Hytronik HEM02 User manual

INSTRUCTION MANUAL FOR EMERGENCY LED DRIVER
MODEL NO. : HEM02
Block A6, Nan’pu Science & Technology Park, Hao’si,
Shajing Street, Bao’an District, Shenzhen, P.R.C. 518104
T: 86 755 27322200 F: 86 755 27308687
E: [email protected] W: www.hytronik.com
CHINA FACTORY
Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,
Kowloon Bay, Kowloon, Hongkong
T: 00852-35197525 F: 00852-30116936
E: [email protected]
HYTRONIK INDUSTRIAL LIMITED
This emergency lighting module is designed to convert a wide range of LED types, and is an ideal choice for converting
most standard LED luminaries and arrays containing from 3 to 20 (60V) LEDs in series.
This unit is designed to utilize the existing LED driver and panel layout (no need to break into the LED circuit) to be
dimmed to 3W in case of emergency.
The driver automatically adjust the output LED current to provide the best optimum match between the battery and the
load, providing maximum illumination whilst ensuring full battery duration. The driver is compatible with a wide range of
lighting LEDs.
DESCRIPTION
WIRING DIAGRAM
Luminaire Power 5W
7W 10W 12W 15W 20W 25W 30W 35W 40W 45W 50W
60% 43% 30% 25% 20% 15% 12% 10% 9% 8% 7% 6%
It is recommended that the module is installed by a competent person ensuring the installation complies with the
neces-sary standards. Hytronik accept no resonsibility for injury, damage or loss, which may arise as a result of
incorrect installation, operation or maintenance.
The conversion requires an unswitched supoly for charging the battery and a switched supply for a maintained conversion.
BALLAST LUMEN FACTOR%
IMPORTANT

Warning
Avoid running the LED mains driver and Emergency pack without the load connected.
Failure to do so may result in damage to the LED array.
Do not short circuit or reverse connect the ba eries.
ISOLATE BOTH MAINS SUPPLIES AND DISCONNECT THE BATTERY BEFORE INSTALLATION OR MAINTENANCE.
High voltage could be present at the output terminals if the battery is not isolated.
CAUTIONS IN EMERGENCY BATTERY USAGE
STORAGE CONDITIONS
1. Temperature range for storage (Humidity: Max. 85%)
0 ~ +35℃, one year storage
(Storage time will be shortened if out of this temp. range)
2. Storage duration before use: Less than 6 months from batteries received to start with charging.
Note 1: For Ni-Cd battery, we recommend batteries are charged and discharged at least once every 6 months.
Note 2: For Ni-MH battery, we recommend batteries are charged and discharged at least once every 3 months.
Note 3: Never over discharge the battery.
WARNING
1. Avoid direct soldering onto cells.
2. Use only within the specified working temperature range.
3. Do not subject batteries to mechanical shock.
DANGER!
1. Avoid throwing cells into a fire or attempting to disassemble them. As the electrolyte inside is strong alkaline and
can damage skin and clothes.
2. Avoid short circuiting. It may be leakage.
SPECIFICATION
220-240V/AC 50/60HzMains voltage
Mains current
Mains power
19mA-21mA
4.5W
Output voltage (U-out max.) 68VDC
0.85Power factor
Operation temperature Ta: 0 ~ +50℃
Battery charge voltage 3.0V ~ 4.5V
Battery charge current Max.200mA
Battery pack 3 x 4.0 Ah C cell or 18670 type NiMH battery pack
24 hoursCharge period
+75℃Max. case temp.
Battery duration Min. 3 hours
Mains Switch-over voltage range 120VAC - 180VAC
Output LED current 40mA (60VDC) - 320mA (8VDC)
Over-heat protection Over-heat protection with auto-reset.
EN55015, EN61547EMC standard
EN50172, EN61347-2-7, EN61347-2-13, IEC62034, BS5266Safety standard
Certification Semko, CE, EMC
Dielectric strength Input →output: 3750V/AC
IP20IP grade