I-care S Series User manual

S Series Security Mobile Phone
Model: S 3300
User Manual

2
Important Safeguards
Before you begin any setup, please note the following:
1. You MUST insert a SIM card before you begin any setup
2. You will need to use another mobile phone which has LED display in order to set up the S
SERIES Security Phone
3. Please read this user manual thoroughly and follow the instructions for phone setup
Please read through this manual before using S SERIES Security Phone
•Keep the phone in clean area
•Do not immerse the phone to liquid, wet or moisture environment
•Do not expose the phone to extreme temperatures
•Do not place the phone in microwave oven, which may cause serious hazards
•Do not expose near fire or any other inflammable materials
•Do not drop, throw or bend the phone
•Do not paint on the phone
•Do not use the phone near medical facility or equipment without permission
•Do not use the phone in aircraft or in areas posted “turn off two-way radio”
•Do not use the phone in any area may have potential explosive atmosphere
•Do not affix the mobile phone or any RF accessories on the airbag of motor
vehicle
•Do not attempt to disassemble the phone. Any maintenance or repair should only
be performed by authorized service personnel
4. FCC Regulations:
zThis mobile phone complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
zThis mobile phone has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiated radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

3
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate the equipment.
Published by:
I-Care Telecom Inc.
Website: www.i-care.net.tw

4
Table of Content
Chapter 1 Identification ..............................................................................................5
1-1 Key components of Security Phone..............................................................5
1-2 S SERIES Security Phone accessories ................... 錯誤! 尚未定義書籤。
1-3 User Instruction ............................................................................................8
1-3-1 SOS group setup................................................................................8
1-3-2 SMS setup .........................................................................................8
1-3-3 SMS delay .........................................................................................7
1-3-4 Password............................................................................................7
1-3-4-1 Original password .............................................................................7
1-3-4-1 Password change...............................................................................7
1-3-5 Maintenance ......................................................................................7
1-3-5-1 Battery............................................................................................7
1-3-5-2 Keypad ...........................................................................................7
1-3-5-3 Other parts maintenance ................................................................7
1-3-5-4 Wet .................................................................................................8
1-3-6 Other suggestions ..........................................................................9
1-3-6-3 Avoid high temperature..................................................................9
1-3-6-4 Privacy ...........................................................................................9
1-3-6-5 SIM card password ........................................................................9
Chapter 2 Function introduction ...............................................................................10
2-1 General..........................................................................................................9
2-2 Text Message ................................................................................................9
2-3 Speed Dial keypads ......................................................................................9
2-4 Authorization ................................................................................................9
2-5 Setting confirmation .....................................................................................9
2-6 Setting change confirmation.........................................................................9
2-7 Low battery notice ........................................................................................9
2-8 One-way communication..............................................................................9
Chapter 3 Getting Start ...........................................................................................10
3-1 Install battery .............................................................................................. 11
3-2 Turn on the phone .......................................................................................10
3-3 LED indicator ............................................................................................. 11
Chapter 4 Operation and Setup Instructions .............................................................12
4-1 Receiving/End calls ....................................................................................12
4-2 Making calls ...............................................................................................12
4-3 Setup speed dial keypads............................................................................13
4-3-1 Dial out number setup .............................................................................13
4-3-2 Setup short message service ..................................................................14
4-3-3 Change message text ...............................................................................17

5
4-4 SOS Group iniforming............................................................................17
4-4-1 Setup SOS receivers ................................................................................18
4-4-2 Setup SOS message.................................................................................19
4-5 Earphone.....................................................................................................19
4-6 Speaker Volume ..........................................................................................19
4-8 Switching to vibrate/ring mode ..................................................................20
4-9 Change Ring Volume..................................................................................20
4-10 Setup confirmation ...................................................................................20
4-11 One way communication ..........................................................................21
4-12 Password...................................................................................................22
4-12-1 Change password...................................................................................22
4-12-2 Forget password ....................................................................................22
Chapter 5 Battery Management..................................................................................23
Chapter 6 Specification.............................................................................................24
Chapter 7 Additional Guidelines ..............................................................................25

