Hyundai power products HTDE1600 User manual

WARNING: Read thoroughly the instruction manual before use
ELECTRIC LAWN MOWER
HTDE1600

2|Page
CONTENTS
1. GENERAL SAFETY INSTRUCTIONS……………………3
2. TECHNICAL DATA………………………………………...12
3. ASSEMBLY…………………………………………..……..14
4. OPERATION………………………………………..………17
5. MAINTENANCE AND STORAGE………………………..19
6. DECLARATION CE………………………………………..21
7. WA R R A N T Y……………………………………………22
8. P R O D U C T FA I L U R E……………………………23
9. WA R R A N T Y E X C L U S I O N S……………………24

3|Page
1. GENERAL SAFETY INSTRUCTIONS
A) LEARNING
Please read the operating instructions
carefully. Familiarize yourself with the
controls and proper use of the device.
Never allow children to use the device.
Never allow persons unfamiliar with the
operating instructions to operate the
device.
Local regulations may restrict the age of
the user.
Never operate the device in the presence
of people, especially children, or pets.
The user is responsible for accidents or
risks of accidents to other people or their
property.
Use the lawnmower only for the purpose
for which it was designed, namely mowing
and collecting grass. Any other use might
be dangerous and might damage the
machine.
B) Preparation
When using the device, dress
appropriately, always wear sturdy shoes
and long pants.
Do not operate the device barefoot or with

4|Page
open sandals. Do not wear loose clothes
or jewellery. Loose clothing, jewellery or
long hair may be caught in moving parts.
Wear protective glasses during use.
Wearing a mask is recommended to
prevent dust irritation.
Before use, always perform a visual
inspection, especially of the blade, making
sure that the screws and knife assembly
are neither worn nor damaged. Replace
worn or damaged blades and all screws to
maintain balance.
Examine closely the area where you are
going to use the mower and remove all
objects that could be thrown by the
machine (stones, twigs, wire, bones etc.).
Before mowing, install and check the
condition of the grass catcher.
C) WARNINGS AND HAZARDS
Moisture and electricity do not mix well.
The handling / connection of the cables
should be done in a dry place.
Use a 30mA residual current device (RCD).
Always avoid contact between an electrical
plug or cable and a wet area (puddle or wet
grass)
The connections between the cables and
sockets should be waterproof. Only use the
extensions with waterproof sockets by

5|Page
moulding or according to current standards,
available on the market.
Power supply cables should not be of a
lower quality than type H05RN-F.
H05RR-f.H05WF.H05VVH2-F. For outdoor
use, with a minimum cross-section of 1.5
m².
Attach the cable to its hook before starting
the equipment.
The permanent connection of any electrical
device in a building should be performed
by a qualified electrician, in accordance
with current electrical standards.
A wrong connection can cause serious
injury or death.
Before connecting the device, check that
the sockets and extension cords are in
good condition. Do not use the device if it
is damaged or worn.
Never use the device if the guards are
defective or without safety devices, such
as the grass catcher in place.
Use only an extension cord attached to a
coupler according to IEC 60320-2-3
standard.
Use and operation
Always direct the cable away from the
device.

6|Page
Mow in daylight or under adequate artificial
light.
Avoid operating the device on wet grass or
in the rain.
Never run the lawnmower over the power
cable.
When mowing, the cable should always be
behind the mower and in the area where
the grass has already been cut.
Use the cable hook to avoid unexpected
disconnection of the cable.
Make sure that the plug is properly
inserted and avoid forcing the plug.
Never pull the lawnmower by its power
cable and never pull on the power cable to
remove it from the socket.
Do not expose the cable to heat sources.
Do not allow it to come into contact with
solvents, oil, fuels or sharp objects.
If a cable is damaged during use, unplug
the plug immediately. DO NOT TOUCH
THE CABLE BEFORE UNPLUGGING
THE PLUG.
Disconnect the device from power
sources
Every time you leave the device
Before you solve a problem.
Before checking, cleaning or working
on the device.

