Hyundai HSF1300 User manual

1
ELECTRIC SURFACE WATER PUMP
HSF1300
WARNING: Read thoroughly the instruction manual before use

2
SAFETY WARNINGS
Please note that all instructions must be
consulted! Failure to observe the following
instructions and warnings may result in electric
shock, fire and / or serious injury. Keep all
instructions and warnings for future reference. If
you are giving this device to another person,
please provide this instruction manual as well.
- This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not play
with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
- If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid a hazard.

3
- Use this unit as described in this manual.
Any mishandling or use contrary to these
instructions will in no case be the
responsibility of the manufacturer.
- Failure to observe the safety and operating
instructions may cause a risk of electric
shock, fire and / or injury to persons.
- Do not use attachments other than those
recommended by the manufacturer; they
can damage the unit and / or cause injury.
- DANGER OF SUFFOCATION! Keep
packaging materials out of the reach of
children.
- Before any connection, check:
Do not damage the device or cable. In this
case, do not use the appliance and take it to
your dealer for inspection and repair.
That the voltage indicated on the rating plate
of the appliance corresponds to that of your
electrical installation.
- Do not disassemble the device yourself. Any
disassembly, repair or inspection should be
carried out exclusively by a qualified service.

4
- The supply cord must be easily accessible.
- The pump must be supplied through a
residual current device (RCD) having a rated
residual operating current not exceeding 30
mA.
- Protect the appliance and electrical
connections against moisture.
- In case of flood danger, protect the
connectors.
- Avoid the discharge of aggressive liquids
and the discharge of abrasive materials.
- The submersible motor pump must be
protected from freezing.
- The submersible motor pump must not run
dry.
- Disconnect the pump from the supply mains
before carrying out user maintenance such
as cleaning the filter.
SYMBOLS
Read the instruction manual

5
INTENDED USE
The pump have been designed to suck clear
water and water with particles. The pump must
be installed on a flat and solid surface. It is not
suitable for professional use (including
continuous operation).
Layout
1 Motor cover
2 Handle
3 Switch
4 Pump head
5 Cable
6 Valve cover
7 Discharge pipe connection
8 Suction hose connection
Technical Parameters
Type
HSF1300
Input voltage (V)
230V~ 50Hz
Max. total head (m)
50
Max. flow rate ( l/h )
4500
Max. suction height (m)
8
Power
1300W
Max temperature
35ºC

6
Functions
Caution: This water pump has a water-sprinkling protection feature and should be placed only in a dry
environment. Never place the water pump or operate it in the rain or in a humid space.
Caution: This water pump should not be used with flammable or harmful liquids.
Caution: Idle operation of the water pump must be avoided.
Caution: This water pump is for work in clean water. The scope of its application includes irrigation in
the garden, water supply to a household, sprinkling in a garden or on farmland.
oThis water pump may not be exposed for long periods to impurities, sand, stone, sticky substances,
etc., mixed in with the conveyed media. Because the conveyed media may contain chemical
corrosive substances, it is necessary to pay special attention to preventing influence by these on
the material of the pump body. It is not permitted to use this water pump to convey drinking water.
Power connection
General description
Danger: During the installation of the water pump, the power supply to the water pump must be
switched off.
Caution: During installation of the equipment, it is necessary to keep it under dry and well-ventilated
conditions, at an ambient temperature below 40℃.
oBefore use, the water pump should be inspected for safety to ensure that there is no damage to the
power cable or the plug.
Electrical connection:
Danger: The Electrician responsible for installation must check to ensure that the electrical connection
is in accordance with the standard, including the earth terminal.
oThe water pump must be well earthed. If it is necessary to increase the length of the original cable,
a cable with the same section as the original cable must be used.
Taking into use
Before carrying out any work on your pump, make sure that it is switched off and that the power supply
is cut off.
The pump is not a self-priming pump. To function, it must be full of water. This is why it is necessary to
prime the water pump before operating it, during installation or after each storage period.
The suction hose must first of all be equipped with:
- A non-return valve with filter; this ensures that after disconnecting the pump, the hose and the pump
will not run dry. This part of the hose must be put in the water for it to be pumped.
- A pipe with a coupling nut; this end of the hose is attached to the front of the pump.
The two accessories must be securely screwed onto the pipe using the hose clamp supplied.
Immerse the suction hose in the source of water to be pumped to fill it with water.
Make sure that the water level does not drop when you remove it from the water.
Disconnect the discharge hose.
Unscrew the priming plug on the pump and fill it with water (use a bottle or similar container) until it
overflows.
Screw the cap back on.
Connect the discharge pipe, connect the pump to the electricity supply and start it up.

7
Pressure hose
oThe pressure hose is used for conveying the water from the pump to the water consumption point
(e.g. tap, etc.) in order to minimize the friction loss caused by the water pressure, we recommend
that you use a pressure hose with diameter of 1”.
Discharge pipe diameter
33.3mm
Suction pipe diameter
33.3mm
Maintenance
oThe appliance only needs an external regular cleaning.
oBefore cleaning the appliance, always unplug plug from supply and wait till the unit stop.
oDo not clean the painted parts with emery or solvents and use only a moistened cloth.
oIf trouble with the pump is experienced, it must be repaired by professional personnel or service
centre
Cleaning and Care
Proper and regular care will not only ensure safe use but also elongate the lifetime of this appliance.
Warning! Switch of the appliance and disconnect from power supply before you carry out cleaning and
maintenance work to avoid electrical hazard.
a) Wipe dust off with a soft dry cloth or brush.
b) To clean other debris you may use a slightly wet cloth and neutral detergent.
Note! Do not use chemical, alkaline, abrasive or other aggressive detergents or disinfector to clean this
appliance as these might be harmful to its surface.
Repair and Maintenance
This appliance does not contain any user serviceable parts. Do not try to repair the appliance yourself.
Always bring it to qualified technician
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmental safe recycling.

