IBASE Technology FWA6604 series User manual

FWA6604 series
Network Appliance
Users Manual
Version 1.0

FWA6604 Series User’s Manual
1
Table of Contents
Table of Contents ………………………………………………………………………………………………1
Foreword ……………………………………………………………………………………………………..2
Chapter 1 Introduction......................................................................................................................4
Chapter 2 System Specification.......................................................................................................5
Chapter 3 Hardware Configuration...................................................................................................6
Chapter 4 Console Mode Information.............................................................................................11
Chapter 5 Opening the Chassis.....................................................................................................13
Chapter 6 Installing CompactFlash Card........................................................................................13
Chapter 7 Installing Memory Module..............................................................................................14
Chapter 8 Installing Mini PCI-e Module..........................................................................................14
Chapter 9 Installing 2.5” SSD.........................................................................................................15
Chapter 10 Lock Power Connector ..................................................................................................16

FWA6604 Series User’s Manual
2
Foreword
Copyright© 2014 IBASE Technology INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except
documentation kept by the purchaser for backup purposes, without the express written permission of IBASE
Technology INC. (“IBASE”).
Products and corporate names mentioned in this manual may or may not be registered trademarks or copyrights of
their respective companies, and are used for identification purposes only. All trademarks are the property of their
respective owners.
Every effort has been made to ensure that the contents of this manual are correct and up to date. However, the
manufacturer makes no guarantee regarding the accuracy of its contents, and reserves the right to make changes
without prior notice.
Safety Information
FWA6604 is designed and tested to meet the latest standards of safety for information technology equipment.
However, to ensure your safety, it is important that you read the following safety instructions.
Setting up your system
• Read and follow all instructions in the documentation before you operate your system.
•Do not use this product near water.
•Set up the system on a stable surface or secure on wall with the provided rail. Do not secure the system on any
unstable plane or without the rail.
•Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to
the product.
•Slots and openings on the chassis are for ventilation. Do not block or cover these openings. Make sure you
leave plenty of space around the system for ventilation. Never insert objects of any kind into the ventilation
openings.
•This system should be operated from the type of power indicated on the marking label. If you are not sure of the
type of power available, consult your dealer or local power company.
•Use this product in environments with ambient temperatures between 0˚C and 40˚C.
•If you use an extension cord, make sure that the total ampere rating of the devices plugged into the extension
cord does not exceed its ampere rating.
Care during use
• Do not walk on the power cable or allow anything to rest on it.
•Do not spill water or any other liquids on your system.
•When the system is turned off, a small amount of electrical current still flows.
•Always unplug all power, and network cables from the power outlets before cleaning the system.
•If you encounter the following technical problems with the product, unplug the power cord and contact a
qualified service technician or your retailer.
➢The power cable or plug is damaged.
➢Liquid has been spilled into the system.
➢The system does not function properly even if you follow the operating instructions.
➢The system was dropped or the cabinet is damaged.
Lithium-Ion Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type
recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

FWA6604 Series User’s Manual
3
NO DISASSEMBLY
The warranty does not apply to the products that have been disassembled by users
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
•This device may not cause harmful interference, and
•This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the
user’s authority to operate the equipment.
CE Mark Warning
This is a Class A product, in a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.

FWA6604 Series User’s Manual
4
Chapter 1 Introduction
The FWA6604 series was specifically designed for the network security &
management market.
Network Security Applications:
•Firewall
•Virtual Private Network
•Proxy Server
•Caching Server
Network Management Applications:
•Load balancing
•Quality of Service
•Remote Access Service
The FWA network appliance product line covers the spectrum from offering
platforms designed for :
•SOHO
•SMB
•Enterprise
Each product is designed to address the distinctive requirements of its
respective market segment from cost effective entry-level solutions to
high throughput and performance-bound systems for the Enterprise level.