6
Chapter 1: Identification
SOS button Call
End Call/Power On-Off
Signal LED
Chain Holder
Speed Dial 1 Speed Dial 2
Speed Dial 3 Speed Dial 4
Speaker
SOS button
Battery cover
Cover release button

7
1-2 S SERIES Security Phone accessories
It is suggested that use only S SERIES accessories for S SERIES Security Phone!
zSafety neck chain
zPower charger
zLi-ion battery
zOptional belt clip
zOptional car charger

8
1-3GeneralInstruction
1-3-1 SOS group setup
Important Note:
You must setup the First SOS dialers number (see 4-4-1) in order to receive a confirmation
SMS for each setup afterwards.
Important: Setup of S SERIES Security Phone is different to other mobile phones. Please
setup the SOS function to ensure its proper operation (see chap 4-4)
1-3-2 SMS setup
When you first use S SERIES Security Phone, setup the short messages and SOS message to
ensure these two functions are operating properly (see 4-3-2)
1-3-3 SMS delay
S SERIES Security Phone is transmitting via SMS. In case of peak hour to transmit short
messages, the messages might be delay during transmission (e.g. Christmas, New Year…etc)
1-3-4 Password
S SERIES Security Phone is also available with short messages function other than normal
communication. Remember your password, since password verification will be required before
any change of setting in order to protect personal privacy and security.
1-3-4-1 Original password
Original password is 0000. Please change the password immediately after purchase.
Remember your new password since new password is not available to anyone including S
SERIES Co.
1-3-4-2 Password Change
Change your password from time to time and do not disclose password to unknown person.
Damage derived from disclose of password is not the liability of S SERIES Co.
1-3-5 Maintenance
Do not use any other accessories than S SERIES originals. Failure to do so may result in loss
ofperformanceandwillvoidthewarranty.
1-3-5-1 Battery
Do not expose battery in extreme temperatures which might shorten the battery usage life.
Do not store battery with metal objects that could damage the battery pack or cause fire or
burns.
1-3-5-2 Keypad
Clean the keypads surface with phone turn off. Remove the power cable (charger) and clean it
with dry and soft cloth to avoid short circuit of the phone. In case the phone is wet, do not
turn on the phone and contact S SERIES customer service center on (phone number)

9
1-3-5-3 Other parts maintenance
Follow the steps below to clean and maintain the phone and phone accessories:
Step one: make sure the power is turned off, remove the battery and power cable (charger)
Step two: use small vacuum cleaner to clean any connector and keypads
Step three: Clean the phone with a soft cloth dampened with water. Make sure no liquid is leak
inside the phone to cause short circuit.
1-3-5-4 Wet
Do not turn on the phone when it is wet. This will cause serious damage to the phone. Do as
follow:
Step one: Remove power cable and battery
Step two: Remove water from the phone and clean it with soft cloth
Step three: Dry the phone with fan and contact S SERIES customer service center immediately
on (phone number). Do not use hair dryer. High temperature may damage the phone. (Do not
place the phone to the mobile phone cover if the mobile phone cover is wet)
1-3-6 Other Suggestions
1-3-6-1 Avoid high temperature
Do not expose phone to extreme high temperature. Doing so will damage the phone.
1-3-6-2 Privacy
Do not use the phone to steal others privacy. Violation of privacy law is not the liability of S
SERIES Co.
1-3-6-3 SIM card password
Use mobile phone with display to unlock SIM card password before use it in S SERIES
Security Phone.