7|Page
If the device starts vibrating abnormally.
Always be careful to your position on the
slopes.
Mow facing the slopes, never from top to
bottom.
Be extremely careful when changing
direction on slopes.
Do not mow on slopes higher than 20°.
Walk, never run, never let yourself be
pulled by the lawnmower.
Be extremely careful when pulling the
lawnmower towards yourself.
Stop the engine if you have to tilt the
lawnmower to transport it, when passing
through areas other than grass, and when
transporting it to another area to mow.
Never operate the lawnmower with
defective guards or without safety devices,
such as a deflector or grass catcher, which
are not in place.
On trailed or powered models, disengage
before starting the engine.
Turn the engine on with the engine switch
on, carefully as instructed, and with your
feet well away from the blade.
Do not tilt the mower when you start the
engine.
Place the engine on a flat surface, without
obstacles or excessively high grass.

8|Page
Do not place your hands or feet under
rotating parts.
When working on the grass catcher or
ejection duct, always switch off the engine.
Never lift or carry a lawnmower with the
engine running.
Stop the engine and disconnect the power
cable:
Before performing any work behind the
cutting deck or unlocking the blade and
before checking, cleaning or working on
the lawnmower.
After striking a foreign object, stop and
disconnect the mower, check for
damage and repair before restarting
and operating it.
If the mower starts to vibrate abnormally,
stop the mower, check and eliminate
the cause of vibration.
When you leave the mower unattended.
Stop the engine:
Every time you remove or replace the
grass catcher.
Before adjusting the cutting height of
the grass.
When mowing, always keep a safe
distance from the rotating blade. This
distance corresponds to the length of the
handlebar.
After a failure, immediately stop the engine,

9|Page
do not go on mowing, take the machine to
an authorized service centre and ask for
qualified personnel to solve the problem.
C) Maintenance and storage
Regular maintenance is essential for
safety and to maintain performance levels.
Check all bolts, nuts and screws to ensure
that the device is in good working
conditions.
Inspect the condition of the grass catcher
frequently. It should always remain in
perfect condition.
Also inspect the deflector and all protection
devices.
Replace worn or damaged parts
Use only original accessories and
replacement parts.
Store the device only in a dry place.
To reduce the risk of fire, remove grass,
leaves and excess grease from the mower
and especially from the engine.
Empty, clean the grass catcher and let it
dry before storing.
Periodically check the electrical cables and
replace them if they are damaged or if the
insulation has been damaged.
Never touch a poorly insulated cable if it is
still connected to the power supply. Unplug
the cable from the socket before any
intervention.

10 |Page
Wear sturdy gloves when removing and
reassembling the blade.
Check the balance of the blade after
sharpening.
For safety reasons, do not use the mower
with worn cables or damaged parts.
Parts should be replaced and not repaired.
Use original spare parts.
Non-equivalent quality parts can damage
the mower and be dangerous to your
safety.
D) Symbols
Waste from electrical products should not be
disposed of with household waste. Please recycle
them in the dedicated facilities.
Check with your local authority or retailer for
information on recycling.
Complies with all regulatory standards in force in the
EU country where the product is bought
Risk of personal injury, death, or damage to the
device in case of non-compliance. Read the
instructions for use.

11 |Page
Risk of splashing; keep people away.
This product is doubly electrically insulated.
Beware of sharp blades. The blades continue rotating
after the engine has stopped.
Unplug the device from the mains before
maintenance, i.e. if the power cord is damaged.
Guaranteed level of sound emission
Keep the power cord away from cutting tools.

12 |Page
2. TECHNICAL DATA
a) Parts list
1. Upper handle
2. Lower handle
3. Switch box
4. Grass collection compartment
5. Wheels
6. Motor protection
7. Cable hook
7

13 |Page
b) Technical data
- Voltage: 230-240V~50Hz
- Power index: 1600W
- No-load speed: 3450min-1
- Cutting height: 25-75mm, 5 Positions
- Cutting width: 380mm
-Protection class: II
- Degree protection: IPX4
- Net weight: 12.7 kg
Sound pressure level LpA (measured at the operator level
according to EN836): 80.5 dB(A), k=3dB(A)
Sound power level (measured according to European
Directive 2000/14/EC: 93.1 dB(A), K=2.14dB(A)
Vibration value: K=1.72 m/s2 ; k=1.5 m/s2
This tool is doubly insulated. It is equipped with two insulating
sleeves to protect you from any possibility of electrical shock.
NOISE RELATED DATA
Guaranteed and declared noise intensity level: 96 db (A).
The noise level for the user may be higher than 85dB(A),
therefore, hearing protection measures are needed.