FWA6604 Series User’s Manual
5
Chapter 2 System Specification
Product Description
FWA6604 incorporates Intel® SoC. Currently, it is available in the following model:
Model
Intel® SoC
Fanless
2.5”HDD
Support
FWA6604-1C
AtomTM E3815
1.46 GHz
Yes
Yes
FWA6604-4C
Celeron® J1900
2.00 GHz
No
Yes
FWA6604 Features
•Supports four intel® 10/100/1000 LAN ports
•DDR3L SO-DIMM x 1, up to 4GB
•Half-sized Mini PCI-e slot & Compact Flash socket
FWA6604 Specifications
CPU Type
Operating Frequency
FWA6604-1C: Intel® AtomTM Single core processor
E3815 (512K cache, 1.46 GHz)
FWA6604-4C: Intel® Celeron® Quad cores processor
J1900 (2M cache, 2.0 GHz)
BIOS
AMI BIOS w/ACPI
Ethernet controller
Intel® I211-AT PCI Express Gigabit ethernet controller x4
Memory
CPU on-die memory controller supporting up to 4GB
One DDR3L-1600 SO-DIMM socket, Non-ECC, unbuffered, 1.35V
LAN
Console: RS-232 @ RJ45
Eth1, 2, 3 & 4: Intel® I211-AT @ RJ45 with LED
Network Bypass
One segment IBASE Advanced Bypass (Eth3 & 4)
Control by GPIO / Watchdog
Watchdog Timer
Yes (256 segments, 0, 1, 2…255 sec/min)
Storage
Onboard CF socket x1
7-pin SATA connector x1
Rear Panel
Cylindrical (Tip) Connector DC +12V inlet with Screw Lock
Factory Mode Restore Reset Switch (GPIO control)
Power On / Off Switch
Optional opening for Wireless LAN antenna
RJ45 x1 for Console
RJ45 with LED x4 for Gigabit LAN
USB 2.0 x1
Front Panel
LED: Power (Green) / Alarm (Red) / Status (Yellow)
LAN Speed LED (Yellow / Green) x4
LAN Link / Act LED (Green) x4
USB 2.0
USB 2.0 x4
External x2
[2x4] Pin header Onboard x1
Mini PCI-e Socket x1
Video
VGA pin header on board (IBASE VGA8 cable)
Internal I/O Headers
4-pin Smart Fan Connector x1
2-pin header for DC-in (12V) x1
Expansion Interface
Half-sized Mini PCI-e socket x1
Power Supply
Full range 40W Adapter / 12V
Dimensions
187(W) x 115.8(D) x 44(H) mm
Operation Temperature
FWA6601-1C: 0 ~ 40 ˚C (32 ~ 104 ˚F)
FWA6601-4C: 0 ~ 45 ˚C (32 ~ 113 ˚F)
Storage Temperature
-20 ~ 70 ˚C (-4 ~ 158 ˚F)

FWA6604 Series User’s Manual
6
Chapter 3 Hardware Configuration
Motherboard (MB839 Series) Layout
JP2: BIOS Flash Security Setting
Pin #
Signal Name
1
GND
2
I2S_2_TXD
JP3: Clear CMOS Setting
JP2
Setting
Normal
Clear CMOS
JP4: Clear ME Setting
JP3
Setting
Normal
Clear ME

FWA6604 Series User’s Manual
7
JP5: VGA Connectors
Signal Name
Pin #
Pin #
Signal Name
VGA_R
1
2
VGA_PWR
VGA_G
3
4
GND
VGA_B
5
6
NC
NC
7
8
VGADDCDATA
GND
9
10
HSYNC
GND
11
12
VSYNC
GND
13
14
VGADDCCLK
GND
15
JP6: LPC Debug Port
Signal Name
Pin #
Pin #
Signal Name
LPC_AD0
1
2
SIO_PLTRST#
LPC_AD1
3
4
LPC_FRAME#
LPC_AD2
5
6
+3.3V
LPC_AD3
7
8
Ground
LPC_CLK
9
JP7: SPI Debug Port
Signal Name
Pin #
Pin #
Signal Name
NC
1
2
NC
SPI_CS#0
3
4
+1.8V
SPI_SO
5
6
SPI0_HOLD#
SPI0_WP#
7
8
SPI_CLK
GND
9
10
SPI_SI
JP12: System Function Connector
JP12 provides connectors for system indicators that provide light indication of the computer activities and
switches to change the computer status. JP12 is a 8-pin header that provides interfaces for the following
functions
Pin 1,2: Power LED
The power LED indicates the status of the main power switch.
Pin #
Signal Name
1
+5V
2
GND
Pin 3,4: ATX Power ON Switch
Pin 3 & 4 are for “ATX Power Supply On/Off Switch” on the system that connects to the power switch
on the case. When pressed, the power switch will force the system to power on. When pressed
again, it will force the system to power off.
Pin #
Signal Name
3
Power_ON
4
GND

FWA6604 Series User’s Manual
8
Pin 5, 6: Hard Disk Drive LED Connector
This connector connects to the hard drive activity LED on control panel. This LED will flash when the
HDD is being accessed.
Pin #
Signal Name
5
+3.3V
6
-HDD_LED
Pin 7, 8: Reset Switch
The reset switch allows the user to reset the system without turning the main power switch off and
then on again. Orientation is not required when making a connection to this header.
Pin #
Signal Name
7
PM_SYSRST#
8
GND
J3: MCU Update (Factory use only)
J4: Serial Port (COM2)
Signal Name
Pin #
Pin #
Signal Name
DCD#
1
6
DSR#
SIN
2
7
RTS#
SOUT
3
8
CTS#
DTR#
4
9
RI#
GND
5
J7: SATA Power Connector
Pin #
Signal Name
1
+5V
2
Ground
3
Ground
4
+12V
J8 : USB 2.0 Pin Header
Signal Name
Pin #
Pin #
Signal Name
NC
1
2
GND
NC
3
4
D+
NC
5
6
D-
GND
7
8
+5V
J10: AT_12V Connector
DC-in internal connector supports +12V.
Remarks: Do not connect CN12 and J10 at the same time.
Pin #
Signal Name
1
+12V
2
Ground