10
Chapter 2: Functions
2-1 General
S SERIES Security Phone provides GSM 900/1800/1900 Tri band service to receive and
make calls.
2-2 Text Message
Four speed dial keypads are able to send pre-programmed message (see sec 4-3-2).
2-3 Speed Dial Keypads
S SERIES Security Phone provides four speed dial keypads. The dial out number is to be
pre-programmed via message setting. S SERIES Security Phone is specially designed for the
children; therefore, there is no number keypads in order to avoid wrong dialing and complex
user interface.
SOS side keypads can immediately send pre-programmed message to three pre-programmed
receivers (see sec 4-4). SOS buttons serve as a speed dial keypad for emergency case. For
example, when a child is sick in school, he/she can use SOS Button sending pre-programmed
message to inform receivers. It is suggested that the first receiver to be the most important
contact person to achieve its urgency, safety and privacy (see sec 4-4)
2-4 Authorization
Only the authorized users could use message function to change relevant setting of S SERIES
Security Phone
2-5 Setting Confirmation
After security check, the user can use message function requesting S SERIES Security Phone
to confirm speed and SOS dial out number.
2-6 Setting Change Confirmation
When the setting changed, confirmation message will be send to the pre-programmed first
receiver to verify correctness of the setting.
2-7 Low Battery Notice
S SERIES Security Phone will send message to the first receiver when the battery is low.

11
This is to prevent discontinue of operation during low battery.
2-8 One-way Communication
Special feature is available to monitor the live sounds of S SERIES Security Phone
surrounding environment (see sec 4-10).
Chapter 3: Getting Start
3-1 Install Battery
Place the battery in the direction of the arrow as shown in the picture to ensure the safety of S
SERIES Security Phone. When battery is installed, LED light will be flashing and the phone
is turned on. This is to test whether the battery is correctly installed. Please do not be alarmed
when the light is flashing.
3-2 Turn on the phone
Turn on: Press the “End Call” key for two to three seconds, when the LED light flashing in
green, it indicates network is well and ready for use (if there is no network, it shows a steady
blue light)
Turn off: Press “End call ” for 3 seconds and the phone will be turned off.

12
3-3 LED indicator
In normal operating status, the LED light will be flashing in green; if there is no network, it
shows a steady green. When there is an incoming call, LED light will be flashing rapidly.
When the battery is low, LED light will be flashing in red. If the battery is required to be
charged, it shows a steady red light.
If SIM card is not inserted or installed properly, LED light will be flashing in blue.
Chapter 4: Operation
How to Setup Security Phone:
Important Note Before You Start to Setup:
There are two types of methods for setting up your Security Phone (to pre-program the Speed
Dials, Text Messages and SOS dials.) Please note that you may choose EITHER method
that would work best for you.
Setup Method I
Place the SIM card in a regular mobile phone to setup
1. Initiating the SIM card in Security Phone:
Place the SIM card into the Security Phone and turn it on. The Security Phone will format
the SIM card memory and make it ready for setup. When the initiation is finished, the
Security Phone LED lights will flash in seven colors for about 3 seconds as the confirmation.
You would need to know the password to proceed with each setting (the manufacturer
password is preset as 0000).
2. Use a regular mobile phone to setup:
Next, remove the SIM card from Security Phone and place it into a regular mobile phone that
has a display. Follow the manufacturer’s password: 0000 to complete each setup. See the
setup reference table below for instructions to setup phone numbers and text messages.
3. When finished entering all telephone numbers, escape from the Phone Book. When
finished entering all pre-setup text messages, escape from the Text Message Box.
CHANGE PASSWORD 0000
SPEED DIAL 1 PHONE NUMBER
SPEED DIAL 2 PHONE NUMBER
SPEED DIAL 3 PHONE NUMBER

