 11.100 Narbonne Tel : [phone] - Fax : [phone]
Mail : [e-mail] - N° SIRET : 384 007 894 00023 –Code TVA CEE: FR90384007894 - www.hypercable.fr
4. ODU radio Outdoor units
Wi200 Hyperbridge ODU

Manuel de montage des antennes Hautes performances Wi200-Wi700
HYPERCABLE sarl 74 Avenue Paul Sabatier ZA de la Coupe 11.100 Narbonne Tel : [phone] - Fax : [phone]
Mail : [e-mail] - N° SIRET : 384 007 894 00023 –Code TVA CEE: FR90384007894 - www.hypercable.fr
Wi700 Hyperbridge ODU

Manuel de montage des antennes Hautes performances Wi200-Wi700
HYPERCABLE sarl 74 Avenue Paul Sabatier ZA de la Coupe 11.100 Narbonne Tel : [phone] - Fax : [phone]
Mail : [e-mail] - N° SIRET : 384 007 894 00023 –Code TVA CEE: FR90384007894 - www.hypercable.fr
5. Antenna Adjustment
5.1 Azimuth Adjustment
Make coarse azimuth adjustment in the following way (shown in Fig 5.1): loosen the 4
nuts (No.1) of the Clamp (No.2) properly, and then push the whole structure slowly to make a
rotation from 0° to 360° around the Mounting Pole. Use compass to determine the antenna’s
position if necessary, and then tighten the nuts (No.1).
Make fine azimuth adjustment in the following way: loosen bolts (No. 5 and 6), and then
adjust nuts (No.3) of Azimuth Adjustor back and forth slowly. Antenna can make fine azimuth
adjustment from -15° to +15°; tighten all the standard parts after the adjustment is done.
5.2 Elevation Adjustment
Make elevation adjustment (shown in Fig 5.2): loosen the nuts (No.1), and then rotate
Elevation Adjustor clockwise or counterclockwise. Antenna can make fine elevation adjustment
from -15° to +15°, tighten all the standard parts after the adjustment is done.

Manuel de montage des antennes Hautes performances Wi200-Wi700
HYPERCABLE sarl 74 Avenue Paul Sabatier ZA de la Coupe 11.100 Narbonne Tel : [phone] - Fax : [phone]
Mail : [e-mail] - N° SIRET : 384 007 894 00023 –Code TVA CEE: FR90384007894 - www.hypercable.fr
Make coarse elevation adjustment (shown in Fig 5.3): loosen the bolts (No.5). Use ①&
④thread holes, antenna can make elevation adjustment from +5° to +25°. Use ②& ③thread
holes, antenna can make elevation adjustment from -5° to -25°. Tighten all the standard parts
after the adjustment is done.
6. Antenna Assembly Finishing
6.1 Tighten all the standard parts after antenna assembly are done, regard it to torque of the
standard parts is referred to the chapter 1.3.
6.2 Keep the antenna’s bottom draining-hole open. Keep the top one sealed (shown in Fig.6.1
and Fig.6.1.1).

Manuel de montage des antennes Hautes performances Wi200-Wi700
HYPERCABLE sarl 74 Avenue Paul Sabatier ZA de la Coupe 11.100 Narbonne Tel : [phone] - Fax : [phone]
Mail : [e-mail] - N° SIRET : 384 007 894 00023 –Code TVA CEE: FR90384007894 - www.hypercable.fr
7. Appendix
1. Loosen M6X25 bolts (2PCS), and then put ODU into the Transition Section (shown in Fig 7.1).
2. Tighten all the standard parts (shown in Fig 7.2).