Hyundai power products HFP1100 User manual

WARNING: Read thoroughly the instruction manual before use.
ELECTRIC WATER PUMP
HFP1100

Please note that all instructions must be consulted!
Failure to observe the following instructions and
warnings may result in electric shock, fire and / or
serious injury. Keep all instructions and warnings for
future reference. If you are giving this device to another
person, please provide this instruction manual as well.
- This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
- If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
- Use this unit as described in this manual. Any
mishandling or use contrary to these instructions
SAFETY WARNINGS
02

will in no case be the responsibility of the
manufacturer.
- Failure to observe the safety and operating
instructions may cause a risk of electric shock, fire
and / or injury to persons.
- Do not use attachments other than those
recommended by the manufacturer; they can
damage the unit and / or cause injury.
- DANGER OF SUFFOCATION! Keep packaging
materials out of the reach of children.
- Before any connection, check:
Do not damage the device or cable. In this case,
do not use the appliance and take it to your
dealer for inspection and repair.
That the voltage indicated on the rating plate of
the appliance corresponds to that of your
electrical installation.
- Do not disassemble the device yourself. Any
disassembly, repair or inspection should be carried
out exclusively by a qualified service.
- The supply cord must be easily accessible.
03

- The pump must be supplied through a residual
current device (RCD) having a rated residual
operating current not exceeding 30 mA.
- Protect the appliance and electrical connections
against moisture.
- In case of flood danger, protect the connectors.
- Avoid the discharge of aggressive liquids and the
discharge of abrasive materials.
- The submersible motor pump must be protected
from freezing.
- The submersible motor pump must not run dry.
- Disconnect the pump from the supply mains before
carrying out user maintenance such as cleaning
the filter.
- Pollution of the liquid could occur due to leakage of
lubricants.
04

SYMBOLS
Read the instruction manual
INTENDED USE
The pump is designed to suck clear water and dirty wa
ter with particles. The pump must be installed on a flat
and solid surface. It is not suitable for professional use
(including continuous operation).
GETTING STARTED
1. Install and screw the water pump outlet to the appliance (in the front).
2. Connect a discharge pipe with a diameter at least equal to the diameter of the pump outlet.
Diameter of discharge pipe
inner diameter: 40mm
outer diameter: 50mm
Connecting pipe size
1-1/2"
3. Immerse the pump in the liquid to be sucked, by making an angle of 45 degrees (to reduce the amount of air
trapped in the pump body). If the pump rests on the bottom, make sure it is on a flat and stable surface.
4. Make sure that no one is present in the liquid to be pumped.
5. Plug the pump to the mains.
05

WORKING PRINCIPLES&TECHNICAL SPECIFICATIONS
Model
HFP1100
Power
1100 W
Voltage
230V˜ 50Hz
Head max.
10 m
IP
IPX8
Temp max.
35ºC
USE OF THE PUMP
Your pump is designed for domestic use.
Your pump must not be used in following situations:
- Water temperature to be sucked is above 35°C
- Continuous run (ex: fountain pump)
- Drinking water supply or washing machines for dishes supply
- Corrosive, easily combustible, aggressive or explosive liquids (such as gasoline, petroleum), saltwater, oils
and greases.
CARE & MAINTENANCE
- In case of temporary installation, the pump must be cleaned up with clear water after use.
- In case of permanent installation, it is necessary to check every 3 months that start mechanism is working
properly (float switch or sensor).
- Regularly remove dirt that may accumulate in the sump.
- Do not expose to frost.
- Avoid dry run.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the pump.
- Clean the pump regularly if aspirated liquid cause sediments.
- Avoid shocks, do not let the pump fall.
Immersion Depth Max. 7 m
Qmax 19.5m³/h
Weight 7.5kg
06

TROUBLESHOOTING
Trouble
Check
Should do
The engine does not start
and does not make noise.
Is the pump plugged?
Does the pump starts when fully
submerged?
Check your electrical installation
Check that the float can move
freely
Pump does not deliver.
Does the impeller rotates?
Is it in good condition?
Is the pump inlet free?
The delivery head requested
exceeds the requirements of the
pump or the discharge pipe is
too narrow
Eliminate the reason for blocking
Replace the impeller
Clean the pump inlet
Use the pump in accordance with
its technical capabilities
Increase the pipe diameter
The pump stops suddenly
Did the pump run for a long
time without stopping?
Are you sure that the pump inlet
is not obstructed?
Do the power of the mains match
the rating plate?
Is the temperature of the liquid
less than 35°C?
Disconnect the pump from the
mains and let it cool for a few
tens of minutes
Clean the pump inlet
Use a power supply matching the
rating plate
Observe the maximum allowable
temperature
Flow decreases
Is the pump inlet clean?
Is the impeller clean?
The discharge pipe is not
partially clogged?
Clean the area or areas in
question (s)
07

Low flow or insufficient
Are you sure that the pump inlet
is not obstructed?
Is the impeller clean?
Are you sure that the outlet pipe
is not obstructed?
Is the diameter of the discharge
pipe enough?
Clean the zone (s) concerned
and verify check valve, if
applicable
Connecting a pipe with a suitable
diameter and suppress reduction
of the water passage
DISPOSAL
Electrical products should not be discarded with household products. According to the European
Directive 2012/19/EU on waste electrical and electronic equipment and its implementation into national law,
electrical products used must be collected separately and disposed of at collection points provided for this
purpose. Talk with your local authorities or dealer for advice on recycling.
08