13
SPEED DIAL 4 PHONE NUMBER
SOS 1 MOBILE NUMBER
SOS 2 MOBILE NUMBER
SOS 3 MOBILE NUMBER
SIM RECOGNITION CODE #*66#*
TEXT MESSAGE 1 MESSAGE CONTENT
TEXT MESSAGE 2 MESSAGE CONTENT
TEXT MESSAGE 3 MESSAGE CONTENT
TEXT MESSAGE 4 MESSAGE CONTENT
SOS TEXT MESSAGE MESSAGE CONTENT
5. Now, replace the same SIM card into the Security Phone and turn it back on. When
turned on, the Security Phone will detect the SIM phone book automatically. To
reconfirm that all phone numbers and messages were setup successfully, go to the 9th slot
in SIM phone book to double check.
6. If the Security Phone is turned with normal procedures, the 1st Speed Dial call recipient
will get three confirmation SMS from the Security Phone:
(a) Speed Dial 1 “XXXXXXXX”, Speed Dial 2 “XXXXXXXX”, Speed Dial 3
“XXXXXXXX”, Speed Dial 4 “XXXXXXXX”.
(b) SOS Dial 1 “XXXXXXXX”, SOS Dial 2 “XXXXXXXX”, SOS Dial 3
“XXXXXXXX”
(c) PASSWORD “XXXX”
Setup Method II:
Sending SMS to the Security Phone from a another mobile phone to setup
1. Place the SIM card into the Security Phone.
2. Use another mobile phone to send SMS to the Security Phone to setup all the phone
numbers and text messages. Follow the How to Setup table below to setup the Security
Phone by sending SMS from another mobile phone to the Security Phone.
How to Setup *password*function code*preprogram number#
Password change * password * 00 * preprogram number #
(4 digits for password)
Speed dial 1 * password * 11 * preprogram number #
Speed dial 2 * password * 12 * preprogram number #
Speed dial 3 * password * 13 * preprogram number #
Speed dial 4 * password * 14 * preprogram number #

14
SOS dial 1 * password * 21 * preprogram number #
SOS dial 2 * password * 22 * preprogram number #
SOS dial 3 * password * 23 * preprogram number #
Setup confirmation * password * 30 *#
One-way communication * password * 40 * preprogram number #
Message setup 1 * password * T1 * preprogram number #
Message setup 2 * password * T2 * preprogram number #
Message setup 3 * password * T3 * preprogram number #
Message setup 4 * password * T4 * preprogram number #
SOS Message setup * password * T5 * preprogram number #
Important Note:
You must setup the First SOS dialers number in order to receive a confirmation SMS for each
setup afterwards.
* Setup SOS receivers (1)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*21*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the first receiver number is
0915111111. Then you enter “*0000*21*0915111111#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed. A confirmation message will send to the pre-programmed first
receiver in a few seconds.
4-1 Receiving / End calls
When the phone rings (or vibrates):
Step one: press Receiving/Dialing’’ button
Step two: press “Power off / on’’ button to end a call
End Call/Power On-Off On
Receiving/Dialing Button

15
4-2 Making calls
Step one: press any speed dial keypad
Step two: press dial out keypad within 3 seconds; if dial out keypad is not press within 3
seconds, it would be considered as an error
4-3 Setup speed dial keypads
4-3-1 Dial out number setup
Speed dial function is available to the users. Please follow below instruction to setup the
speed dial numbers: (to setup with extension number, add letter “p” in lower case after the
phone number eg. 02-33331111p123)
*Setup speed dial keypad (1)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*11*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the dial out number is
0930123456. Enter “*0000*11*0930123456#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
dial out number setup is completed. A confirmation message will send to the
pre-programmed first receiver in a few seconds.
How to use: Press first speed dial keypad then press dial-out key to make calls.
*Setup speed dial keypad (2)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*12*number#”. (Original password is 0000).
Speed dial 2
Speed dial 4
Speed dial 1
Speed dial 3

16
Step two: For example, if your password is 0000 and the dial out number is
0910123456. Enter “*0000*12*0910123456#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
dial out number setup is completed. A confirmation message will send to the
pre-programmed first receiver in a few seconds.
How to use: Press second speed dial keypad then press dial-out key to make calls
*Setup speed dial keypad (3)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*13*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the dial out number is
0912123456. Enter “*0000*13*0912123456#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
dial out number setup is completed. A confirmation message will send to the
pre-programmed first receiver in a few seconds.
How to use: Press third speed dial keypad then press dial-out key to make calls
*Setup speed dial keypad (4)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*14*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the dial out number is
0913123456. Enter “*0000*14*0913123456#”
Step three: Send the message to S SERIES Security Phone. When the LED light is
on, dial out number setup is completed. A confirmation message will send to the
pre-programmed first receiver in a few moments.
How to use: Press forth speed dial keypad then press dial-out key to make calls
4-3-2 Setup Short Message Service (SMS)
S SERIES Security Phone can send SMS and it can store four set of preprogrammed message
and one set of dial out numbers
Use mobile phone with display to do the setup. (Message text is limited to 60 Chinese
characters)
T1: Speed dial keypad 1

