IBM 7328C1U User manual

System x3200 M3 Types 7327 and 7328
Installation and User’s Guide


System x3200 M3 Types 7327 and 7328
Installation and User’s Guide


Note:
Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 87 and the
IBM Safety Information, and IBM Environmental Notices and User's Guide on the IBM System x Documentation CD, and the
Warranty Information document that comes with the server.
Fourth Edition (October 2010)
© Copyright IBM Corporation 2010.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Safety ............................vii
Chapter 1. The System x3200 M3 server ...............1
The IBM System x Documentation CD.................5
Hardware and software requirements ................5
Using the Documentation Browser .................5
Related documentation ......................6
Notices and statements in this document................7
Features and specifications.....................7
What your server offers......................10
Reliability, availability, and serviceability ................13
IBM Systems Director ......................14
The UpdateXpress System Packs ..................15
Server controls, LEDs, and power ..................15
Front view .........................15
Rear view ..........................20
Server power features .....................21
Chapter 2. Installing optional devices................23
Server components .......................23
System-board internal connectors .................24
System-board optional-device connectors ..............25
System-board switches and jumpers ................26
System-board external connectors.................28
System-board LEDs ......................29
Installation guidelines ......................29
System reliability guidelines ...................30
Working inside the server with the power on .............31
Handling static-sensitive devices .................31
Removing the side cover .....................32
Removing the two-piece bezel ...................32
Installing a memory module ....................35
Unbuffered DIMMs (UDIMMs) ..................36
Registered DIMMs (RDIMMs) ..................37
Installing drives.........................40
Installing a DVD drive .....................41
Installing an optional tape drive ..................43
Installing a hot-swap SAS or hot-swap SATA hard disk drive .......44
IDs for hot-swap hard disk drives .................47
Installing a simple-swap SATA hard disk drive ............47
Power and signal cables for internal drives .............49
Installing an adapter .......................50
Installing the ServeRAID-BR10il v2 SAS/SATA controller .........52
Installing the IBM ServeRAID-MR10i SAS/SATA controller .........53
Installing the IBM ServeRaid-MR-10is VAULT SAS/SATA controller ......56
Installing the virtual media key ...................58
Installing a hot-swap power supply .................58
Installing a security rope clip ....................61
Completing the installation.....................62
Reinstalling the two-piece bezel..................62
Reinstalling the side cover....................64
Connecting the cables .....................65
Updating the server configuration .................65
© Copyright IBM Corp. 2010 iii

Connecting external devices ....................66
Installing the server in a rack....................66
Chapter 3. Configuring the server .................67
Using the Setup utility ......................68
Starting the Setup utility ....................68
Setup utility menu choices....................68
Passwords .........................72
Using the Boot Manager program ..................73
Starting the backup server firmware .................74
Using the ServerGuide Setup and Installation CD ............74
ServerGuide features .....................75
Setup and configuration overview .................75
Typical operating-system installation ................75
Installing your operating system without using ServerGuide .......76
Using the integrated management module ...............76
Using the embedded hypervisor ..................77
Using the remote presence capability and blue-screen capture .......78
Enabling the remote presence feature ...............79
Obtaining the IP address for the IMM................79
Logging on to the Web interface .................79
Enabling the Intel Gigabit Ethernet Utility program ............80
Configuring the Gigabit Ethernet controller ...............80
Enabling and configuring Serial over LAN (SOL) ............80
UEFI update and configuration ..................80
Using LSI Configuration Utility program ................81
Starting the LSI Configuration Utility program .............82
Formatting a hard disk drive ...................83
Creating a RAID array of hard disk drives ..............83
IBM Advanced Settings Utility program ................83
Updating IBM Systems Director ...................84
Appendix A. Getting help and technical assistance ..........85
Before you call .........................85
Using the documentation .....................85
Getting help and information from the World Wide Web ..........85
Software service and support ...................86
Hardware service and support ...................86
IBM Taiwan product service ....................86
Appendix B. Notices ......................87
Trademarks ..........................87
Important notes.........................88
Particulate contamination .....................89
Documentation format ......................89
Electronic emission notices ....................90
Federal Communications Commission (FCC) statement .........90
Industry Canada Class A emission compliance statement ........90
Avis de conformité à la réglementation d'Industrie Canada ........90
Australia and New Zealand Class A statement ............90
United Kingdom telecommunications safety requirement.........90
European Union EMC Directive conformance statement .........91
Taiwanese Class A warning statement ...............91
Germany Electromagnetic Compatibility Directive ...........91
People's Republic of China Class A warning statement .........92
Japanese Voluntary Control Council for Interference (VCCI) statement . . . 92
iv System x3200 M3 Types 7327 and 7328: Installation and User’s Guide

Korean Class A warning statement ................92
Index ............................93
Contents v

vi System x3200 M3 Types 7327 and 7328: Installation and User’s Guide

Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d'installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
© Copyright IBM Corp. 2010 vii