WARRANTY
The manufacturer guarantees the product against defects in material and workmanship for a period of 2
years from the date of the original purchase. The warranty only applies if the product is for household use.
The warranty does not cover breakdowns due to normal wear and tear.
The manufacturer agrees to replace parts identied as defective by the designated distributor. The
manufacturer does not accept responsibility for the replacement of the machine, in whole or in part , and/or
ensuing damage.
The warranty does not cover breakdowns due to:
• insu󰀩cient maintenance.
• abnormal assembly, adjustment or operations of the product.
• parts subject to normal wear and tear.
The warranty does not extend to:
• shipping and packaging costs.
• using the tool for a purpose other than that for which it was designed.
• the use and maintenance of the machine done in a manner not described in the user manual.
Due to our policy of continuous product improvement, we reserve the right to alter or change specications
without notice. Consequently, the product may be di󰀨erent from the information contained therein, but a
modication will be undertaken without notice if it is recognized as an improvement of the preceding
characteristic.
READ THE MANUAL CAREFULLY BEFORE USING THE MACHINE.
When ordering spare parts, please indicate the part number or code, you can nd this in the spare parts list
in this manual. Keep the purchase receipt; without it, the warranty is invalid. To help you with your product,
we invite you to contact us by phone or via our website:
• +33 (0)9.70.75.30.30
• https://services.swap-europe.com/contact
You must create a "ticket" via the web platform.
• Register or create your account.
• Indicate the reference of the tool.
• Choose the subject of your request.
• Describe your problem.
• Attach these les: invoice or sales receipt, photo
of the identication plate (serial number), photo
of the part you need (for example: pins on the
transformer plug which are broken).
WARRANTY
09

WHAT TO DO IF MY MACHINE BREAKS DOWN?
If you bought your product in a store:
a) Empty the fuel tank.
b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case,
the repairer will refuse the machine.
Go to the store with the complete machine and with the receipt or invoice.
If you bought your product on a website:
a) Empty the fuel tank.
b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case,
the repairer will refuse the machine.
c) Create a SWAP-Europe service ticket on the site: https://services.swap-europe.com When making the
request on SWAP-Europe, you must attach the invoice and the photo of the nameplate (serial number).
d) Contact the repair station to make sure it is available before dropping o󰀨 the machine.
Go to the repair station with the complete machine packed, accompanied by the purchase invoice and the
station support sheet downloadable after the service request is completed on the SWAP-Europe site
For machines with engine failure from manufacturers BRIGGS & STRATTON, HONDA and RATO, please
refer to the following instructions.
Repairs will be done by approved engine manufacturers of these manufacturers, see their site:
• http://www.briggsandstratton.com/eu/fr
• http://www.honda-engines-eu.com/fr/service-network-page;jsessionid=5EE8456CF39CD572AA2AEEDFD
290CDAE
• https://www.rato-europe.com/it/service-network
Please keep your original packaging to allow for after-sales service returns or pack your machine
with a similar cardboard box of the same dimensions.
For any question concerning our after-sales service you can make a request on our website https://
services.swap-europe.com
Our hotline remains available at [phone].
PRODUCT FAILURE
10

THE WARRANTY DOES NOT COVER:
• Start-up and setting up of the product.
• Damage resulting from normal wear and tear of the product.
• Damage resulting from improper use of the product.
• Damage resulting from assembly or start-up not in accordance with the user manual.
• Breakdowns related to carburetion beyond 90 days and fouling of carburetors.
• Periodic and standard maintenance events.
• Actions of modication and dismantling that directly void the warranty.
• Products whose original authentication marking (brand, serial number) has been degraded, altered or
withdrawn.
• Replacement of consumables.
• The use of non-original parts.
• Breakage of parts following impacts or projections.
• Accessories breakdowns.
• Defects and their consequences linked to any external cause.
• Loss of components and loss due to insu󰀩cient screwing.
• Cutting components and any damage related to the loosening of parts.
• Overload or overheating.
• Poor power supply quality: faulty voltage, voltage error, etc.
• Damages resulting from the deprivation of enjoyment of the product during the time necessary for repairs
and more generally the costs related to the immobilization of the product.
• The costs of a second opinion established by a third party following an estimate by a SWAP-Europe repair
station
• The use of a product which would show a defect or a breakage which was not the subject of an immediate
report and/or repair with the services of SWAP-Europe.
• Deterioration linked to transport and storage*.
• Launchers beyond 90 days.
• Oil, petrol, grease.
• Damages related to the use of non-compliant fuels or lubricants.
* In accordance with transport legislation, damage related to transport must be declared to carriers within 48
hours maximum after observation by registered letter with acknowledgement of receipt.
This document is a supplement to your notice, a non-exhaustive list.
Attention: all orders must be checked in the presence of the delivery person. In case of refusal by the
delivery person, it you must simply refuse the delivery and notify your refusal.
Reminder: the reserves do not exclude the notication by registered letter with acknowledgement within 72
hours.
Information:
Thermal devices must be wintered each season (service available on the SWAP-Europe site). Batteries must
be charged before being stored.
WARRANTY EXCLUSIONS
11