WARRANTY
The manufacturer guarantees the product against defects in material and workmanship for a period of 2
years from the date of the original purchase. The warranty only applies if the product is for household use.
The warranty does not cover breakdowns due to normal wear and tear.
The manufacturer agrees to replace parts identied as defective by the designated distributor. The
manufacturer does not accept responsibility for the replacement of the machine, in whole or in part , and/or
ensuing damage.
The warranty does not cover breakdowns due to:
• insu󰀩cient maintenance.
• abnormal assembly, adjustment or operations of the product.
• parts subject to normal wear and tear.
The warranty does not extend to:
• shipping and packaging costs.
• using the tool for a purpose other than that for which it was designed.
• the use and maintenance of the machine done in a manner not described in the user manual.
Due to our policy of continuous product improvement, we reserve the right to alter or change specications
without notice. Consequently, the product may be di󰀨erent from the information contained therein, but a
modication will be undertaken without notice if it is recognized as an improvement of the preceding
characteristic.
READ THE MANUAL CAREFULLY BEFORE USING THE MACHINE.
When ordering spare parts, please indicate the part number or code, you can nd this in the spare parts list
in this manual. Keep the purchase receipt; without it, the warranty is invalid. To help you with your product,
we invite you to contact us by phone or via our website:
• +33 (0)9.70.75.30.30
• https://services.swap-europe.com/contact
You must create a "ticket" via the web platform.
• Register or create your account.
• Indicate the reference of the tool.
• Choose the subject of your request.
• Describe your problem.
• Attach these les: invoice or sales receipt, photo
of the identication plate (serial number), photo
of the part you need (for example: pins on the
transformer plug which are broken).
WARRANTY
8

WHAT TO DO IF MY MACHINE BREAKS DOWN?
If you bought your product in a store:
a) Empty the fuel tank.
b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case,
the repairer will refuse the machine.
Go to the store with the complete machine and with the receipt or invoice.
If you bought your product on a website:
a) Empty the fuel tank.
b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case,
the repairer will refuse the machine.
c) Create a SWAP-Europe service ticket on the site: https://services.swap-europe.com When making the
request on SWAP-Europe, you must attach the invoice and the photo of the nameplate (serial number).
d) Contact the repair station to make sure it is available before dropping o󰀨 the machine.
Go to the repair station with the complete machine packed, accompanied by the purchase invoice and the
station support sheet downloadable after the service request is completed on the SWAP-Europe site
For machines with engine failure from manufacturers BRIGGS & STRATTON, HONDA and RATO, please
refer to the following instructions.
Repairs will be done by approved engine manufacturers of these manufacturers, see their site:
• http://www.briggsandstratton.com/eu/fr
• http://www.honda-engines-eu.com/fr/service-network-page;jsessionid=5EE8456CF39CD572AA2AEEDFD
290CDAE
• https://www.rato-europe.com/it/service-network
Please keep your original packaging to allow for after-sales service returns or pack your machine
with a similar cardboard box of the same dimensions.
For any question concerning our after-sales service you can make a request on our website https://
services.swap-europe.com
Our hotline remains available at [phone].
PRODUCT FAILURE
9

THE WARRANTY DOES NOT COVER:
• Start-up and setting up of the product.
• Damage resulting from normal wear and tear of the product.
• Damage resulting from improper use of the product.
• Damage resulting from assembly or start-up not in accordance with the user manual.
• Breakdowns related to carburetion beyond 90 days and fouling of carburetors.
• Periodic and standard maintenance events.
• Actions of modication and dismantling that directly void the warranty.
• Products whose original authentication marking (brand, serial number) has been degraded, altered or
withdrawn.
• Replacement of consumables.
• The use of non-original parts.
• Breakage of parts following impacts or projections.
• Accessories breakdowns.
• Defects and their consequences linked to any external cause.
• Loss of components and loss due to insu󰀩cient screwing.
• Cutting components and any damage related to the loosening of parts.
• Overload or overheating.
• Poor power supply quality: faulty voltage, voltage error, etc.
• Damages resulting from the deprivation of enjoyment of the product during the time necessary for repairs
and more generally the costs related to the immobilization of the product.
• The costs of a second opinion established by a third party following an estimate by a SWAP-Europe repair
station
• The use of a product which would show a defect or a breakage which was not the subject of an immediate
report and/or repair with the services of SWAP-Europe.
• Deterioration linked to transport and storage*.
• Launchers beyond 90 days.
• Oil, petrol, grease.
• Damages related to the use of non-compliant fuels or lubricants.
* In accordance with transport legislation, damage related to transport must be declared to carriers within 48
hours maximum after observation by registered letter with acknowledgement of receipt.
This document is a supplement to your notice, a non-exhaustive list.
Attention: all orders must be checked in the presence of the delivery person. In case of refusal by the
delivery person, it you must simply refuse the delivery and notify your refusal.
Reminder: the reserves do not exclude the notication by registered letter with acknowledgement within 72
hours.
Information:
Thermal devices must be wintered each season (service available on the SWAP-Europe site). Batteries must
be charged before being stored.
WARRANTY EXCLUSIONS
10