FWA6604 Series User’s Manual
9
FAN1: System Fan Power Connector
Pin header for system fan. The fan must be 12V (Max. 1A).
Pin #
Signal Name
1
Ground
2
+12V
3
Rotation Control
LED1, LED2, LED3, LED4: LAN Port Link, Active LED
LED5: Status LED
A1 & C1 : Status LED
A2 & C2 : Bypass LED
A3 & C3 : Power LED
Signal Name
Pin #
Pin #
Signal Name
SIO_GP27
A1
C1
SIO_GP26
ALARM_R
A2
C2
BY_LED_R
PWR_R
A3
C3
GND
Index port: 4E
Data port: 4F
Device: 07
F5h bit5, bit6 (Control pin)
SW3: Software reset button
Signal Name
Pin #
Pin #
Signal Name
GND
1
2
Intel SoC GPIO7
IO Base:
Read memory 0 x fed0e238 and set bit 1 to “1” as (GPI ),
set bit 1 to “0” as (GPO )
Read memory 0 x fed0e238 and check the bit 0 (Control Pin)
Note: SW3 is controlled by GPIO only.
CN2: Console Port (COM1)
Pin #
Signal Name (RS-232)
1
RTS, Request to send
2
DTR, Data terminal ready
3
TXD, Transmit data
4
Ground
5
Ground
6
RXD, Receive data

FWA6604 Series User’s Manual
10
7
DSR, Data set ready
8
CTS, Clear to send
CN3: Serial ATA Port
CN4: USB2.0 Ports
CN5, CN6, CN7, CN8: LAN 1G / 100M Port
CN9: SO-DIMM DDR3 Socket
CN10: Compact Flash Connector
Note: CF card supports IDE mode only.
If CF card applied, please set the SATA configuration to “IDE mode”in BIOS.
CN11: Mini PCI- E Connector (Half size)
CN12 : DC Power Jack (+12V only)
Note: CN12 and J10 cannot be connected at the same time.

FWA6604 Series User’s Manual
11
Chapter 4 Console Mode Information
FWA6604 supports output information via Console in BIOS level.
Prepare a computer as client loaded with an existing OS such Windows XP.
Connect client computer and FWA6604 with NULL Modem cable.
Follow the steps below to configure the Windows Hyper Terminal application setting:
1. For executing the Hyper Terminal, issue command “hypertrm”.
2. Customize your name for the new connection.
3. Choose the COM port on the client computer for the connection.

FWA6604 Series User’s Manual
12
4. Please make the port settings to Baud rate 115200, Parity None, Data bits 8, Stop bits 1
5. Power up FWA6604 and the screen will display the BIOS information.
6. Press <Tab> key to enter BIOS setup screen in Console mode.
Press <Del> key to enter BIOS setup screen in VGA mode.

FWA6604 Series User’s Manual
13
Chapter 5 Opening the Chassis
Fig. 5-1 Loosen three screws on side and bottom
Fig. 5-2 Remove the top cover
Chapter 6 Installing CompactFlash Card
Fig. 6-1 Insert Compact Flash Card
Fig. 6-2 Push Compact Flash Card into the CF
interface

FWA6604 Series User’s Manual
14
Chapter 7 Installing Memory Module
Fig. 7-1 Insert DDR3L SO-DIMM memory module
Fig. 7-2 Press down the memory module into socket
Chapter 8 Installing Mini PCI-e Module
Fig. 8-1 Insert Half-sized Mini PCI-e module
Fig. 8-2 Push down the module into socket &
tighten one M2 screw

FWA6604 Series User’s Manual
15
Chapter 9 Installing 2.5”HDD / SSD
Fig. 9-1 Put 2.5”HDD / SSD onto the bracket
Fig. 9-2 Fasten HDD on bracket with four M3
Flat screws
Fig. 9-3 Remove two motherboard
screws and fasten two
standoffs
Fig. 9-4 Fix HDD bracket with two motherboard screws and
one Flat screw.
Fig. 9-5 Plug SATA cable
22-pin SATA connector
7-pin SATA connector
4-pin power connector
M3 Flat
screw
Motherboard
screws

FWA6604 Series User’s Manual
16
Chapter 10 Lock Power Connector
Fig. 10-1 Plug power connector into power jack