14 |Page
3. ASSEMBLY INSTRUCTIONS
CUTTING HEIGHT ADJUSTMENT
To obtain the desired cutting height, the front and rear axles are
repositioned on the underside of the mower housing.
Warning! Disconnect the mower from the power supply and
ensure the blade has stopped coasting before adjusting the
height.
Note: Make sure the right and left rear wheels are adjusted to the
same position corresponding to the cutting height.

15 |Page
1. To adjust the front wheel cutting height position (fig. 2a)
1) Turn the mower upside down.
2) Pull the wheel axle towards the front of the mower.
3) Locate the wheel axle into the desired cutting height
adjustment position.
Note: Make sure that both front right and left wheels are located
in the same cutting height adjustment position.
2. To adjust the rear wheel cutting height position (fig. 2b)
1) Turn the mower on its side.
2) Pull the rear wheel axle towards the mower’s catcher
flap.
3) Locate the wheel axle into the desire cutting height
adjustment position.

16 |Page
Note: Make sure that both rear right and left wheel are located in
the same cutting height adjustment position.
3. Cutting height positions (fig.2c)
1) 25mm (lowest cutting height position)
2) 38mm
3) 50mm
4) 63mm
5) 75mm (highest cutting height position)

17 |Page
4. OPERATING
Connect to power supply
Warning! Before connecting to the mains supply, always
check the switch is in off position. Connect the plug into the
RCD protected power supply.
a. Starting
On/Off switch fig.3)
Caution! Do not start the mower if it is standing in long grass.
Press the safety button (A) of the switch assembly and then pull
the switch lever (B) against the bar. Keep the switch lever held
whilst releasing the safety button. To stop the mower release the
switch lever and it automatically returns to its off position.
b. Mowing
We recommend using your lawnmower as described in this
section to achieve optimal results and reduce the risk of
cutting power cables.
Place the main wiring close to the starting point A.
Turn on the mower as described above.
Proceed as described in figure 4 below.
Change from position A to position B
Turn right and change to position C.
3

18 |Page
Turn left and change to position D.
Repeat the above processes if needed.
c. Instructions for the grass catcher
Putting the grass catcher in place: Lift the deflector and place
the grass catcher on the tabs.
Emptying the grass catcher: Before working on the grass
catcher, switch off the engine and wait for the blade to fully
stop.
When you see the grass scattering underneath the mowers,
empty the grass catcher. However, never use the device
without the grass catcher.
If you need to tighten the cutting blade, first make sure that
your mower is not connected to a power supply, then as
shown in the diagrams below, use a screwdriver to lock the
pin, then use a wrench to tighten the blade.
Caution! Avoid working towards the cable.

19 |Page
5. MAINTENANCE AND STORAGE
1. Keep all nuts, bolts and screws firmly tightened to ensure that
the mower can operate safely.
2. Check the mower deck and grass catcher frequently and make
sure they are not worn or damaged.
3. Replace worn or damaged parts for your safety.
4. Be sure to use only the replacement blade, its nut and wrench
specific for this product.
5. Be careful when adjusting the mower to prevent your fingers
from getting caught between the moving blade and fixed parts of
the machine.
6. Lubricate the wheel axles.
7. Store the mower in a dry place.
8. Do not wash the mower with plenty of water, wipe it with a dry
cloth. Do not spray water or liquid on the engine and electrical
components (switch, extension cord, plugs, etc.).
Blade maintenance
1. Remove grass and dirt from the blade regularly.
2. At the beginning of the gardening season, carefully
examine the condition of the blade.
3. If the blade is very blunt, sharpen or replace it.
4. If the blade is damaged or worn, replace it.
Caution! Observe the following precautions:
5. Disconnect the mower from the area and wait until the
blade has stopped rotating before proceeding.
6. Be careful not to cut yourself. Use strong work gloves or
a cloth to grasp the blade.
7. Make sure to use only the specified replacement blade.
8. Do not remove the blade (A) under any circumstances.

20 |Page
Replacing the blade:
9. Put the machine on its side.
10. Place the ring on the engine shaft.
11. Place the blade, screw and spring washer.
12. Position the blade on the centring devices.