Important:
All caution and danger statements in this documentation begin with a number. This
number is used to cross reference an English caution or danger statement with
translated versions of the caution or danger statement in the IBM Safety Information
book.
For example, if a caution statement begins with a number 1, translations for that
caution statement appear in the IBM Safety Information book under statement 1.
Be sure to read all caution and danger statements in this documentation before
performing the instructions. Read any additional safety information that comes with
the blade server or optional device before you install the device.
viii System x3200 M3 Types 7327 and 7328: Installation and User’s Guide

Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
vDo not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
vConnect all power cords to a properly wired and grounded electrical
outlet.
vConnect to properly wired outlets any equipment that will be attached to
this product.
vWhen possible, use one hand only to connect or disconnect signal
cables.
vNever turn on any equipment when there is evidence of fire, water, or
structural damage.
vDisconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
vConnect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To Connect: To Disconnect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Safety ix

Statement 2:
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
vThrow or immerse into water
vHeat to more than 100°C (212°F)
vRepair or disassemble
Dispose of the battery as required by local ordinances or regulations.
xSystem x3200 M3 Types 7327 and 7328: Installation and User’s Guide

Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
vDo not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
vUse of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A Laser de Classe 1
`
Safety xi

Statement 4:
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
1
2
xii System x3200 M3 Types 7327 and 7328: Installation and User’s Guide

Statement 8:
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact
a service technician.
Statement 11:
CAUTION:
The following label indicates sharp edges, corners, or joints nearby.
Statement 12:
CAUTION:
The following label indicates a hot surface nearby.
Safety xiii

Statement 13:
DANGER
Overloading a branch circuit is potentially a fire hazard and a shock hazard
under certain conditions. To avoid these hazards, ensure that your system
electrical requirements do not exceed branch circuit protection
requirements. Refer to the information that is provided with your device for
electrical specifications.
Statement 15:
CAUTION:
Make sure that the rack is secured properly to avoid tipping when the server
unit is extended.
Statement 17:
CAUTION:
The following label indicates moving parts nearby.
xiv System x3200 M3 Types 7327 and 7328: Installation and User’s Guide

Statement 26:
CAUTION:
Do not place any object on top of rack-mounted devices.
This server is suitable for use on an IT power-distribution system whose maximum
phase-to-phase voltage is 240 V under any distribution fault condition.
Statement 27:
CAUTION:
Hazardous moving parts are nearby.
Safety xv

xvi System x3200 M3 Types 7327 and 7328: Installation and User’s Guide

Chapter 1. The System x3200 M3 server
This Installation and User's Guide contains information and instructions for setting
up your IBM System x3200 M3 Types 7327 or 7328 server, instructions for installing
optional devices, and instructions for cabling, and configuring the server. For
removing and installing optional devices, diagnostics and troubleshooting
information, see the Problem Determination and Service Guide on the IBM System
x Documentation CD, which comes with the server.
The IBM®System x3200 M3 Types 7327 or 7328 server is a 5u-high-high,
high-performance, self-contained server. It is ideally suited for networking
environments that require superior microprocessor performance, improved systems
management, and flexible memory and data management.
Performance, ease of use, reliability, and expansion capabilities were key
considerations in the design of the server. These design features make it possible
for you to customize the system hardware to meet your needs today and provide
flexible expansion capabilities for the future.
The server comes with a limited warranty. For information about the terms of the
warranty and getting service and assistance, see the Warranty Information
document that comes with the server.
The server contains IBM Enterprise X-Architecture®technologies, which help
increase performance, reliability, and availability. For more information, see “What
your server offers” on page 10 and “Reliability, availability, and serviceability” on
page 13.
You can obtain up-to-date information about the server and other IBM server
products at http://www.ibm.com/systems/x/. At http://www.ibm.com/support/
mysupport/, you can create a personalized support page by identifying IBM
products that are of interest to you. From this personalized page, you can subscribe
to weekly e-mail notifications about new technical documents, search for information
and downloads, and access various administrative services.
If you participate in the IBM client reference program, you can share information
about your use of technology, best practices, and innovative solutions; build a
professional network; and gain visibility for your business. For more information
about the IBM client reference program, see http://www.ibm.com/ibm/
clientreference/.
Some server models support four 3.5-inch simple-swap SATA hard disk drives or
four 3.5-inch hot-swap SAS or SATA hard disk drives. The illustrations in this
document might differ slightly from your model.
The following illustration shows the simple-swap server model.
1. Racks are measured in vertical increments of 4.45 cm (1.75 inches) each. Each increment is called a "U." A 1u-high device is 1.75
inches tall.
© Copyright IBM Corp. 2010 1

The following illustration shows the 3.5-inch hot-swap SAS or SATA server model.
The following illustration shows the 2.5-inch hot-swap SAS or SATA server model.
2System x3200 M3 Types 7327 and 7328: Installation and User’s Guide