17
T2: Speed dial keypad 2
T3: Speed dial keypad 3
T4: Speed dial keypad 4
T5: SOS group dial keypad
*Set up SMS (1)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*T1*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the SMS is “Daddy, I love you”.
Then you enter “*0000*T1*Daddy, I love you#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed.
How to use: Press first speed keypad for three seconds until the red and blue light is
on, and then the message is sent.
*Set up SMS (2)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*T2*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the SMS is “Mummy, I love
you”. Then you enter “*0000*T2*Mummy, I love you#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed.
How to use: Press second speed keypad for three seconds until the red and blue light
is on, and then the message is sent.
*Set up SMS (3)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*T3*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the SMS is “Grandma, I am
hanging out with friend”. Then you enter “*0000*T3* Grandma, I am hanging out
with friend#”

18
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed.
How to use: Press third speed keypad for three seconds until the red and blue light is
on, and then the message is sent.
*Set up SMS (4)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*T4*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the SMS is “Teacher, I am
home”. Then you enter “*0000*T4*Teacher, I am home#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed.
How to use: Press forth speed keypad for three seconds until the red and blue light is
on, and then the message is sent.
*Set up SOS message
Step one: Access to “write message” function in mobile phone with display, enter
“*password*T5*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the SMS is “Mum, I am sick”.
Then you enter “*0000*T5*Mum, I am sick#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed.
How to use: Press SOS Button on both sides. When the S SERIES Security Phone
vibrates, SOS message is sent to the preprogrammed receiver.
4-3-3 Change message text
To change the SMS, repeat section 4-3-2 in the user manual. Previous SMS will be replaced
with the new messages.
4-4 SOS Group Informing
Step one: In case of emergency, press SOS Button on both sides for 3 seconds
Step two: Release the keypads when the phone vibrate for 0.5 seconds. The fixed SOS
message is then sent to the three preprogrammed receivers.
Step three: Once the SOS message is sent to the three preprogrammed receivers,

19
S SERIES Security Phone will auto dial to the first receiver if the receiver answer the
phone so that the receiver can monitor the life sounds surrounding S SERIES Security
Phone.
4-4-1 Setup SOS receivers
Press SOS Button on both sides, text message will be sent to the preprogrammed three
receivers. It is suggested that the first receiver to be the most important contact person in case
of emergency.
* Setup SOS receivers (1)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*21*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the first receiver number is
0915111111. Then you enter “*0000*21*0915111111#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed. A confirmation message will send to the pre-programmed first
receiver in a few seconds.
How to use: Press SOS Button on both sides. When the S SERIES Security Phone
vibrates, SOS message is sent to the preprogrammed receivers.
* Setup SOS receivers (2)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*22*number#”. (Original password is 0000).
SOS ButtonSOS Button

20
Step two: For example, if your password is 0000 and the first receiver number is
0915111111. Then you enter “*0000*22*0916111111#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed. A confirmation message will send to the pre-programmed first
receiver in a few seconds.
How to use: Press SOS Button on both sides. When the S SERIES Security Phone
vibrates, SOS message is sent to the preprogrammed receivers.
* Setup SOS receivers (3)
Step one: Access to “write message” function in mobile phone with display, enter
“*password*23*number#”. (Original password is 0000).
Step two: For example, if your password is 0000 and the first receiver number is
0915111111. Then you enter “*0000*23*0917111111#”
Step three: Send the message to S SERIES Security Phone. When the LED light is on,
setup is completed. A confirmation message will send to the pre-programmed first
receiver in a few moments.
How to use: Press SOS Button on both sides. When the S SERIES Security Phone
vibrates, SOS message is sent to the preprogrammed receivers.
4-4-2 Setup SOS message
See SMS setup in section 4-3-2
4-5 Earphone
Earphone is available with S SERIES Security Phone
Step one: insert earphone to the earphone port as shown in the diagram below
Step two: answer and make calls via earphone
4-6 Speaker Volume
To change speaker volume during a call, press speed dial key 1 to increase volume and speed
dial key 2 to decrease volume